Craftsman 139.53661SRT1, 139.53671SRT1 Install the lens, Install the Light and the Lens

Page 19

6.Attach the User Safety Instruction label to the wall neat the door control, and the Maintenance Instruction label in a prominent location on the inside of the garage door.

Page 32 explains how to use the door control.

Installation Step 7

Install the Light and the Lens

Install the light:

•Install a 75 watt maximum light bulb in each socket. The lights will turn ON and remain lit for approximately 4-1/2 minutes when power is connected. Then the lights will turn OFF.

•If the bulbs bum out prematurely due to vibration, replace them with standard neck "Garage Door Opener =bulbs.

Install the lens:

•Apply slight pressure on the sides of each lens and slide the tabs into the slots in the side panels.

', For convenience, the lens may be Installed after Adjustment Step 4 on page 30.

•Reverse the procedure to remove the lenses.

,r

Do NOT connect the power and operate the openerat this time. The trolley will travel to the full open position but wilt not return to the

close position until the sensor beam is connected and properly aligned.

See Safety Reversing Sensor instructions beginning on page 21.

Installation

Step 8

 

Attach

the Emergency

 

Release

Rope

and Handle

I

•Thread one end of the rope through the hole in the top of the red handle so "NOTICE" reads dght

side-up a_shown. Secme with an overhand knot.

The knot should be at least 1" from the end of the rope to prevent slipping.

:• Thread the other end of the rope through the hole in the release arm of the outer trolley.

•Adjust rope length so the handle is 6 feet above the floor. Secure with an overhand knot.

If it is necessary to cut the rope, heat seal the cut end with a ma_ch or lighter to prevent unraveling.

Do not use the red handle to pull the door

open or closed. The rope knot could become untied and you could fall. Use the emergency release only to disengage the trolley and, if possible, only when the door Is closed.

Garage doors are heavy. _t the door is open when the handle is pulled, the door could

close inadvertently if it Is not properly balanced. Serious Injury may result to persons under the door. Make sure the doorway is clear of persons and obstructions before pulling handle when door is open.

r

P.ekmseAnn

Rem Handle

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Craftsmrn Operation safety Instructions ContentsAdjustment section pages Test the safetyYoull Need Tools Finished Ceiling Center of the door. See pages 12Isaor sigt P,ele=se Garage One-Piece Door Without TrackOne-Piece Door With Track Closed PositionSk2 Carton InventorySecurity+ SquaHo t2Safety Reversing Sensor Installation Hardware Installation HardwareAssemble the T.rail & Attach Cable Pulley Bracket Assembly Section Pages 8Assembly Step Omenlo SasFasten the T-rail to the Opener Assembly StepCover \ Check to make sure the chain Is Install Chain/Cable Attach Sprocket CoverUse the second master link to connect Chain to the flat end of the shaftTighten the Chain & Cable Assembly StepDetermine Header Bracket Location Installation Section Pages 12 Installation StepProceed to , Example Fasten the Header Bracket to the Ceiling Install the Header BracketFasten Header Bracket to the WallAttach the T-rail to the Header Bracket Installation StepPosition the Opener 0SH=OCSlU,G Hang the OpenerBackview Install the Door ControlHardware Shown DryWaAnchomInstall the Light and the Lens Install the lensAttach Emergency Release Rope Handle Electrical Requirements Permanent Wiring ConnectionsFacing the door from inside the garage Safety Reversing SystemAlternate Floor Mount Install the Safety Reversing SensorLag St=paB Alternate Wall Mount WithSlotHI,II,l,l,IliiI,%I,I,I,I,D Fasten Door Bracket TTIJ.etc-,Pr Igure=deEd Figure LockWashe 5/6 Ooor Same way, using the 5/16 x I 1/4 clevis pinHole Alignment Connect Door Arm to TrolleyAssembletheDoorArm Adjustment Procedures for One-Piece DoorsPages 28 Adjustment Section Adjustment StepHow and When to Adjust the Limits Adjust the UP and Down LimitsAdjust the Force How and When to Adjust the ForcesTest The Safety Reversing Sensor Important safety checkTest the Safety Reverse System Care of Your Opener Maintenance ScheduleTo reduce the risk of severe Lock feature is designed to Lock featureOperation of Your Opener Securityi SECURITY,I Receiver and RemoteControl Programming RgureReview the travel limits adjustment procedures on Having a Problem?Probable Cause and Solution Remote control has short rangeDoor opens but wont close Having a Problem?Probable Cause & Solution SituationInstallation Parts Repair PartsRail Assembly Parts 116 Repair PartsOpener Assembly Parts 18173If you have a Premium Control Console AccessoriesFor Sectional Doors Only If you do not have a Premium Control ConsoleSafety wamings 11, 19 Opener Termlnals Access Door/Outside Key Release AccessoryProblems that might require force adjustments Manual Emergency Release Rope & Handle Lockout featureSpanish Please ask For in-home major brand repair service800473-7247 Pare obtener este Manual del
Top Page Image Contents