Craftsman 139.53661SRT1, 139.53671SRT1 Installation Step, Attach the T-rail to the Header Bracket

Page 15

Attach the T-rail to the Header Bracket	[
Installation Step 3

Header

•Position the opener on the garage floor below the header bracket. Use packing material as a protective base.

If the door spring is In the way you'llneed help. Have someone hold the opener securely on a temporary support to allow the T-rail to clear the spring.

•Position the cable pulley bracket against the header bracket.

•Align the bracket holes and join with a clevis pin as shown.

•Insert a ring fastener to secure.

Ring Fastener

Header Bracket

Clevis Pin

5/I 6"x2-3/4 •

Cable

Pulley

Bracket

Garage

Door

Temporary

Support

Hardware Shown Actual Size

	0	©
Ckr_s P_		©
5/16" x 2-3/4"		Ring Fastener
		Ring Fastener

Image 15

Contents Craftsmrn Operation safety Instructions ContentsAdjustment section pages Test the safetyYoull Need Tools Finished Ceiling Center of the door. See pages 12Isaor sigt P,ele=se Garage One-Piece Door Without TrackOne-Piece Door With Track Closed PositionSk2 Carton InventorySecurity+ SquaHo t2Safety Reversing Sensor Installation Hardware Installation HardwareAssemble the T.rail & Attach Cable Pulley Bracket Assembly Section Pages 8Assembly Step Omenlo SasAssembly Step Fasten the T-rail to the OpenerCover \ Check to make sure the chain Is Install Chain/Cable Attach Sprocket CoverUse the second master link to connect Chain to the flat end of the shaftTighten the Chain & Cable Assembly StepInstallation Section Pages 12 Installation Step Determine Header Bracket LocationProceed to , Example Fasten the Header Bracket to the Ceiling Install the Header BracketFasten Header Bracket to the WallAttach the T-rail to the Header Bracket Installation StepPosition the Opener 0SH=OCSlU,G Hang the OpenerBackview Install the Door ControlHardware Shown DryWaAnchomInstall the lens Install the Light and the LensAttach Emergency Release Rope Handle Electrical Requirements Permanent Wiring ConnectionsFacing the door from inside the garage Safety Reversing SystemAlternate Floor Mount Install the Safety Reversing SensorLag St=paB Alternate Wall Mount WithSlotHI,II,l,l,IliiI,%I,I,I,I,D TTIJ.etc-,Pr Igure Fasten Door Bracket=deEd Figure LockWashe 5/6 Ooor Same way, using the 5/16 x I 1/4 clevis pinHole Alignment Connect Door Arm to TrolleyAssembletheDoorArm Adjustment Procedures for One-Piece DoorsPages 28 Adjustment Section Adjustment StepHow and When to Adjust the Limits Adjust the UP and Down LimitsAdjust the Force How and When to Adjust the ForcesImportant safety check Test The Safety Reversing SensorTest the Safety Reverse System Maintenance Schedule Care of Your OpenerTo reduce the risk of severe Lock feature Lock feature is designed toOperation of Your Opener Securityi SECURITY,I Receiver and RemoteControl Programming RgureReview the travel limits adjustment procedures on Having a Problem?Probable Cause and Solution Remote control has short rangeDoor opens but wont close Having a Problem?Probable Cause & Solution SituationRepair Parts Installation PartsRail Assembly Parts 116 Repair PartsOpener Assembly Parts 18173If you have a Premium Control Console AccessoriesFor Sectional Doors Only If you do not have a Premium Control ConsoleSafety wamings 11, 19 Opener Termlnals Access Door/Outside Key Release AccessoryProblems that might require force adjustments Manual Emergency Release Rope & Handle Lockout featureSpanish Please ask For in-home major brand repair service800473-7247 Pare obtener este Manual del

Attach the T-rail to the Header Bracket

Installation Step 3