KitchenAid KBRA20ELWH0, KBLA20ELSS0 Water Dispenser, Interior Water Filtration System, Ice Maker

Page 15

Water Dispenser

(on some models)

If you did not flush the water system when the refrigerator was first installed, dispense water into a container until you draw and discard 2 to 3 gal. (8 to 12 L) or for approximately 6 to 7 minutes after the water begins dispensing. The water you draw and discard rinses the pipes. Allow several hours for the refrigerator to cool down and chill water.

Dispensing Water

1.Hold a container under the dispenser while pressing the button.

2.Release the button to stop dispensing.

NOTE: Dispense enough water every week to maintain a fresh supply.

Interior Water Filtration System

IMPORTANT:

■You can run the water dispenser without a water filter cartridge, but your water will not be filtered. If you choose this option, replace filter with blue bypass cap.

■The interior water filter mounting bracket is located on the upper right side of the refrigerator.

■The interior water filter cartridge should be replaced every 6 months or earlier if the flow of water to your water dispenser or ice maker decreases noticeably.

Replacing the interior water filter cartridge

1.Turn used filter counterclockwise until it releases from filter head.

2.Drain water from filter into the sink, and dispose. Wipe up excess water in filter cover.

3.Remove the sealing label from end of new filter and insert into filter head. Gently rotate filter clockwise until filter stops, and snap filter cover closed.

NOTE: Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system.

4.Flush the water system by dispensing and discarding 2 to 3 gal. (8 to 12 L) of water. Cleaning the system will take approximately 6 to 7 minutes and will help clear air from the line. Additional flushing may be required in some households.

NOTE: As air is cleared from the system, water may spurt out of the dispenser.

5.Inspect the filter system for water leaks. If you see water leaks, see the “Troubleshooting” section.

Ice Maker

Turning the Ice Maker On/Off

NOTE: Do not force the wire shutoff arm up or down.

■To turn the ice maker on, simply lower the wire shutoff arm.

NOTE: Your ice maker has an automatic shutoff. As ice is made, the ice cubes will fill the ice storage bin and the ice cubes will raise the wire shutoff arm to the OFF (arm up) position.

■To manually turn the ice maker off, lift the wire shutoff arm to the OFF (arm up) position and listen for the click to make sure the ice maker will not continue to operate.

Increasing Ice Production Rate

The ice maker should produce approximately 8 to 12 batches of ice in a 24-hour period. If ice is not being made fast enough, turn the Freezer Control toward a higher (colder) number in half number steps. (For example, if the control is at 3, move it to between 3 and 4.) Wait 24 hours and, if necessary, gradually turn the Freezer Control to the highest setting, waiting 24 hours between each increase.

REMEMBER:

■Allow 24 hours to produce the first batch of ice. Discard the first three batches of ice produced.

■The quality of your ice will be only as good as the quality of the water supplied to your ice maker. Avoid connecting the ice maker to a softened water supply. Water softener chemicals (such as salt) can damage parts of the ice maker and lead to poor quality ice. If a softened water supply cannot be avoided, make sure the water softener is operating properly and is well maintained.

■Do not store anything on top of the ice maker or in the ice storage bin.

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Guide d’utilisation et d’entretien BOTTOM-MOUNT RefrigeratorRéfrigérateur Superposé Use & Care GuideTable DES Matières Table of ContentsBefore you throw away your old refrigerator or freezer Refrigerator SafetyLocation Requirements Refrigerator InstallationCleaning before use UnpackingRecommended grounding method Connecting to Water LineElectrical Requirements Water Supply ConnectionReplacing the base grille Connecting to RefrigeratorBase Grille Removing the base grilleRefrigerator Doors Final Steps Door and Hinge ReplacementDoor Reversal on some Architect Series models Door Reversal Panel SeriesArchitect Series Door Swing Reversal optionalPanel Series Door Closing and Alignment Water System PreparationDoor Closing Factory Trim Kit 20 cu. ft. Refrigerator door Dimensions for Custom Wood PanelsDimensions for Routing Door Panel Side View Normal SoundsRefrigerator USE Using the ControlsAdjusting Control Settings Mid-settingWater Dispenser Interior Water Filtration SystemIce Maker Refrigerator Features Refrigerator ShelvesMeat Drawer and Cover Utility or Egg Bin Freezer FeaturesCrisper and Crisper Cover Crisper Humidity ControlDoor Bins Door FeaturesIce Shelf Door RetainerCleaning Refrigerator CareChanging the Light Bulb Troubleshooting Power InterruptionsVacation and Moving Care Water dispenser will not operate properly Refrigerator seems to make too much noiseIce maker is not producing ice or not enough ice Off-taste, odor or gray color in the iceU.S.A Assistance Or ServiceAccessories Water Filter CertificationsCanada Application Guidelines/Water Supply Parameters Performance Data SheetsKitchenAid will not pay for Kitchenaid Refrigerator WarrantyPage Avant de jeter votre vieux réfrigérateur ou congélateur Sécurité DU RéfrigérateurNettoyage avant l’utilisation Installation DU RéfrigérateurEmplacement d’installation DéballageArrivée d’eau froide Méthode recommandée de mise à la terreSpécifications électriques Raccordement de la canalisation d’eauPour replacer la grille de la base Grille de la baseRaccordement au réfrigérateur Pour enlever la grille de la basePortes du réfrigérateur Caisse Remplacement de la porte et des charnièresInversion des portes série avec panneaux décoratifs Étapes finalesSérie Architect Inversion du sens douverture des portes optionSérie avec panneaux décoratifs Fermeture et alignement des portes Préparation du système d’eauFermeture des portes Enlèvement des panneaux de la porte Remplacement des panneaux de porteInstallation des panneaux personnalisés en bois Ensemble décoratif de l’usinePorte du réfrigérateur de 20 pi cu Dimensions pour les panneaux en bois personnalisésDimensions pour lusinage du panneau de porte vue latérale Sons normauxUtilisation des commandes Pour s’assurer d’une circulation d’air AppropriéeRéglage moyen Distribution d’eau Ajustement des réglages de commandeDistributeur d’eau Système de filtration d’eau intérieurMise en marche/arrêt de la machine à glaçons Remplacement de la cartouche de filtre à eau intérieurMachine à glaçons Tablettes du réfrigérateurTiroir à viande et couvercle Bac à légumes et couvercleRéglage de l’humidité dans le bac à Légumes Paniers de congélateurCasier utilitaire ou oeufrier Dispositif de retenue de la porte Caractéristiques DE LA PorteTablette à glaçons Balconnets dans la porteNettoyage Remplacement de l’ampoule d’éclairageRemplacement de lampoule du compartiment de réfrigération Entretien DU RéfrigérateurVacances Remplacement de lampoule du compartiment de congélationPannes de courant Entretien avant les vacances ou lors d’un DéménagementDépannage ’eau coule du distributeur Mauvais goût, odeur ou couleur grise des glaçonsLe distributeur d’eau ne fonctionne pas bien Le débit d’eau du distributeur diminue beaucoupIl existe une accumulation d’humidité à l’intérieur ’eau du distributeur n’est pas assez froideLa cloison entre les deux sections est tiède La température est trop tièdeAccessoires Assistance OU ServiceSystème de filtration d’eau intérieur Feuilles DE Données SUR LE ProduitKitchenAid ne paiera pas pour Garantie DU Réfrigérateur KitchenaidAll rights reserved 12642709SP/2225031A

KBRA20ELBL0, KBRA20EMSS, KBLA20ELSS0, KBRA20ELSS0, KBRA20ELWH0 specifications

The KitchenAid KBRA20ELBT0, along with its variants KBRA20ELWH0, KBRA20ELSS0, and KBLA20ELSS0, represents the epitome of modern refrigeration technology in bottom-mount refrigerator design. Combining style, functionality, and innovative features, these models are designed to meet the demands of contemporary kitchens while preserving food freshness and accessibility.

One of the standout features is the spacious interior layout which maximizes storage capacity. The bottom-mount design places the refrigerator section at eye level, allowing for easy access to frequently used items while the freezer section is located beneath. This configuration minimizes bending and stretching, thus enhancing convenience in day-to-day use.

Equipped with the Advanced Cooling System, the KBRA20EL series maintains optimal temperature and humidity levels. The system utilizes a combination of precise cooling technology and active temperature management to ensure that food stays fresher for longer. This technology monitors conditions within the refrigerator to minimize temperature fluctuations, which is critical for preserving perishables.

The installation of the FreshChill Temperature Management System further enhances usability by allowing users to customize the temperature settings for different compartments. Additionally, the Produce Preserver feature helps to extend the life of fruits and vegetables by absorbing ethylene gas, which can hasten spoilage.

These models feature a sleek, stainless steel exterior that not only enhances aesthetic appeal but also provides ease of cleaning. The fingerprint-resistant finish ensures that the surface remains smudge-free, which is particularly important in high-traffic kitchens.

Another valuable characteristic is the LED lighting embedded within the refrigerator compartments. This energy-efficient lighting provides bright and clear visibility, making it easy to locate items even in the back of the shelves.

Additionally, the KBRA20EL series includes multiple adjustable shelves and door bins, allowing for flexible storage solutions. The clear shelves make it easy to spot items, reducing the likelihood of food items being lost in the back of the fridge.

In essence, KitchenAid’s KBRA20ELBT0 and its counterparts showcase a sophisticated blend of advanced technology, user-friendly design, and increased storage capabilities. These bottom-mount refrigerators are an ideal choice for homeowners looking to elevate their kitchen experience while ensuring their food stays fresh and accessible. Whether it's the stylish finishes, innovative cooling technology, or versatile storage options, this series is crafted to meet the modern kitchen's needs and demands.
Top Page Image Contents