KitchenAid KBLA20ELSS0, KBRA20ELWH0, KBRA20EMSS, KBRA20ELBT0, KBRA20ELBL0 manual Refrigerator Doors

Page 7

Refrigerator Doors

Handle Removal (Architect® Series)

(Graphics are included later in this section.)

1.Using a ³⁄₃₂ in. Allen wrench, loosen the 2 set screws located on the side of each handle.

2.Pull handle straight out from the door. Make sure you keep screws for reattaching handles.

Handle Removal (Panel Series)

IMPORTANT:

■Remove door from refrigerator before removing handle.

■You must remove handles to remove decorator panels or to reverse the door swing.

1.Using a Phillips screwdriver, remove top door cap.

2.Tap bottom edge of refrigerator door handle upward with a rubber mallet.

3.Handle will slide up approximately ³⁄₄ in. (19.05 mm) and release from door.

Handle Replacement (Panel Series)

1.Make sure bottom door cap is installed.

2.Align handle notches with metal mounting tabs on side of door. Slide handle down until it locks.

3.Tap top of handle with a rubber mallet to ensure snug fit.

4.Using a Phillips screwdriver, reinstall top door cap.

Freezer Drawer Removal

(Graphics are included later in this section.)

1.Open freezer drawer to full extension.

2.Remove all articles from baskets.

3.Slide top wire basket out to full extension and lift out to remove.

4.Remove the bottom wire basket by pressing the release button on each side and lifting the basket from the rail guides.

1

1.Release button

5.Remove the Phillips screw (on some models) from each side of drawer rail assembly (see Graphic 6-1).

NOTE: Do not remove hex-head screws from rail assembly.

6.Lift front handle of freezer drawer to disengage drawer rail hooks from interior rail assembly. Lift drawer out.

Freezer Drawer Replacement

IMPORTANT: Two individuals may be required to complete this procedure.

1.Extend both interior rail assemblies to full length on each side of cabinet.

2.Locate notches in both interior rail extensions (see Graphic 6-2).

3.Align tabs on outside edge of drawer rail assemblies with notches in both rail extensions.

4.Insert tabs into notches (see Graphic 6-3).

5.Replace the Phillips screws (on some models) on both rail extensions (see Graphic 6-1).

6.Replace bottom basket by placing basket into rail guides.

7.Slide top basket into upper compartment.

Door and Hinge Removal

IMPORTANT:

■Before you begin, turn the refrigerator control OFF, unplug refrigerator or disconnect power. Remove food and any adjustable door or utility bins from doors.

■All graphics referenced in the following instructions are included later in this section after “Final Steps.”

⁵⁄₁₆" Hex-Head Top Hinge Screw

Tools Needed: ⁵⁄₁₆ in., ³⁄₈ in., ¹⁄₄ in. hex-head socket wrench, No. 2 Phillips screwdriver, and a flat-head screwdriver.

1.Keep the refrigerator door closed until you are ready to lift it free from the cabinet.

NOTE: Provide additional support for the refrigerator door while the hinges are being moved. Do not depend on the door gasket magnets to hold the door in place while you are working.

2.Remove the parts for the top hinge as shown in Top Hinge Graphic. Lift the refrigerator door free from the cabinet.

3.Remove the parts for the bottom hinge as shown in the Bottom Hinge Graphic.

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Guide d’utilisation et d’entretien BOTTOM-MOUNT RefrigeratorRéfrigérateur Superposé Use & Care GuideTable DES Matières Table of ContentsBefore you throw away your old refrigerator or freezer Refrigerator SafetyLocation Requirements Refrigerator InstallationCleaning before use UnpackingRecommended grounding method Connecting to Water LineElectrical Requirements Water Supply ConnectionReplacing the base grille Connecting to RefrigeratorBase Grille Removing the base grilleRefrigerator Doors Final Steps Door and Hinge ReplacementDoor Reversal on some Architect Series models Door Reversal Panel SeriesArchitect Series Door Swing Reversal optionalPanel Series Water System Preparation Door Closing and AlignmentDoor Closing Factory Trim Kit 20 cu. ft. Refrigerator door Dimensions for Custom Wood PanelsDimensions for Routing Door Panel Side View Normal SoundsRefrigerator USE Using the ControlsAdjusting Control Settings Mid-settingInterior Water Filtration System Water DispenserIce Maker Refrigerator Shelves Refrigerator FeaturesMeat Drawer and Cover Utility or Egg Bin Freezer FeaturesCrisper and Crisper Cover Crisper Humidity ControlDoor Bins Door FeaturesIce Shelf Door RetainerRefrigerator Care CleaningChanging the Light Bulb Power Interruptions TroubleshootingVacation and Moving Care Water dispenser will not operate properly Refrigerator seems to make too much noiseIce maker is not producing ice or not enough ice Off-taste, odor or gray color in the iceU.S.A Assistance Or ServiceWater Filter Certifications AccessoriesCanada Application Guidelines/Water Supply Parameters Performance Data SheetsKitchenAid will not pay for Kitchenaid Refrigerator WarrantyPage Avant de jeter votre vieux réfrigérateur ou congélateur Sécurité DU RéfrigérateurNettoyage avant l’utilisation Installation DU RéfrigérateurEmplacement d’installation DéballageArrivée d’eau froide Méthode recommandée de mise à la terreSpécifications électriques Raccordement de la canalisation d’eauPour replacer la grille de la base Grille de la baseRaccordement au réfrigérateur Pour enlever la grille de la basePortes du réfrigérateur Caisse Remplacement de la porte et des charnièresInversion des portes série avec panneaux décoratifs Étapes finalesSérie Architect Inversion du sens douverture des portes optionSérie avec panneaux décoratifs Préparation du système d’eau Fermeture et alignement des portesFermeture des portes Enlèvement des panneaux de la porte Remplacement des panneaux de porteInstallation des panneaux personnalisés en bois Ensemble décoratif de l’usinePorte du réfrigérateur de 20 pi cu Dimensions pour les panneaux en bois personnalisésDimensions pour lusinage du panneau de porte vue latérale Sons normauxPour s’assurer d’une circulation d’air Appropriée Utilisation des commandesRéglage moyen Distribution d’eau Ajustement des réglages de commandeDistributeur d’eau Système de filtration d’eau intérieurMise en marche/arrêt de la machine à glaçons Remplacement de la cartouche de filtre à eau intérieurMachine à glaçons Tablettes du réfrigérateurTiroir à viande et couvercle Bac à légumes et couverclePaniers de congélateur Réglage de l’humidité dans le bac à LégumesCasier utilitaire ou oeufrier Dispositif de retenue de la porte Caractéristiques DE LA PorteTablette à glaçons Balconnets dans la porteNettoyage Remplacement de l’ampoule d’éclairageRemplacement de lampoule du compartiment de réfrigération Entretien DU RéfrigérateurVacances Remplacement de lampoule du compartiment de congélationPannes de courant Entretien avant les vacances ou lors d’un DéménagementDépannage ’eau coule du distributeur Mauvais goût, odeur ou couleur grise des glaçonsLe distributeur d’eau ne fonctionne pas bien Le débit d’eau du distributeur diminue beaucoupIl existe une accumulation d’humidité à l’intérieur ’eau du distributeur n’est pas assez froideLa cloison entre les deux sections est tiède La température est trop tièdeAccessoires Assistance OU ServiceSystème de filtration d’eau intérieur Feuilles DE Données SUR LE ProduitKitchenAid ne paiera pas pour Garantie DU Réfrigérateur KitchenaidAll rights reserved 12642709SP/2225031A

KBRA20ELBL0, KBRA20EMSS, KBLA20ELSS0, KBRA20ELSS0, KBRA20ELWH0 specifications

The KitchenAid KBRA20ELBT0, along with its variants KBRA20ELWH0, KBRA20ELSS0, and KBLA20ELSS0, represents the epitome of modern refrigeration technology in bottom-mount refrigerator design. Combining style, functionality, and innovative features, these models are designed to meet the demands of contemporary kitchens while preserving food freshness and accessibility.

One of the standout features is the spacious interior layout which maximizes storage capacity. The bottom-mount design places the refrigerator section at eye level, allowing for easy access to frequently used items while the freezer section is located beneath. This configuration minimizes bending and stretching, thus enhancing convenience in day-to-day use.

Equipped with the Advanced Cooling System, the KBRA20EL series maintains optimal temperature and humidity levels. The system utilizes a combination of precise cooling technology and active temperature management to ensure that food stays fresher for longer. This technology monitors conditions within the refrigerator to minimize temperature fluctuations, which is critical for preserving perishables.

The installation of the FreshChill Temperature Management System further enhances usability by allowing users to customize the temperature settings for different compartments. Additionally, the Produce Preserver feature helps to extend the life of fruits and vegetables by absorbing ethylene gas, which can hasten spoilage.

These models feature a sleek, stainless steel exterior that not only enhances aesthetic appeal but also provides ease of cleaning. The fingerprint-resistant finish ensures that the surface remains smudge-free, which is particularly important in high-traffic kitchens.

Another valuable characteristic is the LED lighting embedded within the refrigerator compartments. This energy-efficient lighting provides bright and clear visibility, making it easy to locate items even in the back of the shelves.

Additionally, the KBRA20EL series includes multiple adjustable shelves and door bins, allowing for flexible storage solutions. The clear shelves make it easy to spot items, reducing the likelihood of food items being lost in the back of the fridge.

In essence, KitchenAid’s KBRA20ELBT0 and its counterparts showcase a sophisticated blend of advanced technology, user-friendly design, and increased storage capabilities. These bottom-mount refrigerators are an ideal choice for homeowners looking to elevate their kitchen experience while ensuring their food stays fresh and accessible. Whether it's the stylish finishes, innovative cooling technology, or versatile storage options, this series is crafted to meet the modern kitchen's needs and demands.
Top Page Image Contents