KitchenAid 2317872A manual Install OverlaySeries Custom Panels, Door Panel Installation

Page 23

4.If needed, route the door panels or install a filler panel between the doors and the decorative panels. See the “Classic Series Custom Panels” section in “Installation Requirements.”

4.Slide the backer panel into the top grille channel and reattach the end cap.

AA

A.Panels

5.Replace the door handles. Install the top screw on each handle first. Be sure that the top of both door handles are aligned.

6.If the door handles are not aligned, loosen all handle screws and adjust door handles up or down. Tighten the screws.

7.Check refrigerator level and adjustment. Adjust if needed.

Top Grille Panel

1.Grasp both ends of the top grille.

2.Push straight up, then pull straight out. Place the top grille panel-side down on a soft working surface.

BAB

A. Top grille

B. Cabinet side trim

3.Remove one end cap by loosening the nuts and sliding off the end cap.

A

 

C

 

B

 

D

 

A. Bottom rail

C. End cap

B. Nuts

D. Top rail

A

A. Backer panel

5.Replace the top grille in the cabinet side trims and pull the panel down slightly to lock it into place.

BAB

A. Top grille

B. Cabinet side trim

Install OverlaySeries Custom Panels

IMPORTANT:

Install the custom handles prior to installing the panels on the refrigerator. For more information on KitchenAid custom handle selection, refer to the KitchenAid Catalog, visit www.kitchenaid.com, or call 1-800-442-9991.

In Canada, visit www.KitchenAid.ca, or call 1-800-806-6777.

Create custom door overlay panels according to the specifications in the “Overlay Series Custom Panels” section.

KitchenAid is not responsible for the removal or addition of molding or decorative panels that would not allow access to the refrigerator for service.

Door Panel Installation

1.Remove all tape and door bracing from the refrigerator and freezer doors.

2.Open the refrigerator and freezer compartment doors.

23

Image 23
Contents Side by Side BUILT-IN Refrigerator Table of Contents/Índice/Table des matièresTable DES Matières Table of ContentsÍndice Your safety and the safety of others are very important Refrigerator SafetySide by Side Non-Dispensing Refrigerators ModelsComplete Series Models Side by Side Dispensing RefrigeratorsLocation Requirements Installation RequirementsOpening Dimensions Toolsand PartsModel Width a as shown above Electrical RequirementsRecommended Grounding Method Reverse Osmosis Water Supply Water Supply RequirementsTipping Radius Water PressureModel Width a Trim edge to trim edge ProductDimensionsSide View Front View Top View48 121.9 cm Models Door SwingDimensions36 91.4 cm Models 42 106.7 cm ModelsOverlay SeriesDoor Panel & CabinetryClearance Door6.35 mm 1.3 cm 1.9 cm 5 cm Backer Panels Model OverlaySeries Custom Panelsand Handle KitsDecorative Overlay Panels Model Classic SeriesFactory Panelsand Kits Door Panels for Dispenser Models ClassicSeries Custom PanelsTop Grille Panel Door Panels for Non-dispenser ModelsDoor Panels Routing Requirements Refrigerator and Side Trim DimensionsClassic, Architect and Pro Line Series Custom Side PanelsOverlaySeries Custom Side Panels Inset Installation DimensionsFlush Installation Dimensions Recessed Inset Installation DimensionsClassic and Overlay Series Installation InstructionsUnpack the Refrigerator Reduce TippingRadiusPro Line Series Move the Refrigerator into HouseArchitect Series Connectthe Water Supply Install Anti-Tip BoardsTo Install Anti-tip Boards Style 2 Copper Line Connection Connecting to Water LineMove Refrigerator to Final Location Connecting to RefrigeratorPlug in Refrigerator Door Panels Install ClassicSeries Custom PanelsLevel and Align Refrigerator Check refrigerator level and adjustment. Adjust if needed Install OverlaySeries Custom PanelsDoor Panel Installation Classic and Architect Models AdjustDoorsDoor Height Adjustment Remove the handle side and top trimsDoor-to-Door or Door-to-Refrigerator Trim Adjustment Install Side PanelInstall Base Grille Door Swing AdjustmentSnap the skirt onto the base grille Complete InstallationWater System Preparation Style 1 Non-Dispenser Models Style 2 Dispenser ModelsSu seguridad y la seguridad de los demás es muy importante Seguridad DEL RefrigeradorRefrigeradores de dos puertas sin despachador ModelosSerie Completa Refrigeradores de dos puertas con despachadorMedidas de la abertura Requisitos DE InstalaciónPiezas y Herramientas Requisitosde ubicaciónModelo Anchura a como se muestra Anteriormente RequisitoseléctricosMétodo de conexión a tierra recomendado Suministro de agua de ósmosis inversa Requisitosdel suministro de aguaArco devuelco Presión del aguaVista frontal Medidas delproductoVista lateral Vista superiorModelos de 48 121,9 cm Medidas de oscilación de las puertasModelos de 36 91,4 cm Modelos de 42 106,7 cm Puerta Posición de retención de la puerta de 90˚ Bisagra Puerta Paneles de soporte Modelo Mm más espeso que el panel recubierto de la rejillaPaneles decorativos recubiertos Modelo Serie Architect Agarraderas Paneles y juegos de fábrica delaserie ClassicAgarraderas SoportesPaneles de puerta para modelos sin despachador Paneles a la medida para la serie ClassicJuegos de extensión de agarraderas de puerta Panel de la rejilla superiorAgarradera común Vista superior Paneles de puerta para modelos con despachadorRequisitos de contorneado de los paneles de la puerta Requisitos de contorneado del panel de la rejilla superiorMedidas para la instalación empotrada RefrigeradorMedidas del refrigerador y del adorno lateral Adornos lateralesMedidas para la instalación en relieve Paneleslateralesa la medida para la Serie OverlayCómoreducirelarco devuelco Instrucciones DE InstalaciónDesempaque el refrigerador Cómo instalarlos tablerosantivuelco Lea todas las instrucciones antes de comenzar Conexión delsuministro de aguaCómo instalar los tableros antivuelco Estilo 1 Conexión de la válvula de cierreConexión al refrigerador Cómo enchufar el refrigeradorCómomover el refrigerador a su Ubicación final Paneles de la puerta Nivelación yalineamientodel refrigeradorCómo instalar los paneles a la medida para La serie Classic Instalación del panel de la puerta Cómo instalar los paneles a la medida para La serie OverlayModelos Classic y Architect Ajuste las puertasCómo ajustar la altura de la puerta Cómo ajustar la oscilación de las puertasCómo instalar la rejilla de la base Cómoinstalar el panellateralEstilo 2 Modelos con despachador Cómoterminarla instalaciónPreparación delsistema de agua Estilo 1 Modelos sin despachadorVotre sécurité et celle des autres est très importante Sécurité DU RéfrigérateurRéfrigérateurs côte à côte sans distributeur ModèlesSérie Complète Réfrigérateurs côte à côte avec distributeurOutillage etpièces Instructions D’INSTALLATIONExigences d’emplacement Dimensions de l’ouvertureModèle Largeur a tel quillustré ci-dessus Méthode recommandée de mise à la terreSpécificationsélectriques Alimentation en eau par osmose inverse Spécifications de l’alimentation en eauRayon debasculement Pression de leauModèle Largeur a d’un bord à l’autre de la garniture Dimensions du produitVue latérale Vue avant Vue de dessusModèles de 48 121,9 cm Dimensionspour le pivotement desportesModèles de 36 91,4 cm Modèles de 42 106,7 cmPorte Position de butée de porte à 90˚ Charnière Porte Panneau d’appui Modèle Panneaux personnalisés et poignéesde la série OverlayPanneau décoratif Overlay Modèle 34¹⁄₂ 87,63 cmEnsemblesde panneaux dorigine de La série Classic Panneaux de porte pour modèles sans distributeur Panneaux personnalisésde la Série ClassicEnsembles de poignées de porte prolongées Panneau de la grille supérieurePoignée de porte prolongée Vue supérieure Exigences dusinage du panneau de la grille supérieureExigences dusinage des panneaux de porte Panneau de porte Vue latéralePanneaux latéraux personnalisés de La Série Overlay Déballage du réfrigérateur Instructions ’INSTALLATIONSérie Architect Réduction du rayon de basculementFaire entrerle réfrigérateur dans le domicile Séries Classic et Overlay Série Pro LineStyle 1 Connexion sur robinet darrêt Installation de planchesantibasculementInstallation des planches antibasculement Raccordement à la canalisation deauÉcrou de compression Raccordement au réfrigérateurRéglage de laplomb etalignement du Réfrigérateur Déplacementdu réfrigérateur à Lemplacement finalBrancher le réfrigérateur Panneaux de porte Installation despanneaux personnalisés de La Série ClassicInstallation des panneaux de porte Installation des panneaux personnalisés de la Série OverlayModèles Classic et Architect Ajustement desportesAjustement de la hauteur des portes Ajustement de l’ouverture des portesInstallation de la grille de la base Installation du panneau latéralStyle 1- Modèles sans distributeur Acheverl’installationPréparation du système d’eau Style 2 Modèles avec distributeur

2317872A specifications

The KitchenAid 2317872A is a standout product in the realm of kitchen appliances, designed to enhance culinary experiences through innovative features and advanced technology. Renowned for its commitment to quality and durability, KitchenAid has embedded essential characteristics into the 2317872A model that cater to the diverse needs of home cooks and professional chefs alike.

One of the standout features of the KitchenAid 2317872A is its robust construction. Built with high-quality materials, it ensures reliable performance even under demanding kitchen environments. This appliance boasts a powerful motor that efficiently handles tasks such as mixing, kneading, and whipping, providing consistent results every time. Its generous capacity allows users to prepare large batches of dough or mixtures, making it perfect for family gatherings or baking marathons.

Technology plays a pivotal role in the functionality of the KitchenAid 2317872A. The appliance comes equipped with a multi-speed control that allows precise adjustments according to the needs of different recipes. Whether you're gently folding ingredients or whipping up a fluffy meringue, the variable speed options provide optimal control for every task. Additionally, the model features a unique planetary mixing action that ensures thorough blending by moving the mixing attachment around the bowl, reaching every corner for a completely incorporated mixture.

User-friendly design is another highlight of the KitchenAid 2317872A. It incorporates a tilt-head mechanism, making it easy to access the mixing bowl and change attachments. The bowl itself is crafted to hold a substantial volume of ingredients, reducing the need for constant reloading. Furthermore, this appliance is compatible with a wide range of attachments, allowing you to expand its functionality beyond mixing. From pasta makers to food grinders and spiralizers, the modular design ensures that your KitchenAid can adapt to your evolving culinary needs.

In terms of maintenance, the KitchenAid 2317872A is designed for easy cleaning. Most attachments are dishwasher-safe, and the smooth surfaces simplify the cleaning process. Its stylish design and variety of available colors make it not only a functional appliance but also an attractive addition to any kitchen decor.

In conclusion, the KitchenAid 2317872A combines durability, versatility, and user-friendly features, making it an indispensable tool for anyone looking to elevate their cooking and baking endeavors. With its state-of-the-art technologies and thoughtful design, it is a worthy investment for both casual home cooks and seasoned chefs.