Wayne-Dalton 9400, 9100, 9600 installation instructions Operator Bracket, U ar

10	Operator Bracket
	NOTE: Operator bracket must be mounted
Tools Needed:
Power Drill	and secured prior to installing top section.
	NOTE: If an idriveTM operator is to be
7/16” Socket	installed, the operator bracket is not
Driver	required to be installed.
Vice Clamps	IMPORTANT: WHEN INSTALLING A
	TROLLEY TYPE OPERATOR ON 9100, 9400
Phillips Head	AND 9600 SERIES DOORS, A WAYNE-
	DALTON TROLLEY BRACKET MUST
Screwdriver	BE SECURELY ATTACHED TO THE TOP
	SECTION, ALONG WITH ANY U-BAR’S
	INITIALLY PROVIDED WITH THE DOOR. IT IS
	THEN UNNECESSARY TO FURTHER
	REINFORCE THE TOP SECTION OF THIS
	WAYNE-DALTON DOOR WHEN ATTACHING
	A TROLLEY TYPE OPERATOR, AS LONG AS
	THE INSTALLATION OF THE OPERATOR IS
	ACCORDING TO WAYNE-DALTON’S
	INSTRUCTIONS AND FORCE SETTINGS ARE
	ADJUSTED PROPERLY.
	Locate the center of the top section and
	place the operator bracket on top of the
	section as illustrated. Align the center of
	the bracket with the center line of the
	top section. For retro fit applications, the
	operator bracket must be aligned with an
	existing operator and positioned on the top
	section as illustrated.
	Install (2) #12 x 1/2” phillips head screws
	on the top flange of the operator bracket.
	U-BAR INSTALLED: If a U-Bar is installed
	on the top section, clamp the bottom flange
	of the operator bracket to the U-Bar. Make
	sure the bottom flange of the bracket
	is held in place, flush against the U-Bar
	before continuing.
	NO U-BAR INSTALLED: If a U-Bar is not
	installed on the top section, continue with
	the steps below.
	Attach (4) 1/4”- 14 x 5/8” self tapping
	screws to the front of the operator bracket.
	Next attach (2) 1/4”- 14 x 5/8” self tapping
	screws to the bottom flange of the operator
	bracket. Remove vice clamps if placed on
	operator bracket previously.
	NOTE: If you have a 9100 door, use (2)
	1/4”- 20 x 11/16” self drilling screws
	used to attach the U-Bar instead of the (2)
	1/4”- 14 x 5/8” self tapping screws when
	attaching the bottom flange of the operator
	bracket to U-Bar.
	NOTE: When attaching an operator bracket
	to the top section with a U-Bar installed,
	apply additional pressure to thread the
	fasteners into the U-Bar.
18

center		top
	Operator	flange
line
		front
	Bracket

bottom

flange U-bar

Top section	Top
With or
	section
without U-bar

Operator Bracket

U	ar
-
	b

	(2) #12 x 1/2”	bottom
		flange
	Phillips head
top	screws	Vice clamp
flange		NOTE: not required for j-struts.
Top flange installation		installation with u-bar
	Operator	(2) 1/4”- 14 x 5/8”
front	bracket	self tapping screws
		Operator
		bracket
	U ar
	-
	b	U ar
		-
(4) 1/4”- 14 x 5/8”		b
		bottom
self tapping
screws		flange
installation with u-bar		installation with u-bar
		(6) 1/4”- 14 x 5/8”
		Self tapping
		screws
		Operator
		bracket

installation without u-bar

Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer. To find your local Wayne-Dalton dealer, refer to your

local yellow pages/business listings or go to the Find a Dealer section online at www.wayne-dalton.com