KitchenAid 2317872A manual Installation Requirements, Toolsand Parts, Location Requirements

Page 6

INSTALLATION REQUIREMENTS

Toolsand Parts

IMPORTANT:

■Installer: Leave Installation Instructions with the homeowner.

■Homeowner: Keep Installation Instructions for future reference. Save these Installation Instructions for the local electrical inspector’s use.

TOOLS NEEDED:

Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.

■ Hand drill or electric drill

■

Torx®†T27 screwdriver

 

(properly grounded)

 

 

■

Drill bits

■

¹¹⁄₃₂" nut driver

■

Two adjustable wrenches

■

³⁄₈" and ¹⁄₂" open-end

 

 

 

wrenches

■

Phillips screwdriver

■

⁵⁄₃₂" Allen wrench

■

Small level

■

¹⁄₄" and ⁵⁄₁₆" socket drivers

■

Appliance dolly

■

Tape measure

PARTS NEEDED:

■Six #8 x 3" (7.6 cm) wood screws (longer screws may be needed)

■One or two 2" x 4" x 32" (5 cm x 10 cm x 81 cm) wood board(s)

■Order factory panels, make custom panels or consult a qualified cabinetmaker or carpenter to make the panels.

Overlay Series: Make custom panels, or consult a qualified cabinetmaker or carpenter to make the panels. See “Installation Requirements” for more information.

Architect® and Pro Line® Series are shipped complete.

■If you are connecting the water line directly to copper tubing and not to a shutoff valve, you need a ferrule, a union, and a ¹⁄₄" (6.35 mm) compression fitting.

Location Requirements

The refrigerator can be recessed in an opening between cabinets or installed at the end of a cabinet run using a side panel to enclose the refrigerator.

WARNING

Explosion Hazard

Keep flammable materials and vapors, such as gasoline, away from refrigerator.

Failure to do so can result in death, explosion, or fire.

IMPORTANT:

■Observe all governing codes and ordinances.

■It is recommended that you do not install the refrigerator near an oven, radiator, or other heat source.

■Do not install in a location where the temperature will fall below 55°F (13°C).

■Floor must support the refrigerator weight, more than 600 lbs (272 kg), door panels and contents of the refrigerator.

■Ceiling height must allow for side tipping radius. See “Tipping Radius.”

■Location should permit doors to open fully. See “Door Swing Dimensions.”

■Location must permit top grille removal. See “Opening Dimensions.”

Opening Dimensions

■To avoid tipping during use, the solid soffit must be within 1" (2.5 cm) maximum above the refrigerator. If the solid soffit is higher than 1" (2.5 cm) or one is not available, then the refrigerator must be braced.

If the anti-tip boards are needed, they must be attached to the rear wall studs 80" to 90" (203 cm to 229 cm) above the floor. See “Install Anti-Tip Boards” for more information.

NOTE: A clearance of ¹⁄₂" (1.3 cm) must be maintained above the top grille in order for the top grille to be removed.

¹⁄₂"

(1.3 cm)

†®TORX is a registered trademark of Textron Innovations Inc.

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Table of Contents/Índice/Table des matières Side by Side BUILT-IN RefrigeratorTable of Contents ÍndiceTable DES Matières Refrigerator Safety Your safety and the safety of others are very importantModels Side by Side Non-Dispensing RefrigeratorsModels Side by Side Dispensing Refrigerators Complete SeriesToolsand Parts Installation RequirementsOpening Dimensions Location RequirementsElectrical Requirements Recommended Grounding MethodModel Width a as shown above Water Pressure Water Supply RequirementsTipping Radius Reverse Osmosis Water SupplyTop View ProductDimensionsSide View Front View Model Width a Trim edge to trim edge42 106.7 cm Models Door SwingDimensions36 91.4 cm Models 48 121.9 cm ModelsDoor Overlay SeriesDoor Panel & CabinetryClearance6.35 mm 1.3 cm 1.9 cm 5 cm OverlaySeries Custom Panelsand Handle Kits Decorative Overlay Panels ModelBacker Panels Model Classic SeriesFactory Panelsand Kits Door Panels for Non-dispenser Models ClassicSeries Custom PanelsTop Grille Panel Door Panels for Dispenser ModelsCustom Side Panels Refrigerator and Side Trim DimensionsClassic, Architect and Pro Line Series Door Panels Routing RequirementsRecessed Inset Installation Dimensions Inset Installation DimensionsFlush Installation Dimensions OverlaySeries Custom Side PanelsReduce TippingRadius Installation InstructionsUnpack the Refrigerator Classic and Overlay SeriesMove the Refrigerator into House Architect SeriesPro Line Series Style 2 Copper Line Connection Connecting to Water Line Install Anti-Tip BoardsTo Install Anti-tip Boards Connectthe Water SupplyConnecting to Refrigerator Plug in RefrigeratorMove Refrigerator to Final Location Install ClassicSeries Custom Panels Level and Align RefrigeratorDoor Panels Install OverlaySeries Custom Panels Door Panel InstallationCheck refrigerator level and adjustment. Adjust if needed Remove the handle side and top trims AdjustDoorsDoor Height Adjustment Classic and Architect ModelsDoor Swing Adjustment Install Side PanelInstall Base Grille Door-to-Door or Door-to-Refrigerator Trim AdjustmentStyle 1 Non-Dispenser Models Style 2 Dispenser Models Complete InstallationWater System Preparation Snap the skirt onto the base grilleSeguridad DEL Refrigerador Su seguridad y la seguridad de los demás es muy importanteModelos Refrigeradores de dos puertas sin despachadorRefrigeradores de dos puertas con despachador Serie CompletaRequisitosde ubicación Requisitos DE InstalaciónPiezas y Herramientas Medidas de la aberturaRequisitoseléctricos Método de conexión a tierra recomendadoModelo Anchura a como se muestra Anteriormente Presión del agua Requisitosdel suministro de aguaArco devuelco Suministro de agua de ósmosis inversaVista superior Medidas delproductoVista lateral Vista frontalMedidas de oscilación de las puertas Modelos de 36 91,4 cm Modelos de 42 106,7 cmModelos de 48 121,9 cm Puerta Posición de retención de la puerta de 90˚ Bisagra Puerta Mm más espeso que el panel recubierto de la rejilla Paneles decorativos recubiertos ModeloPaneles de soporte Modelo Soportes Paneles y juegos de fábrica delaserie ClassicAgarraderas Serie Architect AgarraderasPanel de la rejilla superior Paneles a la medida para la serie ClassicJuegos de extensión de agarraderas de puerta Paneles de puerta para modelos sin despachadorRequisitos de contorneado del panel de la rejilla superior Paneles de puerta para modelos con despachadorRequisitos de contorneado de los paneles de la puerta Agarradera común Vista superiorAdornos laterales RefrigeradorMedidas del refrigerador y del adorno lateral Medidas para la instalación empotradaPaneleslateralesa la medida para la Serie Overlay Medidas para la instalación en relieveInstrucciones DE Instalación Desempaque el refrigeradorCómoreducirelarco devuelco Cómo instalarlos tablerosantivuelco Estilo 1 Conexión de la válvula de cierre Conexión delsuministro de aguaCómo instalar los tableros antivuelco Lea todas las instrucciones antes de comenzarCómo enchufar el refrigerador Cómomover el refrigerador a su Ubicación finalConexión al refrigerador Nivelación yalineamientodel refrigerador Cómo instalar los paneles a la medida para La serie ClassicPaneles de la puerta Cómo instalar los paneles a la medida para La serie Overlay Instalación del panel de la puertaCómo ajustar la oscilación de las puertas Ajuste las puertasCómo ajustar la altura de la puerta Modelos Classic y ArchitectCómoinstalar el panellateral Cómo instalar la rejilla de la baseEstilo 1 Modelos sin despachador Cómoterminarla instalaciónPreparación delsistema de agua Estilo 2 Modelos con despachadorSécurité DU Réfrigérateur Votre sécurité et celle des autres est très importanteModèles Réfrigérateurs côte à côte sans distributeurRéfrigérateurs côte à côte avec distributeur Série ComplèteDimensions de l’ouverture Instructions D’INSTALLATIONExigences d’emplacement Outillage etpiècesMéthode recommandée de mise à la terre SpécificationsélectriquesModèle Largeur a tel quillustré ci-dessus Pression de leau Spécifications de l’alimentation en eauRayon debasculement Alimentation en eau par osmose inverseVue de dessus Dimensions du produitVue latérale Vue avant Modèle Largeur a d’un bord à l’autre de la garnitureModèles de 42 106,7 cm Dimensionspour le pivotement desportesModèles de 36 91,4 cm Modèles de 48 121,9 cmPorte Position de butée de porte à 90˚ Charnière Porte 34¹⁄₂ 87,63 cm Panneaux personnalisés et poignéesde la série OverlayPanneau décoratif Overlay Modèle Panneau d’appui ModèleEnsemblesde panneaux dorigine de La série Classic Panneau de la grille supérieure Panneaux personnalisésde la Série ClassicEnsembles de poignées de porte prolongées Panneaux de porte pour modèles sans distributeurPanneau de porte Vue latérale Exigences dusinage du panneau de la grille supérieureExigences dusinage des panneaux de porte Poignée de porte prolongée Vue supérieurePanneaux latéraux personnalisés de La Série Overlay Instructions ’INSTALLATION Déballage du réfrigérateurSéries Classic et Overlay Série Pro Line Réduction du rayon de basculementFaire entrerle réfrigérateur dans le domicile Série ArchitectRaccordement à la canalisation deau Installation de planchesantibasculementInstallation des planches antibasculement Style 1 Connexion sur robinet darrêtRaccordement au réfrigérateur Écrou de compressionDéplacementdu réfrigérateur à Lemplacement final Brancher le réfrigérateurRéglage de laplomb etalignement du Réfrigérateur Installation despanneaux personnalisés de La Série Classic Panneaux de porteInstallation des panneaux personnalisés de la Série Overlay Installation des panneaux de porteAjustement de l’ouverture des portes Ajustement desportesAjustement de la hauteur des portes Modèles Classic et ArchitectInstallation du panneau latéral Installation de la grille de la baseStyle 2 Modèles avec distributeur Acheverl’installationPréparation du système d’eau Style 1- Modèles sans distributeur

2317872A specifications

The KitchenAid 2317872A is a standout product in the realm of kitchen appliances, designed to enhance culinary experiences through innovative features and advanced technology. Renowned for its commitment to quality and durability, KitchenAid has embedded essential characteristics into the 2317872A model that cater to the diverse needs of home cooks and professional chefs alike.

One of the standout features of the KitchenAid 2317872A is its robust construction. Built with high-quality materials, it ensures reliable performance even under demanding kitchen environments. This appliance boasts a powerful motor that efficiently handles tasks such as mixing, kneading, and whipping, providing consistent results every time. Its generous capacity allows users to prepare large batches of dough or mixtures, making it perfect for family gatherings or baking marathons.

Technology plays a pivotal role in the functionality of the KitchenAid 2317872A. The appliance comes equipped with a multi-speed control that allows precise adjustments according to the needs of different recipes. Whether you're gently folding ingredients or whipping up a fluffy meringue, the variable speed options provide optimal control for every task. Additionally, the model features a unique planetary mixing action that ensures thorough blending by moving the mixing attachment around the bowl, reaching every corner for a completely incorporated mixture.

User-friendly design is another highlight of the KitchenAid 2317872A. It incorporates a tilt-head mechanism, making it easy to access the mixing bowl and change attachments. The bowl itself is crafted to hold a substantial volume of ingredients, reducing the need for constant reloading. Furthermore, this appliance is compatible with a wide range of attachments, allowing you to expand its functionality beyond mixing. From pasta makers to food grinders and spiralizers, the modular design ensures that your KitchenAid can adapt to your evolving culinary needs.

In terms of maintenance, the KitchenAid 2317872A is designed for easy cleaning. Most attachments are dishwasher-safe, and the smooth surfaces simplify the cleaning process. Its stylish design and variety of available colors make it not only a functional appliance but also an attractive addition to any kitchen decor.

In conclusion, the KitchenAid 2317872A combines durability, versatility, and user-friendly features, making it an indispensable tool for anyone looking to elevate their cooking and baking endeavors. With its state-of-the-art technologies and thoughtful design, it is a worthy investment for both casual home cooks and seasoned chefs.
Top Page Image Contents