Craftsman 139.53677SRT1, 139.53671SRT1, 139.53674SRT, 139.53661SRT1 owner manual LockWashe 5/6

Page 25

Please read and comply with the warnings and reinforcement instructions on page 24.

They apply to one-piece doors also.

•Center the bracket on the top of the door, in line with the header bracket as shown. Mark holes

•Ddl! 5/16" pilot holes and fasten the door bracket with hardware supplied,

If the door has no exposed framing, drill 3/16" pilot holes and fasten the bracket with 5/16=x1-I/2" lag screws (not provided) to the top of the door.

The door bracket may be installed on the top edge of the door if required for your installation. (Refer to the dotted line optional placement drawing.) Drill 3/16" pilot holes and substitute

5/16"x1-1/2" lag screws (not provided) to fasten the bracket to the door.

Hardware Shown Actual Size

I_.< _16"-18

LockWashe_ 5/_6"

5/1_'-1_t X 2-1/2 =

Image 25

Contents Craftsmrn Adjustment section pages ContentsTest the safety Operation safety InstructionsYoull Need Tools Finished Ceiling Center of the door. See pages 12One-Piece Door With Track One-Piece Door Without TrackClosed Position Isaor sigt P,ele=se GarageSecurity+ Carton InventorySquaHo t2 Sk2Safety Reversing Sensor Installation Hardware Installation HardwareAssembly Step Assembly Section Pages 8Omenlo Sas Assemble the T.rail & Attach Cable Pulley BracketFasten the T-rail to the Opener Assembly StepCover \ Use the second master link to connect Install Chain/Cable Attach Sprocket CoverChain to the flat end of the shaft Check to make sure the chain IsTighten the Chain & Cable Assembly StepDetermine Header Bracket Location Installation Section Pages 12 Installation StepProceed to , Example Fasten Header Install the Header BracketBracket to the Wall Fasten the Header Bracket to the CeilingAttach the T-rail to the Header Bracket Installation StepPosition the Opener 0SH=OCSlU,G Hang the OpenerHardware Shown Install the Door ControlDryWaAnchom BackviewInstall the Light and the Lens Install the lensAttach Emergency Release Rope Handle Electrical Requirements Permanent Wiring ConnectionsFacing the door from inside the garage Safety Reversing SystemLag St=paB Install the Safety Reversing SensorAlternate Wall Mount WithSlot Alternate Floor MountHI,II,l,l,IliiI,%I,I,I,I,D Fasten Door Bracket TTIJ.etc-,Pr Igure=deEd Figure LockWashe 5/6 Hole Alignment Same way, using the 5/16 x I 1/4 clevis pinConnect Door Arm to Trolley OoorAssembletheDoorArm Adjustment Procedures for One-Piece DoorsHow and When to Adjust the Limits Adjustment Section Adjustment StepAdjust the UP and Down Limits Pages 28Adjust the Force How and When to Adjust the ForcesTest The Safety Reversing Sensor Important safety checkTest the Safety Reverse System Care of Your Opener Maintenance ScheduleTo reduce the risk of severe Lock feature is designed to Lock featureOperation of Your Opener Control Programming Receiver and RemoteRgure Securityi SECURITY,IProbable Cause and Solution Having a Problem?Remote control has short range Review the travel limits adjustment procedures onProbable Cause & Solution Having a Problem?Situation Door opens but wont closeInstallation Parts Repair PartsRail Assembly Parts Opener Assembly Parts Repair Parts18173 116For Sectional Doors Only AccessoriesIf you do not have a Premium Control Console If you have a Premium Control ConsoleProblems that might require force adjustments Access Door/Outside Key Release AccessoryManual Emergency Release Rope & Handle Lockout feature Safety wamings 11, 19 Opener Termlnals800473-7247 For in-home major brand repair servicePare obtener este Manual del Spanish Please ask