Electrolux 40300 manual Connecting the Dishwasher, Water Connection, Permitted water pressure

Page 31

Installation and Connection Instructions

Connecting the Dishwasher

Water Connection

The dishwasher is fitted with safety devices that prevent the wash water returning into the drinking water system and comply with the applicable plumbing regulations.

The dishwasher can be connected to cold and hot water supplies up to max. 60 °C.

The dishwasher must not be connected to open hot water appliances or instantaneous water heaters.

Permitted water pressure

Lowest permitted water pressure:

Consult your installer if the water pres-

1 bar (=10 N/cm2 =100 kPa)

sure is less than 1 bar.

Highest permitted water pressure:

In the case of a water pressure greater

10 bar (=100 N/cm2 =1 MPa)

than 10 bar, a pressure reduction valve

 

must be used (available from your

 

dealer).

 

 

 

Connect the inlet hose

1

The water inlet hose must not be kinked, crushed or entangled when it

 

is being connected up.

0Connect the threaded hose fitting (DIN 259) on the water inlet hose to a tap with an external thread (¾ inch). Tighten the threaded hose fit- ting hand tight only.

3

• In order that access to the tap in the kitchen is not limited by the use

 

of the dishwasher, we recommend the installation of an additional

tap, or fitting a two way adapter to the existing tap.

• If you need a longer water inlet hose than that supplied, VDE approved complete hose sets are to be used. These are available from your local Service Force Centre.

31

Image 31
Contents Ökofavorit Pass them on to any subsequent owner of the appliance Tips on using the applianceDear customer Please read these user instructions carefullyContents Installation and Connection Instructions General Safety Safety InstructionsInstallation, Connection and Placing into Operation Child SafetyCorrect Use Disposal of Old Appliances DisposalEconomical and Ecological Dishwashing Disposing of the Packaging MaterialAppliance Features and Control Panel Control Panel Prior to using for the first timeYour area Adjust the Water SoftenerTurning it anticlockwise Filling with Salt for the Water SoftenerFill with dishwasher salt Open the door, remove the lower RackFill with rinse aid Filling with Rinse AidOugh rinsing, spot and streak free drying Age the applianceAdjusting Rinse Aid Dosing Loading Cutlery and Dishes Daily UseLoading Cutlery Load large and heavily soiled dishes in the lower rack Loading Pans, Frying Pans and Large PlatesLoading Cups, Glasses Coffee Services Fill with detergent Filling with DetergentDetergent Recommendations Bio Wash Programmes and Concentrated DetergentsType of Soiling Selecting the Wash Programme Programme TableChanging/Interrupting the Wash Programme Starting the Wash ProgrammeChanging the wash programme Emptying the Dishwasher Switching Off the DishwasherWasher Cleaning the Filter Care and CleaningPut the flat filter back in the base Washing compartment What to do, ifStances Wrong wash programme was selected There are problems with the operation of the dish- washerWash result is unsatisfactory Dishes are still dirtyDecrease rinse aid dosing Drain hose is incorrectly laidDishes are wet and dull Rinse aid was not used Rinse aid container is emptyTechnical Data Upper basket Lower basket with cutlery basket Sample loading arrangementsFree-Standing Appliances Installing the DishwasherCannot be kinked or crushed Unscrew the screws 1 from the elbows on the back side Connect the inlet hose Connecting the DishwasherWater Connection Permitted water pressureSink outlet connection Water drainDrain hose Extension hosesAppliance is automatically pumped out Leak Prevention SystemChanging a fuse Electrical ConnectionConnections Guarantee Conditions Page Page Customer Care 08705 929Calls may be recorded for training purposes AEG Hausgeräte GmbH Postfach 90327 Nürnberg Copyright by AEG