KitchenAid 2317872A manual Plug in Refrigerator, Move Refrigerator to Final Location

Page 21

5.Using a grounded drill, drill a ¹⁄₄" (6.35 mm) hole in the cold water pipe you have selected.

 

A

G

B

 

 

C

F E

D

A. Cold water pipe

E. Compression sleeve

B. Pipe clamp

F. Shutoff valve

C. Copper tubing

G. Packing nut

D. Compression nut

 

6.Fasten the shutoff valve to the cold water pipe with the pipe clamp. Be sure the outlet end is solidly in the ¹⁄₄" (6.35 mm) drilled hole in the water pipe and that the washer is under the pipe clamp. Tighten the packing nut. Tighten the pipe clamp screws slowly and evenly so washer makes a watertight seal. Do not overtighten, or you may crush the copper tubing.

7.Slip the compression sleeve and compression nut on the copper tubing as shown. Insert the end of the tubing into the outlet end squarely as far as it will go. Screw compression nut onto outlet end with adjustable wrench. Do not overtighten the clamp or the sleeve. This will crush the copper tubing.

IMPORTANT: Before attaching the tubing to shutoff valve, flush the main water supply line to remove particles and air in the water line. Allow enough flow so that water becomes clear. Flushing the water line may help avoid filters and/or water valves from becoming clogged.

8.Turn off the shutoff valve on the water pipe. Coil the copper tubing.

9.Check for leaks around the saddle valve.

Connecting to Refrigerator

1.Unplug the refrigerator or disconnect power.

2.Remove the shipping tape from the gray, coiled water tubing on the rear of the refrigerator.

3.Measure the distance from the shutoff valve to the opening in which the refrigerator will be located. Tubing must be extended from the shutoff valve into the refrigerator opening following specific guidelines. See “Water Supply Requirements.”

4.A ¹⁄₄" x ¹⁄₄" (6.35 mm to 6.35 mm) coupling is needed in order to connect the water tubing to an existing household water line. Thread the provided nut onto the coupling on the end of the copper tubing.

A

B

C

D

E F G

A. Water tubing

 

 

E. Ferrule (purchased)

B. Nut

 

 

F. Nut (purchased)

C. Bulb

 

 

G. Household water line (as

D. Coupling (purchased)

 

connected in previous section)

5.Turn shutoff valve ON.

6.Check for leaks. Tighten any nuts or connections (including connections at the valve) that leak.

7.Plug in the refrigerator or reconnect power.

8.Flush the water system. See “Water System Preparation.”

NOTE: Allow 24 hours to produce the first batch of ice. Discard the first three batches of ice produced. Allow 3 days to completely fill ice container.

Plug in Refrigerator

WARNING

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death, fire, or electrical shock.

1.Set control switch at top of cabinet to the OFF position.

2.Plug into a grounded 3 prong outlet.

Move Refrigerator to Final Location

WARNING

Tip Over Hazard

Refrigerator is top heavy and tips easily when not completely installed.

Keep doors taped closed until refrigerator is completely installed.

Use two or more people to move and install refrigerator.

Failure to do so can result in death or serious injury.

IMPORTANT: To avoid floor damage, make sure levelers are raised (not touching floor) and refrigerator is on rollers before moving.

1.Place top of cardboard carton or plywood under refrigerator. Remove dolly.

2.Do not remove protective film or cover.

3.Move the refrigerator straight back and evenly into the opening. Be sure that the refrigerator side trims are not interfering with the door opening. Also, be sure that the water tubing is not kinked and the power supply cord is on top of the refrigerator.

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Side by Side BUILT-IN Refrigerator Table of Contents/Índice/Table des matièresTable of Contents ÍndiceTable DES Matières Your safety and the safety of others are very important Refrigerator SafetySide by Side Non-Dispensing Refrigerators ModelsComplete Series Models Side by Side Dispensing RefrigeratorsOpening Dimensions Installation RequirementsToolsand Parts Location RequirementsElectrical Requirements Recommended Grounding MethodModel Width a as shown above Tipping Radius Water Supply RequirementsWater Pressure Reverse Osmosis Water SupplySide View Front View ProductDimensionsTop View Model Width a Trim edge to trim edge36 91.4 cm Models Door SwingDimensions42 106.7 cm Models 48 121.9 cm ModelsOverlay SeriesDoor Panel & CabinetryClearance Door6.35 mm 1.3 cm 1.9 cm 5 cm OverlaySeries Custom Panelsand Handle Kits Decorative Overlay Panels ModelBacker Panels Model Classic SeriesFactory Panelsand Kits Top Grille Panel ClassicSeries Custom PanelsDoor Panels for Non-dispenser Models Door Panels for Dispenser ModelsClassic, Architect and Pro Line Series Refrigerator and Side Trim DimensionsCustom Side Panels Door Panels Routing RequirementsFlush Installation Dimensions Inset Installation DimensionsRecessed Inset Installation Dimensions OverlaySeries Custom Side PanelsUnpack the Refrigerator Installation InstructionsReduce TippingRadius Classic and Overlay SeriesMove the Refrigerator into House Architect SeriesPro Line Series To Install Anti-tip Boards Install Anti-Tip BoardsStyle 2 Copper Line Connection Connecting to Water Line Connectthe Water SupplyConnecting to Refrigerator Plug in RefrigeratorMove Refrigerator to Final Location Install ClassicSeries Custom Panels Level and Align RefrigeratorDoor Panels Install OverlaySeries Custom Panels Door Panel InstallationCheck refrigerator level and adjustment. Adjust if needed Door Height Adjustment AdjustDoorsRemove the handle side and top trims Classic and Architect ModelsInstall Base Grille Install Side PanelDoor Swing Adjustment Door-to-Door or Door-to-Refrigerator Trim AdjustmentWater System Preparation Complete InstallationStyle 1 Non-Dispenser Models Style 2 Dispenser Models Snap the skirt onto the base grilleSu seguridad y la seguridad de los demás es muy importante Seguridad DEL RefrigeradorRefrigeradores de dos puertas sin despachador ModelosSerie Completa Refrigeradores de dos puertas con despachadorPiezas y Herramientas Requisitos DE InstalaciónRequisitosde ubicación Medidas de la aberturaRequisitoseléctricos Método de conexión a tierra recomendadoModelo Anchura a como se muestra Anteriormente Arco devuelco Requisitosdel suministro de aguaPresión del agua Suministro de agua de ósmosis inversaVista lateral Medidas delproductoVista superior Vista frontalMedidas de oscilación de las puertas Modelos de 36 91,4 cm Modelos de 42 106,7 cmModelos de 48 121,9 cm Puerta Posición de retención de la puerta de 90˚ Bisagra Puerta Mm más espeso que el panel recubierto de la rejilla Paneles decorativos recubiertos ModeloPaneles de soporte Modelo Agarraderas Paneles y juegos de fábrica delaserie ClassicSoportes Serie Architect AgarraderasJuegos de extensión de agarraderas de puerta Paneles a la medida para la serie ClassicPanel de la rejilla superior Paneles de puerta para modelos sin despachadorRequisitos de contorneado de los paneles de la puerta Paneles de puerta para modelos con despachadorRequisitos de contorneado del panel de la rejilla superior Agarradera común Vista superiorMedidas del refrigerador y del adorno lateral RefrigeradorAdornos laterales Medidas para la instalación empotradaMedidas para la instalación en relieve Paneleslateralesa la medida para la Serie OverlayInstrucciones DE Instalación Desempaque el refrigeradorCómoreducirelarco devuelco Cómo instalarlos tablerosantivuelco Cómo instalar los tableros antivuelco Conexión delsuministro de aguaEstilo 1 Conexión de la válvula de cierre Lea todas las instrucciones antes de comenzarCómo enchufar el refrigerador Cómomover el refrigerador a su Ubicación finalConexión al refrigerador Nivelación yalineamientodel refrigerador Cómo instalar los paneles a la medida para La serie ClassicPaneles de la puerta Instalación del panel de la puerta Cómo instalar los paneles a la medida para La serie OverlayCómo ajustar la altura de la puerta Ajuste las puertasCómo ajustar la oscilación de las puertas Modelos Classic y ArchitectCómo instalar la rejilla de la base Cómoinstalar el panellateralPreparación delsistema de agua Cómoterminarla instalaciónEstilo 1 Modelos sin despachador Estilo 2 Modelos con despachadorVotre sécurité et celle des autres est très importante Sécurité DU RéfrigérateurRéfrigérateurs côte à côte sans distributeur ModèlesSérie Complète Réfrigérateurs côte à côte avec distributeurExigences d’emplacement Instructions D’INSTALLATIONDimensions de l’ouverture Outillage etpiècesMéthode recommandée de mise à la terre SpécificationsélectriquesModèle Largeur a tel quillustré ci-dessus Rayon debasculement Spécifications de l’alimentation en eauPression de leau Alimentation en eau par osmose inverseVue latérale Vue avant Dimensions du produitVue de dessus Modèle Largeur a d’un bord à l’autre de la garnitureModèles de 36 91,4 cm Dimensionspour le pivotement desportesModèles de 42 106,7 cm Modèles de 48 121,9 cmPorte Position de butée de porte à 90˚ Charnière Porte Panneau décoratif Overlay Modèle Panneaux personnalisés et poignéesde la série Overlay34¹⁄₂ 87,63 cm Panneau d’appui ModèleEnsemblesde panneaux dorigine de La série Classic Ensembles de poignées de porte prolongées Panneaux personnalisésde la Série ClassicPanneau de la grille supérieure Panneaux de porte pour modèles sans distributeurExigences dusinage des panneaux de porte Exigences dusinage du panneau de la grille supérieurePanneau de porte Vue latérale Poignée de porte prolongée Vue supérieurePanneaux latéraux personnalisés de La Série Overlay Déballage du réfrigérateur Instructions ’INSTALLATIONFaire entrerle réfrigérateur dans le domicile Réduction du rayon de basculementSéries Classic et Overlay Série Pro Line Série ArchitectInstallation des planches antibasculement Installation de planchesantibasculementRaccordement à la canalisation deau Style 1 Connexion sur robinet darrêtÉcrou de compression Raccordement au réfrigérateurDéplacementdu réfrigérateur à Lemplacement final Brancher le réfrigérateurRéglage de laplomb etalignement du Réfrigérateur Panneaux de porte Installation despanneaux personnalisés de La Série ClassicInstallation des panneaux de porte Installation des panneaux personnalisés de la Série OverlayAjustement de la hauteur des portes Ajustement desportesAjustement de l’ouverture des portes Modèles Classic et ArchitectInstallation de la grille de la base Installation du panneau latéralPréparation du système d’eau Acheverl’installationStyle 2 Modèles avec distributeur Style 1- Modèles sans distributeur

2317872A specifications

The KitchenAid 2317872A is a standout product in the realm of kitchen appliances, designed to enhance culinary experiences through innovative features and advanced technology. Renowned for its commitment to quality and durability, KitchenAid has embedded essential characteristics into the 2317872A model that cater to the diverse needs of home cooks and professional chefs alike.

One of the standout features of the KitchenAid 2317872A is its robust construction. Built with high-quality materials, it ensures reliable performance even under demanding kitchen environments. This appliance boasts a powerful motor that efficiently handles tasks such as mixing, kneading, and whipping, providing consistent results every time. Its generous capacity allows users to prepare large batches of dough or mixtures, making it perfect for family gatherings or baking marathons.

Technology plays a pivotal role in the functionality of the KitchenAid 2317872A. The appliance comes equipped with a multi-speed control that allows precise adjustments according to the needs of different recipes. Whether you're gently folding ingredients or whipping up a fluffy meringue, the variable speed options provide optimal control for every task. Additionally, the model features a unique planetary mixing action that ensures thorough blending by moving the mixing attachment around the bowl, reaching every corner for a completely incorporated mixture.

User-friendly design is another highlight of the KitchenAid 2317872A. It incorporates a tilt-head mechanism, making it easy to access the mixing bowl and change attachments. The bowl itself is crafted to hold a substantial volume of ingredients, reducing the need for constant reloading. Furthermore, this appliance is compatible with a wide range of attachments, allowing you to expand its functionality beyond mixing. From pasta makers to food grinders and spiralizers, the modular design ensures that your KitchenAid can adapt to your evolving culinary needs.

In terms of maintenance, the KitchenAid 2317872A is designed for easy cleaning. Most attachments are dishwasher-safe, and the smooth surfaces simplify the cleaning process. Its stylish design and variety of available colors make it not only a functional appliance but also an attractive addition to any kitchen decor.

In conclusion, the KitchenAid 2317872A combines durability, versatility, and user-friendly features, making it an indispensable tool for anyone looking to elevate their cooking and baking endeavors. With its state-of-the-art technologies and thoughtful design, it is a worthy investment for both casual home cooks and seasoned chefs.
Top Page Image Contents