KitchenAid 2317872A Installation Instructions, Unpack the Refrigerator, Reduce TippingRadius

Page 18

Inset Installation Dimensions

1.Measure the distance from point A (as shown) to the back wall. Add ¹⁄₃₂" (0.8 mm) to this measurement to allow the side panel to fit into the trim.

2.If the panel is more than ³⁄₈" (9.5 mm) thick, route the front edge to allow the side panel to fit into the trim.

A

Recessed Inset Installation Dimensions

1.Measure the distance from point A (as shown) to back wall.

2.Route the front edge of the support board or attach a ³⁄₈" (9.5 mm) board to hold the panel in the cabinet side trim.

A

INSTALLATION INSTRUCTIONS

Unpack the Refrigerator

WARNING

Tip Over Hazard

Refrigerator is top heavy and tips easily when not completely installed.

Keep doors taped closed until refrigerator is completely installed.

Use two or more people to move and install refrigerator.

Failure to do so can result in death or serious injury.

IMPORTANT:

■Do not remove the protective film until the refrigerator is in its operating position.

■All four leveling legs must contact the floor to support and stabilize the full weight of the refrigerator.

■Keep the cardboard shipping piece or plywood under the refrigerator until it is installed in the operating position.

1.Remove and save the literature package bag taped to the side of the refrigerator and the parts bag behind the grille. Remove the four brackets (two on each side) that attach the shipping base to the refrigerator bottom.

NOTE: Do not remove tape and door bracing until the refrigerator is in its final position.

2.If necessary, reduce the tipping radius. See “Tipping Radius” for ceiling height requirements or “Reduce Tipping Radius” for step-by-step instructions. If you do not need to reduce the tipping radius, proceed to “Move the Refrigerator into House.”

Reduce TippingRadius

(if required)

Before bringing the refrigerator into the home, be sure there is adequate ceiling height to stand the refrigerator upright. See “Tipping Radius.”

If you do not have adequate ceiling height to stand the refrigerator upright, the tipping radius can be reduced by removing the top grille and side trims (see the following chart).

Model Reduced Tipping Radius

3688" (223.5 cm)

4288¹⁄₂" (224.8 cm)

4889¹⁄₄" (226.7 cm)

Classic and Overlay Series

1.Grasp both ends of the top grille.

2.Push the top grille straight up, then pull straight out. Lay the grille on a soft surface.

BAB

A. Top grille

B. Cabinet side trim

3.Remove the six screws attaching each cabinet side trim to the refrigerator and remove the side trims.

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Table of Contents/Índice/Table des matières Side by Side BUILT-IN RefrigeratorTable of Contents ÍndiceTable DES Matières Refrigerator Safety Your safety and the safety of others are very importantModels Side by Side Non-Dispensing RefrigeratorsModels Side by Side Dispensing Refrigerators Complete SeriesToolsand Parts Installation RequirementsOpening Dimensions Location RequirementsElectrical Requirements Recommended Grounding MethodModel Width a as shown above Water Pressure Water Supply RequirementsTipping Radius Reverse Osmosis Water SupplyTop View ProductDimensionsSide View Front View Model Width a Trim edge to trim edge42 106.7 cm Models Door SwingDimensions36 91.4 cm Models 48 121.9 cm ModelsDoor Overlay SeriesDoor Panel & CabinetryClearance6.35 mm 1.3 cm 1.9 cm 5 cm OverlaySeries Custom Panelsand Handle Kits Decorative Overlay Panels ModelBacker Panels Model Classic SeriesFactory Panelsand Kits Door Panels for Non-dispenser Models ClassicSeries Custom PanelsTop Grille Panel Door Panels for Dispenser ModelsCustom Side Panels Refrigerator and Side Trim DimensionsClassic, Architect and Pro Line Series Door Panels Routing RequirementsRecessed Inset Installation Dimensions Inset Installation DimensionsFlush Installation Dimensions OverlaySeries Custom Side PanelsReduce TippingRadius Installation InstructionsUnpack the Refrigerator Classic and Overlay SeriesMove the Refrigerator into House Architect SeriesPro Line Series Style 2 Copper Line Connection Connecting to Water Line Install Anti-Tip BoardsTo Install Anti-tip Boards Connectthe Water SupplyConnecting to Refrigerator Plug in RefrigeratorMove Refrigerator to Final Location Install ClassicSeries Custom Panels Level and Align RefrigeratorDoor Panels Install OverlaySeries Custom Panels Door Panel InstallationCheck refrigerator level and adjustment. Adjust if needed Remove the handle side and top trims AdjustDoorsDoor Height Adjustment Classic and Architect ModelsDoor Swing Adjustment Install Side PanelInstall Base Grille Door-to-Door or Door-to-Refrigerator Trim AdjustmentStyle 1 Non-Dispenser Models Style 2 Dispenser Models Complete InstallationWater System Preparation Snap the skirt onto the base grilleSeguridad DEL Refrigerador Su seguridad y la seguridad de los demás es muy importanteModelos Refrigeradores de dos puertas sin despachadorRefrigeradores de dos puertas con despachador Serie CompletaRequisitosde ubicación Requisitos DE InstalaciónPiezas y Herramientas Medidas de la aberturaRequisitoseléctricos Método de conexión a tierra recomendadoModelo Anchura a como se muestra Anteriormente Presión del agua Requisitosdel suministro de aguaArco devuelco Suministro de agua de ósmosis inversaVista superior Medidas delproductoVista lateral Vista frontalMedidas de oscilación de las puertas Modelos de 36 91,4 cm Modelos de 42 106,7 cmModelos de 48 121,9 cm Puerta Posición de retención de la puerta de 90˚ Bisagra Puerta Mm más espeso que el panel recubierto de la rejilla Paneles decorativos recubiertos ModeloPaneles de soporte Modelo Soportes Paneles y juegos de fábrica delaserie ClassicAgarraderas Serie Architect AgarraderasPanel de la rejilla superior Paneles a la medida para la serie ClassicJuegos de extensión de agarraderas de puerta Paneles de puerta para modelos sin despachadorRequisitos de contorneado del panel de la rejilla superior Paneles de puerta para modelos con despachadorRequisitos de contorneado de los paneles de la puerta Agarradera común Vista superiorAdornos laterales RefrigeradorMedidas del refrigerador y del adorno lateral Medidas para la instalación empotradaPaneleslateralesa la medida para la Serie Overlay Medidas para la instalación en relieveInstrucciones DE Instalación Desempaque el refrigeradorCómoreducirelarco devuelco Cómo instalarlos tablerosantivuelco Estilo 1 Conexión de la válvula de cierre Conexión delsuministro de aguaCómo instalar los tableros antivuelco Lea todas las instrucciones antes de comenzarCómo enchufar el refrigerador Cómomover el refrigerador a su Ubicación finalConexión al refrigerador Nivelación yalineamientodel refrigerador Cómo instalar los paneles a la medida para La serie ClassicPaneles de la puerta Cómo instalar los paneles a la medida para La serie Overlay Instalación del panel de la puertaCómo ajustar la oscilación de las puertas Ajuste las puertasCómo ajustar la altura de la puerta Modelos Classic y ArchitectCómoinstalar el panellateral Cómo instalar la rejilla de la baseEstilo 1 Modelos sin despachador Cómoterminarla instalaciónPreparación delsistema de agua Estilo 2 Modelos con despachadorSécurité DU Réfrigérateur Votre sécurité et celle des autres est très importanteModèles Réfrigérateurs côte à côte sans distributeurRéfrigérateurs côte à côte avec distributeur Série ComplèteDimensions de l’ouverture Instructions D’INSTALLATIONExigences d’emplacement Outillage etpiècesMéthode recommandée de mise à la terre SpécificationsélectriquesModèle Largeur a tel quillustré ci-dessus Pression de leau Spécifications de l’alimentation en eauRayon debasculement Alimentation en eau par osmose inverseVue de dessus Dimensions du produitVue latérale Vue avant Modèle Largeur a d’un bord à l’autre de la garnitureModèles de 42 106,7 cm Dimensionspour le pivotement desportesModèles de 36 91,4 cm Modèles de 48 121,9 cmPorte Position de butée de porte à 90˚ Charnière Porte 34¹⁄₂ 87,63 cm Panneaux personnalisés et poignéesde la série OverlayPanneau décoratif Overlay Modèle Panneau d’appui ModèleEnsemblesde panneaux dorigine de La série Classic Panneau de la grille supérieure Panneaux personnalisésde la Série ClassicEnsembles de poignées de porte prolongées Panneaux de porte pour modèles sans distributeurPanneau de porte Vue latérale Exigences dusinage du panneau de la grille supérieureExigences dusinage des panneaux de porte Poignée de porte prolongée Vue supérieurePanneaux latéraux personnalisés de La Série Overlay Instructions ’INSTALLATION Déballage du réfrigérateurSéries Classic et Overlay Série Pro Line Réduction du rayon de basculementFaire entrerle réfrigérateur dans le domicile Série ArchitectRaccordement à la canalisation deau Installation de planchesantibasculementInstallation des planches antibasculement Style 1 Connexion sur robinet darrêtRaccordement au réfrigérateur Écrou de compressionDéplacementdu réfrigérateur à Lemplacement final Brancher le réfrigérateurRéglage de laplomb etalignement du Réfrigérateur Installation despanneaux personnalisés de La Série Classic Panneaux de porteInstallation des panneaux personnalisés de la Série Overlay Installation des panneaux de porteAjustement de l’ouverture des portes Ajustement desportesAjustement de la hauteur des portes Modèles Classic et ArchitectInstallation du panneau latéral Installation de la grille de la baseStyle 2 Modèles avec distributeur Acheverl’installationPréparation du système d’eau Style 1- Modèles sans distributeur

2317872A specifications

The KitchenAid 2317872A is a standout product in the realm of kitchen appliances, designed to enhance culinary experiences through innovative features and advanced technology. Renowned for its commitment to quality and durability, KitchenAid has embedded essential characteristics into the 2317872A model that cater to the diverse needs of home cooks and professional chefs alike.

One of the standout features of the KitchenAid 2317872A is its robust construction. Built with high-quality materials, it ensures reliable performance even under demanding kitchen environments. This appliance boasts a powerful motor that efficiently handles tasks such as mixing, kneading, and whipping, providing consistent results every time. Its generous capacity allows users to prepare large batches of dough or mixtures, making it perfect for family gatherings or baking marathons.

Technology plays a pivotal role in the functionality of the KitchenAid 2317872A. The appliance comes equipped with a multi-speed control that allows precise adjustments according to the needs of different recipes. Whether you're gently folding ingredients or whipping up a fluffy meringue, the variable speed options provide optimal control for every task. Additionally, the model features a unique planetary mixing action that ensures thorough blending by moving the mixing attachment around the bowl, reaching every corner for a completely incorporated mixture.

User-friendly design is another highlight of the KitchenAid 2317872A. It incorporates a tilt-head mechanism, making it easy to access the mixing bowl and change attachments. The bowl itself is crafted to hold a substantial volume of ingredients, reducing the need for constant reloading. Furthermore, this appliance is compatible with a wide range of attachments, allowing you to expand its functionality beyond mixing. From pasta makers to food grinders and spiralizers, the modular design ensures that your KitchenAid can adapt to your evolving culinary needs.

In terms of maintenance, the KitchenAid 2317872A is designed for easy cleaning. Most attachments are dishwasher-safe, and the smooth surfaces simplify the cleaning process. Its stylish design and variety of available colors make it not only a functional appliance but also an attractive addition to any kitchen decor.

In conclusion, the KitchenAid 2317872A combines durability, versatility, and user-friendly features, making it an indispensable tool for anyone looking to elevate their cooking and baking endeavors. With its state-of-the-art technologies and thoughtful design, it is a worthy investment for both casual home cooks and seasoned chefs.
Top Page Image Contents