Craftsman 139.53671SRT1, 139.53677SRT1 Operation of Your Opener, Lock feature is designed to

Page 32

Operation of Your Opener

Activate the opener with any of the following:

•The Remote Control: Hold push button down until the door starts to move.

•The Door Control: Hold push button down until the door starts to move.

•The Outdoor Key Switch or Keyless Entry. (See Accessories)

When the opener is activated with the safety reversing sensor installed and correcUy aligned:

Weak or broken springs could allow an open door to fall (either rapidly or unexpectedly), resulting in serious injury, death or property

damage. If possible, use the emergency release rope and handle only when the door is fully closed.

1.If open, the door will close. If closed, the door will open.

2.If closing, the door will reverse.

3.If opening, the door will stop (allowing space for entry and exit of pets and for fresh air).

4.If the door has been stopped in a partially open position, it will close.

5.If obstructed while closing, the door will reverse.

6.if obstructed while opening, the door will stop.

7.The garage door will reverse in the closingcycle when the invisible beam is broken, if fullyopen, the door will not close when the beam is broken. The sensor has

no effect in the opening cycle.

If the sensor is not installed or not aligned correctly, the door won'tclose from any remote control. You can close the door with the Door Control, the Outdoor Key

Switch, or Keyless Entry, however, if you activate

them until down travel is complete. If you release them too soon, the door will reverse.

The opener lights will blink for 5 seconds when the safety reversing sensor causes the door to reverse.

The Opener Lights will turn on under the following conditions: When the opener is initially plugged in; when the power is interrupted; when the opener is activated.

They will turn off automatically after 4-1/2 minutes or

provide constant light when the Light feature on the

Premium Control Console is activated. SECURITY,I, models: Lights will also turn on when someone walks through the open garage door. Bulb size is 75 watts maximum.

Emergency

Release Handle

(Pull Down)

Manual disconnect position

The lockout feature prevents the trolley from reconnecting automatically. Pull the emergency handle down and back (toward the opener). The door can then be raised and lowered manually as often as necessary. To disengage the lookout feature, pull the emergency handle straight down. The trolley will reconnect on the next UP or DOWN operation.

To open the door manually:

The door should be

fully closed if possible. Pull down on the red

emergency release handle and lift the door

manually. To reconnect the door to

the opener, press the Door Control push button.

O _

.

Trolley

 

 

Release Arm

Emergency

Release Handle

(Pull Doom& Back

Towards Opener)

Lockout position

Operation

of the Door Controls (see page 18)

(SECURITY.I, models: See additional programming features, next page.)

Press the lighted push button to open or close the

Premium Console

(cont.):

door.

 

Lock feature: The

Lock feature is designed to

Press again to reverse the door during the closing

prevent operation of the door from remote controls.

However, the door will open and close from the

cycle or to stop the door while it'sopening.

Door Control, the Outdoor Key Switch and the

Premium Console:

 

 

Keyless Entry Accessories.

Light feature: Press the large round Light button, if

To activate: Press and hold the small round Lock

the opener light is off, it will tum on. If the opener

button for 2 seconds. The push button light will

light is on, (even in the 4-1/2 minute automatic

flash as long as the Lock feature is on.

cycle) it will turn off.

 

 

To turn off: Press and hold the Lock button again

But if you use the Light button to turn the lights on

for 2 seconds.The push button light will stop

and then activate the opener, the lights will turn off

flashing. The Lock feature will also turn off

after 4-1/2 minutes.

 

 

whenever the SRT button on the opener panel is

The Light button will not control the opener lights

activated.

 

when the door is in motion.

 

 

 

32

Page 31 Page 33
Image 32
Page 31 Page 33
Contents Craftsmrn Contents Adjustment section pagesTest the safety Operation safety InstructionsYoull Need Tools Center of the door. See pages 12 Finished CeilingOne-Piece Door Without Track One-Piece Door With TrackClosed Position Isaor sigt P,ele=se GarageCarton Inventory Security+SquaHo t2 Sk2Installation Hardware Safety Reversing Sensor Installation HardwareAssembly Section Pages 8 Assembly StepOmenlo Sas Assemble the T.rail & Attach Cable Pulley BracketCover \ Assembly StepFasten the T-rail to the Opener Install Chain/Cable Attach Sprocket Cover Use the second master link to connectChain to the flat end of the shaft Check to make sure the chain IsAssembly Step Tighten the Chain & CableProceed to , Installation Section Pages 12 Installation StepDetermine Header Bracket Location Example Install the Header Bracket Fasten HeaderBracket to the Wall Fasten the Header Bracket to the CeilingInstallation Step Attach the T-rail to the Header BracketPosition the Opener Hang the Opener 0SH=OCSlU,GInstall the Door Control Hardware ShownDryWaAnchom BackviewAttach Emergency Release Rope Handle Install the lensInstall the Light and the Lens Permanent Wiring Connections Electrical RequirementsSafety Reversing System Facing the door from inside the garageInstall the Safety Reversing Sensor Lag St=paBAlternate Wall Mount WithSlot Alternate Floor MountHI,II,l,l,IliiI,%I,I,I,I,D =deEd Figure TTIJ.etc-,Pr IgureFasten Door Bracket LockWashe 5/6 Same way, using the 5/16 x I 1/4 clevis pin Hole AlignmentConnect Door Arm to Trolley OoorAdjustment Procedures for One-Piece Doors AssembletheDoorArmAdjustment Section Adjustment Step How and When to Adjust the LimitsAdjust the UP and Down Limits Pages 28How and When to Adjust the Forces Adjust the ForceTest the Safety Reverse System Important safety checkTest The Safety Reversing Sensor To reduce the risk of severe Maintenance ScheduleCare of Your Opener Operation of Your Opener Lock featureLock feature is designed to Receiver and Remote Control ProgrammingRgure Securityi SECURITY,IHaving a Problem? Probable Cause and SolutionRemote control has short range Review the travel limits adjustment procedures onHaving a Problem? Probable Cause & SolutionSituation Door opens but wont closeRail Assembly Parts Repair PartsInstallation Parts Repair Parts Opener Assembly Parts18173 116Accessories For Sectional Doors OnlyIf you do not have a Premium Control Console If you have a Premium Control ConsoleAccess Door/Outside Key Release Accessory Problems that might require force adjustmentsManual Emergency Release Rope & Handle Lockout feature Safety wamings 11, 19 Opener TermlnalsFor in-home major brand repair service 800473-7247Pare obtener este Manual del Spanish Please ask
Top Page Image Contents