KitchenAid DHT-486XP manual Top view

Page 11

top grille assembly

decorative panel

assembly

14.Wraparound stainless steel door models: go to step 17.

Panel models: Slide decorative panel assembly up to remove from top grille assembly.

remove 2

screws

top grille decorative panel

18. If side panels are not used, go to Step 19.

If built-in area depth is 25"

(63.5 cm) or more, side panels can be installed inside the side trim or attached to the outside of the side trim.

Top view

rear wall

support board

A

side panel

B

side trim door

 

Panel

Wraparound

 

models (shown)

stainless steel

 

 

door models

A

24"

23"

 

(61 cm)

(58.4 cm)

B

24-5/8"

23-3/8"

 

(62.5 cm max.)

(59.4 cm)

 

 

 

screws

bottom grille

19. Open refrigerator doors and remove protective film from door frame. Recheck water connections at bottom of refrigerator for leaks.

Attach bottom grille to cabinet with two screws. Install shelves and bins in refrigerator and freezer compartments.

20. Set refrigerator and freezer compartment controls to the midpoint between “COLD” and “COLDEST.” Check that the compressor is operating properly and that all five lights are working.

15. Panel models: Remove screws and side trim from one side of the decorative panel. Insert your panel. Reattach side trim and screws.

16. Panel models: Slide decorative panel down to reattach to top grille.

cabinet

cabinet grille panel side trim side trim

Inside side trim piece: Slide front edge of routed side panel into trim piece. Nail rear edge of panel to support board.

NOTE: KitchenAid is not responsible for the removal or addition of molding or decorative panels that would prevent the refrigerator from being serviced.

To get the most efficient use from your new built-in refrigerator, read your KitchenAid Use and Care Guide. Keep Installation Instructions and Guide close to built-in refrigerator for easy reference.

grille panel

louver

assembly

screws

 

17. Wraparound stainless steel models: If additional ceiling clearance is required for tipping the refrigerator, the top grille and cabinet side trim can be removed. Slide the louver assembly up to remove from the top grille. Remove two screws from the grille panel and slide the grille panel down to remove from the refrigerator. Remove the screws (six each side) attaching the cabinet side trim to the refrigerator. Reassemble after dolly has been removed from refrigerator.

Part No. 2006137 Rev. A

© 1999 KitchenAid.

®Registered Trademark/Trademark of KitchenAid U.S.A., KitchenAid Canada licensee in Canada

®

HOME APPLIANCES

Prepared by KitchenAid, Benton Harbor, Michigan 49022

Printed in U.S.A.

Image 11
Contents Panel Models and Wraparound Stainless Steel Door Models Top view Product dimensionsBefore you Start Front view Side viewOpening dimensions Built-in opening requirements & dimensionsTipping radius Door swing dimensionsAnti-tip requirements Custom panels Parts thatPanel kit numbers Panel kits Extended door handle kitsEdge of panel to fit trim piece If side panel will be installed insidePanel models Side panelsAttach support board with screw Wraparound stainless steel door modelsWater supply requirements Electrical Water supply requirementsElectrical requirements Parts supplied for installation Installation Steps6 mm If doors need to be adjusted upWraparound stainless steel door models go to step Rearleveling legsTop view Avertissement Vue de dessus Dimensions du produitVue avant Vue latéraleLargeur min Caractéristiques et dimensions de la cavité d’encastrementDimensions de la cavité Taille Rayon de basculementPanneaux personnalisés Ensembles de panneauxPanneaux Numéros des ensembles Kits de poignée de porte prolongéeVue de l’extrémité de la pièce De garniture latérale Modèles à panneauxPanneaux latéraux Vue de l’extrémité côté poignée du panneau Vue latéraleModèles à portes en acier inoxydable ’électricité Spécifications de l’alimentation électriqueSpécifications de l’alimentation en eau Pose préliminaire de la canalisation d’arrivée d’eauVis Pièces fournies pour l’installationGrille de ventilation basse Sachet de pièces VirolePeut être nécessaire d’usiner le Installé à 2,5 cm 1 po au-dessus duDes portes vers la gauche ou vers la Des portes vers le haut ou vers le basVis Grille inférieure Vue de dessusMontage de la Ôter les 2 visAdvertencia Antes de Empezar DimensionesPágina Dimensiones y requerimientos para empotrarDimensiones de apertura Todas las dimensiones + 1/8 pulg mmDimensión Dimensión de puertasPreventivo de inclinación Angulo de inclinación Color Número del juego Números del juego de paneles Juegos de PanelesJuegos de manijas extendidas para puertas Paneles a medidaPaneles laterales Modelos con panelesMoldura interior Moldura exterior Del panel lateral Modelos con puertas laterales de acero inoxidableAncho y altura depende del tipo de instalación Grosor Ranura para el Listón del zócalo Si se deseaPara pre-instalar la entrada de agua Conexiones de Agua y Energía EléctricaConexiones Eléctricas Requerimiento para el Suministro de AguaRejilla de la base Bolsa con partes varias Pasos para la InstalaciónPartes suministradas para la instalación Hacia adentro o afuera, o hacia la Si es necesario ajustar las puertasRejilla inferior Corte superiorConjunto del panel Decorativo de la Rejilla superior Ilustrados De acero Inoxidable

DHT-486XP specifications

The KitchenAid DHT-486XP is a high-performance dishwasher designed to meet the needs of modern kitchens. Boasting a sleek and stylish design, it seamlessly integrates into any kitchen decor while providing powerful cleaning capabilities. Equipped with a variety of innovative features, this dishwasher simplifies the task of washing dishes, making it an essential appliance for busy households.

One of the standout features of the DHT-486XP is its advanced cleaning performance. With a robust system that includes multiple wash cycles and options, users can choose the perfect setting for their specific load. The dishwasher offers specialized cycles for heavily soiled pots and pans, delicate glassware, and even energy-saving modes for everyday use. This versatility ensures that every item comes out sparkling clean, regardless of the level of soil.

Furthermore, the DHT-486XP incorporates a unique ProWash sensor technology that automatically detects the soil level of the dishes and adjusts wash times and water usage accordingly. This intelligent feature optimizes the washing process and enhances efficiency, providing exceptional cleaning results while conserving water and energy.

Another remarkable aspect of the KitchenAid DHT-486XP is its quiet operation. With the noise-reduction technology, this dishwasher operates at remarkably low decibel levels, making it ideal for open-concept living spaces. Users can run their dishwasher at any time of day without the worry of disturbing family members or guests.

The interior design of the DHT-486XP is thoughtfully arranged to maximize space and organization. It features adjustable racks, a third rack for utensils, and fold-down tines that accommodate larger pots and pans. This design allows users to customize the loading space according to their needs, ensuring that no dish goes unwashed.

Additionally, the DHT-486XP is designed with convenience in mind. The easy-to-use control panel features a LCD display, making it simple to navigate through wash cycles and options. The dishwasher also includes a delay-start feature, which allows users to set their preferred washing time, adding to the appliance's overall flexibility.

In summary, the KitchenAid DHT-486XP is a top-tier dishwasher characterized by its advanced technology, effective cleaning performance, quiet operation, and user-friendly design. For anyone seeking a reliable and efficient dishwasher to enhance their kitchen experience, the DHT-486XP stands out as an exemplary choice.