Wayne-Dalton AND 9600, 9400 TorqueMaster Plus Reset Instructions Continued, Installation, Pawl

Models: AND 9600 9400

1 48
Download 48 pages 56.14 Kb
Page 37
Image 37
TorqueMaster® Plus Reset

Tools Needed:

TorqueMaster® Plus Reset

Instructions Continued...

If the system is activated, follow these steps to reset the system:

3.Clamp vice grips on both vertical tracks just below the bottom section.

4.Flip the pawl knob on both end brackets to the upper position (see illustration).

5.With assistance, raise the door slightly to reset the system.

IMPORTANT: BE PREPARED TO SUPPORT THE TOTAL WEIGHT OF THE DOOR.

place vice clamps

BELOW BOTTOM SECTION on both vertical track

6.Cautiously remove the vice clamps from the vertical tracks; with assistance, lower the door.

IMPORTANT: BE PREPARED TO HOLD THE FULL TENSION OF THE SPRING.

7.Check for spring tension. Starting on the right hand side, place a ratchet and 5/8” socket on the Torquemaster® Plus end bracket (see illustration). Ensure ratchet is set so that it will tighten counter clockwise on the right hand side, and clockwise on the left hand side (if applicable). If ten- sion is present, remove the ratchet and check the left hand side (if applicable). If spring(s) have tension, proceed to Step 8; if no spring tension is present, contact a qualified door agency to replace the spring(s).

Lower Position

Pawl Knob in Lower

Position

UPPER Position

Pawl knob in UPPER

Position

INSTALLATION

NOTE: A 3” extension is also recommended for added clearance from the horizontal angle.

8.Lift door and check its balance. Adjust spring(s), if door lifts by itself (hard to pull down) or if door is difficult to lift (easy to pull down). Anytime spring adjustments are made, pawl knob must be in the upper position (see illustration).

An unbalanced door such as this can cause idrive® or Torquemaster® opera- tion problems. To adjust spring(s), only add or remove a maximum of 3/10 of a turn (three teeth of ratchet wheel) at a time. Both sides need to be adjusted equally on double spring doors.

End Bracket

Ratchet with 5/8” place vice clamps Socket

PAWL

 

To

 

 

 

 

 

 

 

 

 

fatal

,

 

 

 

 

 

 

 

 

 

until

from

 

 

 

 

 

 

 

To

spr

 

 

 

 

 

 

 

 

 

safely

 

 

 

 

 

 

 

 

 

and follow

 

read

i

(

 

 

3” Extension

 

installationthe d

ire

 

 

 

 

DO

NOT

 

 

 

 

 

 

 

 

 

instructiotions

in

 

 

 

 

 

manual

 

 

Dr

 

 

No space betREMOVE. ns/ownersthe

 

 

 

 

Ratchet

Pawlweena

 

THIS

TA

 

 

 

 

 

Cable

Drum

nd

 

 

 

G.

e Ratchet

 

 

 

 

DISENGAGED

SIDE VIEW

 

 

um

 

 

 

 

 

 

 

 

 

 

 

DISENG

AGED U

 

 

 

 

 

 

 

 

 

 

 

NDERNEATH VIEW

 

 

 

 

 

 

 

37

Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer. To find your local Wayne-Dalton dealer, refer to your

local yellow pages/business listings or go to the Find a Dealer section online at www.Wayne-Dalton.com

Page 37
Image 37
Wayne-Dalton AND 9600 TorqueMaster Plus Reset Instructions Continued, Installation, place vice clamps, Pawl, 3” Extension