Manuals / Wayne-Dalton / Household Appliance / Garage Door Opener

Wayne-Dalton AND 9600 installation instructions 9100, 9400, AND

Models: AND 9600 9400

1 48

Download 48 pages 56.14 Kb

Page 1

Image 1

9100, 9400, AND 9600

TorqueMaster® Plus - Single and Double Spring

Installation Instructions and Owner’s Manual

Wayne-Dalton, a Division of Overhead Door Corporation P.O. Box 67, Mt. Hope, OH 44660 www.Wayne-Dalton.com

IMPORTANT NOTICE!

Read these instructions carefully before attempting installation. If in question about any of the proce- dures, do not perform the work. Instead, have a qualified door agency do the installation or repairs.

Part No. 327684

REV4 03/01/2012

Page 1

Image 1

Wayne-Dalton AND 9600 installation instructions 9100, 9400, AND, TorqueMaster Plus - Single and Double Spring

Contents

9100, 9400, AND Installation Instructions and Owner’s ManualTorqueMaster Plus - Single and Double Spring Table of Contents After installation is complete, fasten this manual near garage doorDefinition of key words used in this manual Package Contents Door Section Identification Tools Required Page TorqueMaster Spring Removal Removal continued TorqueMaster SpringExtension Spring Removal PRE-INSTALLATIONRemoving the Old Door Failure to securely Preparing the Openingattach a suitable mounting pad to structurally sound framing could causeAttaching Quick Install Flag InstallationINSTALLATION Angles to Vertical TrackHorizontal Angle Attaching Fully Adjustable Flagangles to Vertical TrackINSTALLATION Installing Q.I. Jamb BracketsDrums 3rd SET HOLESVertical Track Bottom SectionTop Brackets Stacking Sections2 1/4”-14 X 5/8” 4 1/4” - 14 x 5/8”U-Bar - Asymmetrical U-BarOperator Bracket INSTALLATIONTop Section INSTALLATION Quick Install FlagangleAttaching Horizontal Track to 3/8” - 16 X 3/4”Attaching Horizontal Track to Adjustable Flagangleflagangle ribbed trackAdjusting Top Brackets Center Bracket Bushing TorqueMaster Spring TubeTorqueMaster Spring Tube LABELED END idrive Installation Drum Wraps Cable Drums INSTALLATIONCARRIAGE BolT End BracketsINSTALLATION Assemblymust install the center bracket bushing assembly. Follow these instructions forPositioning Support Bracket Attaching Disconnect Cables INSTALLATIONMounting Disconnect Handle Bracketscrewdriver Attaching Disconnect HandleScrew Cable Adjustment INSTALLATIONTools Needed Pliers/Wire Cutters Flat Tip Screwdriver Securing Door for Spring Windinginstall ti Drum Wrap InstallationWinding Springs ingratchets removbWinding Springs Continued Rear Support Rear Support Continued INSTALLATIONInstructions TorqueMaster Plus ResetINSTALLATION TorqueMaster Plus Reset Instructions Continuedplace vice clamps Pawl Knob in Lower PositionInstructions Continued TorqueMaster Plus ResetSide Lock optional INSTALLATIONDoorMaster TM Bracket Step Plate DO NOT INSTALL PULL ROPES optional INSTALLATIONPull Rope ON DOORS WITH ELECTRICassembly, as shown in FIG Trolley Installation forStandard Lift Determine the Wayne-DaltonLow Headroom optional5. Attach operator to ceiling using perforated angle 3. Attach door arm to operator bracket installed in StepTrolley Operator IMPORTANT Angle must be attached to framing membersmaintenance CleaningPainting Painting Continued Lifetime Limited Warranty Models 9100, 9400 Thank you for your purchase Please Do Not Return This Product To The Store