12 | Attaching Horizontal Track to Adjustable |
| FLAGANGLE |
| horizontal |
| Flagangle |
|
|
| track |
|
|
|
|
| |
Tools Needed: | To install horizontal track, place the curved end over |
|
|
|
|
9/16” Socket | the top roller. Align the bottom of the horizontal track |
|
|
|
|
with the vertical track. Hand tighten the horizontal |
|
|
|
| |
|
|
|
|
| |
7/16” Socket | track to the flagangle with (2) 1/4”- 20 x 5/8” carriage |
|
|
| (2) 1/4”- 20 x 5/8” |
bolts and (2) 1/4”- 20 flange hex nuts. |
|
|
| ||
|
|
|
| ||
|
|
|
| carriage bolts | |
Ratchet Wrench |
|
|
|
| |
Level the horizontal track assembly and bolt the |
|
|
|
| |
|
|
|
|
| |
9/16” Wrench | horizontal angle to the slot in the flagangle using |
|
|
|
|
Level | (1) 3/8”- 16 x 3/4” hex head bolt and (1) 3/8”- 16 hex |
| (2) 1/4”- 20 flange |
| |
nut. Repeat for other side. Remove the nail that was |
| hex nuts |
| vertical track | |
Hammer | temporarily holding the top section in place, installed |
|
| hORIZONTAL ANGLE |
|
in Step 11. |
| (1) 3/8”- 16 |
| ||
|
|
|
| ||
|
|
| Hex nut |
|
|
| IMPORTANT: Failure to remove nail before |
|
|
|
|
| attempting to raise door could cause |
|
|
|
|
| permanent damage to top section. |
|
|
|
|
| WARNING |
|
|
| TRACK |
|
|
|
|
| HORIZONTAL |
|
|
|
| (1) 3/8”- 16 X 3/4” |
|
| DO NOT RAISE DOOR UNTIL HORIZONTAL |
|
| hex HEAD BOLT |
|
| TRACKS ARE SECURED AT REAR, AS |
|
|
|
|
| OUTLINED IN STEP 21, OR DOOR COULD FALL |
|
|
| |
| FROM OVERHEAD POSITION CAUSING SEVERE |
|
|
| |
13 | OR FATAL INJURY. |
|
|
|
|
Adjusting Top Brackets |
|
| HORIZONTAL | ||
|
|
| |||
|
|
| track |
| |
Tools Needed: | With horizontal tracks installed, you can |
| top |
|
|
section |
|
| |||
| now adjust the top brackets. Vertically |
|
| ||
7/16” Wrench |
|
|
|
| |
align the top section of the door with the |
|
|
|
| |
|
|
|
|
| |
| lower sections. Once aligned, position |
|
|
|
|
| the top bracket slide, out against the |
|
|
|
|
| horizontal track. |
|
|
|
|
Maintaining the slide’s position, tighten |
| TOP |
the (2) 1/4”- 20 flange hex nuts to |
| ROLLER |
secure the top roller slide to the top | Correct | TOP |
bracket base. |
| |
| BRACKET | |
|
| |
|
| SLIDE |
| top | (2) 1/4”- 20 |
| section | |
| FLANGE HEX | |
|
| NUTS |
|
| top |
|
| section |
20
inCorrect
Please Do Not Return This Product To The Store. Contact your local
local yellow pages/business listings or go to the Find a Dealer section online at
