| TorqueMaster® Plus Reset |
|
|
|
|
|
|
|
|
| Instructions Continued... |
|
|
|
|
|
|
|
|
Tools Needed: | NOTE: Single spring applications require |
| place vice clamps | ||||||
no spring winding on left hand side. |
| ||||||||
|
| ||||||||
|
| above 3rd Roller on | |||||||
|
|
| |||||||
| Clamp a pair of vice clamps on the vertical |
| both vertical track | ||||||
| tracks just above the third roller on one |
|
|
|
|
|
|
|
|
| side and just below the third roller on the |
|
|
|
|
|
|
|
|
| other side. This will prevent the door from |
|
|
|
|
|
|
|
|
| raising or lowering while adjusting the |
|
|
|
|
|
|
|
|
| spring(s). |
| vice clamps |
|
|
|
|
| Track |
|
|
| attached to |
|
|
|
|
| |
| WARNING |
| inner rail |
|
|
|
|
|
|
|
| of track |
|
|
|
|
|
| |
| Prior to winding or making adjustments |
|
|
|
|
|
|
|
|
| to the springs, ensure you’re winding |
|
|
|
|
|
|
|
|
| in the proper direction as stated in the |
|
|
|
|
|
|
|
|
| Installation Instructions. Otherwise the |
|
|
|
|
|
|
|
|
| spring fittings may release from spring |
|
|
|
|
|
|
|
|
| if not wound in the proper direction and |
|
|
|
|
|
|
|
|
| could result in severe or fatal injury. |
|
|
|
|
|
|
|
|
| To Add Spring Tension: | Lower Position | UPPER Position | ||||||
| The ratchet wheel is made of 10 teeth. To |
|
|
|
|
|
|
|
|
| add spring tension, ensure the ratchet and |
|
|
|
|
|
|
|
|
| socket is set so that it will tighten counter |
|
|
|
|
|
|
|
|
| clockwise on the right hand side, and |
|
|
|
|
|
|
|
|
| clockwise on the left hand side. Place the |
|
|
|
|
|
|
|
|
| ratchet with 5/8” socket onto the wind- |
|
|
|
|
|
|
|
|
| ing shaft, pull down to add 3/10 of a turn. |
|
|
|
|
|
|
|
|
| Watch as three teeth of the ratchet wheel |
|
|
|
|
|
|
|
|
| pass over the ratchet pawl, creating three |
|
|
|
|
|
|
|
|
| “clicks”. |
|
|
|
|
|
|
|
|
| To Remove Spring Tension: |
|
|
|
|
|
|
|
|
| To remove spring tension, ensure the |
|
|
|
|
|
|
|
|
| ratchet and socket is set so that it will |
|
|
|
|
|
|
|
|
| tighten counter clockwise on the right |
|
|
|
|
|
|
|
|
| hand side and clockwise on the left hand |
|
|
|
|
|
|
|
|
| side. It is recommended that a regular 5/8” | Pawl knob in Lower | Pawl knob in upper | ||||||
| wrench be used. Place the wrench onto | ||||||||
| Position | Position | |||||||
| the winding shaft. Pull down on the wrench | ||||||||
|
|
|
|
|
|
|
|
| |
| to relieve pressure between the ratchet |
|
|
|
|
|
|
|
|
| pawl and the ratchet wheel. Push in on |
|
|
|
|
|
|
|
|
| the pawl to allow the three ratchet wheel |
|
|
|
|
|
|
|
|
| teeth to pass by the ratchet pawl, as you | End Bracket |
|
|
|
|
|
|
|
| carefully allow the wrench to be rotated |
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
| |
| upward by the spring tension. Release the |
|
|
|
|
|
|
|
|
| pawl to allow ratchet pawl to engage with |
|
|
|
|
|
|
| Ratchet |
| the ratchet wheel. |
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
| with 5/8” | |
|
|
|
|
|
|
|
|
| |
| Remove the vice clamps from the vertical |
|
|
|
|
|
|
| Socket |
| tracks, |
|
|
|
|
|
|
|
|
| if necessary. When door is balanced and |
|
|
|
|
|
|
|
|
| adjusted properly, place the pawl knobs in |
|
|
|
|
|
|
|
|
| the active position (lower position). |
|
|
|
|
|
|
|
|
|
| PAWL | To |
|
|
|
|
| |
|
|
| fatal |
|
|
|
|
| |
|
|
|
|
| , |
|
|
|
|
|
|
|
| until | DO |
|
|
|
|
|
|
|
| from |
|
|
|
| |
|
|
| To | spr |
|
|
|
| |
|
|
|
| safely |
|
|
|
| |
|
|
| and follow read |
|
|
|
| ||
|
| 3” Extension | installationthe |
|
|
|
| ||
|
| DO | Ratchet | REMOVE Tns/owners |
| ||||
|
|
|
| NOT | instructiotions in | the | e | ||
|
|
|
| No space | manual. |
|
|
| |
|
|
|
|
| HIS |
|
|
| |
|
|
|
| CablePawland | TAG. |
| |||
|
|
|
|
| Drum |
| geRatcheum t | ||
|
|
|
|
| DISENGAGE |
|
|
| |
38 |
|
|
|
|
|
|
|
|
|
Please Do Not Return This Product To The Store. Contact your local
local yellow pages/business listings or go to the Find a Dealer section online at