Craftsman 139.53610, 139.53403 owner manual STE P 2 A.ach Tee Rail to Header Bracket, 16 x2-3/4

Page 11

installation

STE P 2 A.ach Tee Rail to Header Bracket

Clevis Pin

@/_ Cotter

5/16 'x2-3/4

Ring OrpinI

Fastener

 

PROCEDURE: Position opener chassis on garage floor below header bracket. Use packing material

base to protect cover NOTE: To enable Tee rail to clear sectional door springs, it may be necessary to lift the chassis onto a temporary support.

CAUTION: Chassis must either be secured to the support or held firmly in place by another person_

Raise Tee rail until cable pulley and header brackets come together Align bracket holes and join with clevis pin as shown. Secure with a ring or cotter pin fastener(if cotter pin is used, spread to secure)

g Malerial

STE P 3 Position Opener Chassis

Follow instructions which apply to your door type as illustrated below

TO PREVENT DAMAGE TO ALL LIGHTWEIGHT DOORS AND DOORS WITH WINDOWS, DO NOT REST THE OPENER ON THE DOOR.

SECTIONAL

and

ONE-PIECE

ONE-PIECE DOOR

DOOR

WiTH

TRACK

WiTH NO - TRACK

I NSTALLATION

i N STA LLATI ON

NOTE: A 2x4 is convenient for setting an ideal

door-to-Tee rail distance. It is not necessary where headroom is insufficienL

PROCEDURE: Raise the opener chassis onto a step- ladder Open garage door Place a 2x4 on edge on

top section of door near centerline Rest Tee rail on 2x4

PROCEDURE: Measure the distance from floor to

top of door (in fully open position and parallel to the floor)

Using a stepladder as a support, raise the opener chassis to the same distance from the floor (chassis will have a slight angle as shown)

The top of the door should be levet with the top of the opener For maximum efficiency, do not position the opener chassis more than 2 inches above this point.

Tee Rail

2x4

Header

Bracket

•

TOp Of ODenet

Door

I BracketI

I Equal

r_ Dstance _

I lromI

I FloorI

II

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents 3953606 Specifications Features of Your OpenerLink Assembly Hardware InstallationCarton Check List Youll Need ToolsLocks to avoid damage to garage door Start By Reading These Impo ant Safety RulesDisengage ALL Existing Garage Door Care of the Opener Check Chain TENSION. Adjust if necessaryReplace the Transmitter BATTERY, preferably be- fore winter Operation of Your OpenerTee Rail AssemblyST P 1 Assemble Tee Rail & Attach Cable Pulley Bracket To the chassis with washered screws previously AssernbiySTE P 3 Attach Tee Rail to Opener Chassis To Fully Engage Trolley With a hammer TabPlate Pulley Install Chain and Cable Link Garage Door Opener STE P 5 TightenChain and Cable MAY Find ITExample InstallationSTE P 1 Position & Install Header Bracket Sectional Door16 x2-3/4 STE P 2 A.ach Tee Rail to Header BracketCheckto make sure Tee rail is centered over door Hang Opener ChassisSTE P 5 Attach Emergency Release Rope & HandleInfrared Reversing System Wiring Instructions for AccessoriesTop FtangeLighl Lensab75LightWattBulbMaX STE P 7 Install Light and LensProcedure Refer to illustration Make connec Nut STE P 9 Install Door Bracket and PlateReinforcement STE P 10 Connect Door Arm to Trolley Installation onlyDoor Installations Adjustment ProceduresForce Adjustment Chart AdjustmentAdjust Force Limit Adjustment ChartSectional Door Test Safety Reverse SystemReceiver Radio ControlsTransmitter ReceivertransmitterSituation Probable Cause & Solution Having a Problem?Doesnt Turn OFF Situation Probable Cause & SolutionDoor Wont Close Door TravelDescription Repair PartsRAI L Assembly Parts List KEY PartRetaining Repair Parts Chassis Assembly Parts ListKEY Part Description WasherLimitation on Liability HOW to Order Repair PartsFull DAY Warranty On Garage Door Opener Limited Warranty
Top Page Image Contents