KitchenAid 2317872A manual Install Side Panel, Install Base Grille, Door Swing Adjustment

Page 25

4.After adjusting, check the doors to make sure they are even at the top and bottom. If the doors are not even, continue to turn the bushing to adjust the door height.

5.Replace the locking plate.

6.Turn the bushing slightly to align the hinge and locking plate screw holes.

7.Replace the door stop screw or screws and tighten.

IMPORTANT: Do not place the door stop screw in the 130° position on Overlay Series models unless the custom panels have been routed on the hinge side. See “Overlay Series Door Panel & Cabinetry Clearance.”

8.Make final recheck to make sure the doors are aligned and even.

Door Swing Adjustment

1.Check that the refrigerator door can open freely. If the door opens too wide, remove the door stop screw or screws (depending on your model) from the bottom hinge. See “Door Height Adjustment” earlier in this section.

2.Hold the door open to a position that is less than 90°.

3.Replace the door stop screw or screws in the bottom hinge and tighten.

Install Side Panel

If the built-in area depth is 25" (63.5 cm) or more, the side panels can be installed inside the side trim or attached to the outside of the side trim.

IMPORTANT: KitchenAid is not responsible for the removal or addition of molding or decorative panels that would not allow access to the refrigerator for service.

1.For the inside side trim piece, slide the front edge of the routed side panel into the trim piece.

2.Nail the rear edge of the panel to the support board.

A

A B C

A.130°

B.110° (Overlay series)

C.90°

Door-to-Door or Door-to-Refrigerator Trim Adjustment

1.Loosen, but do not remove, the four Torx®† 27 flat-head mounting screws and the two ¹⁄₄" hex-head mounting screws.

2.Adjust the top hinge of either door to align it with the other door or the refrigerator trim.

3.Tighten the four Torx®† 27 flat-head mounting screws to a torque of approximately 100 inch-pounds (11.3 Nm) and tighten the two ¹⁄₄" hex-head mounting screws.

A

B

B

A. Support board (mounted to back wall)

B. Cab side trim

Install Base Grille

There are two pieces to the base grille to allow for a custom fit: the base grille itself and the skirt. The skirt can be added to the base grille in order to extend it all the way to the floor.

1.To see if the skirt is needed, place the base grille into position. Do not attach the base grille to the refrigerator. Measure the distance between the bottom of the base grille and the floor. The gap must be a minimum of ¹⁄₂" (1.27 cm) in order to add the skirt.

NOTE: If the gap measures less than ¹⁄₂" (1.27 cm), skip steps 3 and 4 of the instructions, and install the base grille only.

2.Remove the protective film from the base grille.

A.Torx® 27 flat-head mounting screws

B.¹⁄₄" hex-head mounting screws

†®TORX is a registered trademark of Textron Innovations Inc.

25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents Side by Side BUILT-IN Refrigerator Table of Contents/Índice/Table des matièresÍndice Table of ContentsTable DES Matières Your safety and the safety of others are very important Refrigerator SafetySide by Side Non-Dispensing Refrigerators ModelsComplete Series Models Side by Side Dispensing RefrigeratorsOpening Dimensions Installation RequirementsToolsand Parts Location RequirementsRecommended Grounding Method Electrical RequirementsModel Width a as shown above Tipping Radius Water Supply RequirementsWater Pressure Reverse Osmosis Water SupplySide View Front View ProductDimensionsTop View Model Width a Trim edge to trim edge36 91.4 cm Models Door SwingDimensions42 106.7 cm Models 48 121.9 cm ModelsOverlay SeriesDoor Panel & CabinetryClearance Door6.35 mm 1.3 cm 1.9 cm 5 cm Decorative Overlay Panels Model OverlaySeries Custom Panelsand Handle KitsBacker Panels Model Classic SeriesFactory Panelsand Kits Top Grille Panel ClassicSeries Custom PanelsDoor Panels for Non-dispenser Models Door Panels for Dispenser ModelsClassic, Architect and Pro Line Series Refrigerator and Side Trim DimensionsCustom Side Panels Door Panels Routing RequirementsFlush Installation Dimensions Inset Installation DimensionsRecessed Inset Installation Dimensions OverlaySeries Custom Side PanelsUnpack the Refrigerator Installation InstructionsReduce TippingRadius Classic and Overlay SeriesArchitect Series Move the Refrigerator into HousePro Line Series To Install Anti-tip Boards Install Anti-Tip BoardsStyle 2 Copper Line Connection Connecting to Water Line Connectthe Water SupplyPlug in Refrigerator Connecting to RefrigeratorMove Refrigerator to Final Location Level and Align Refrigerator Install ClassicSeries Custom PanelsDoor Panels Door Panel Installation Install OverlaySeries Custom PanelsCheck refrigerator level and adjustment. Adjust if needed Door Height Adjustment AdjustDoorsRemove the handle side and top trims Classic and Architect ModelsInstall Base Grille Install Side PanelDoor Swing Adjustment Door-to-Door or Door-to-Refrigerator Trim AdjustmentWater System Preparation Complete InstallationStyle 1 Non-Dispenser Models Style 2 Dispenser Models Snap the skirt onto the base grilleSu seguridad y la seguridad de los demás es muy importante Seguridad DEL RefrigeradorRefrigeradores de dos puertas sin despachador ModelosSerie Completa Refrigeradores de dos puertas con despachadorPiezas y Herramientas Requisitos DE InstalaciónRequisitosde ubicación Medidas de la aberturaMétodo de conexión a tierra recomendado RequisitoseléctricosModelo Anchura a como se muestra Anteriormente Arco devuelco Requisitosdel suministro de aguaPresión del agua Suministro de agua de ósmosis inversaVista lateral Medidas delproductoVista superior Vista frontalModelos de 36 91,4 cm Modelos de 42 106,7 cm Medidas de oscilación de las puertasModelos de 48 121,9 cm Puerta Posición de retención de la puerta de 90˚ Bisagra Puerta Paneles decorativos recubiertos Modelo Mm más espeso que el panel recubierto de la rejillaPaneles de soporte Modelo Agarraderas Paneles y juegos de fábrica delaserie ClassicSoportes Serie Architect AgarraderasJuegos de extensión de agarraderas de puerta Paneles a la medida para la serie ClassicPanel de la rejilla superior Paneles de puerta para modelos sin despachadorRequisitos de contorneado de los paneles de la puerta Paneles de puerta para modelos con despachadorRequisitos de contorneado del panel de la rejilla superior Agarradera común Vista superiorMedidas del refrigerador y del adorno lateral RefrigeradorAdornos laterales Medidas para la instalación empotradaMedidas para la instalación en relieve Paneleslateralesa la medida para la Serie OverlayDesempaque el refrigerador Instrucciones DE InstalaciónCómoreducirelarco devuelco Cómo instalarlos tablerosantivuelco Cómo instalar los tableros antivuelco Conexión delsuministro de aguaEstilo 1 Conexión de la válvula de cierre Lea todas las instrucciones antes de comenzarCómomover el refrigerador a su Ubicación final Cómo enchufar el refrigeradorConexión al refrigerador Cómo instalar los paneles a la medida para La serie Classic Nivelación yalineamientodel refrigeradorPaneles de la puerta Instalación del panel de la puerta Cómo instalar los paneles a la medida para La serie OverlayCómo ajustar la altura de la puerta Ajuste las puertasCómo ajustar la oscilación de las puertas Modelos Classic y ArchitectCómo instalar la rejilla de la base Cómoinstalar el panellateralPreparación delsistema de agua Cómoterminarla instalaciónEstilo 1 Modelos sin despachador Estilo 2 Modelos con despachadorVotre sécurité et celle des autres est très importante Sécurité DU RéfrigérateurRéfrigérateurs côte à côte sans distributeur ModèlesSérie Complète Réfrigérateurs côte à côte avec distributeurExigences d’emplacement Instructions D’INSTALLATIONDimensions de l’ouverture Outillage etpiècesSpécificationsélectriques Méthode recommandée de mise à la terreModèle Largeur a tel quillustré ci-dessus Rayon debasculement Spécifications de l’alimentation en eauPression de leau Alimentation en eau par osmose inverseVue latérale Vue avant Dimensions du produitVue de dessus Modèle Largeur a d’un bord à l’autre de la garnitureModèles de 36 91,4 cm Dimensionspour le pivotement desportesModèles de 42 106,7 cm Modèles de 48 121,9 cmPorte Position de butée de porte à 90˚ Charnière Porte Panneau décoratif Overlay Modèle Panneaux personnalisés et poignéesde la série Overlay34¹⁄₂ 87,63 cm Panneau d’appui ModèleEnsemblesde panneaux dorigine de La série Classic Ensembles de poignées de porte prolongées Panneaux personnalisésde la Série ClassicPanneau de la grille supérieure Panneaux de porte pour modèles sans distributeurExigences dusinage des panneaux de porte Exigences dusinage du panneau de la grille supérieurePanneau de porte Vue latérale Poignée de porte prolongée Vue supérieurePanneaux latéraux personnalisés de La Série Overlay Déballage du réfrigérateur Instructions ’INSTALLATIONFaire entrerle réfrigérateur dans le domicile Réduction du rayon de basculementSéries Classic et Overlay Série Pro Line Série ArchitectInstallation des planches antibasculement Installation de planchesantibasculementRaccordement à la canalisation deau Style 1 Connexion sur robinet darrêtÉcrou de compression Raccordement au réfrigérateurBrancher le réfrigérateur Déplacementdu réfrigérateur à Lemplacement finalRéglage de laplomb etalignement du Réfrigérateur Panneaux de porte Installation despanneaux personnalisés de La Série ClassicInstallation des panneaux de porte Installation des panneaux personnalisés de la Série OverlayAjustement de la hauteur des portes Ajustement desportesAjustement de l’ouverture des portes Modèles Classic et ArchitectInstallation de la grille de la base Installation du panneau latéralPréparation du système d’eau Acheverl’installationStyle 2 Modèles avec distributeur Style 1- Modèles sans distributeur

2317872A specifications

The KitchenAid 2317872A is a standout product in the realm of kitchen appliances, designed to enhance culinary experiences through innovative features and advanced technology. Renowned for its commitment to quality and durability, KitchenAid has embedded essential characteristics into the 2317872A model that cater to the diverse needs of home cooks and professional chefs alike.

One of the standout features of the KitchenAid 2317872A is its robust construction. Built with high-quality materials, it ensures reliable performance even under demanding kitchen environments. This appliance boasts a powerful motor that efficiently handles tasks such as mixing, kneading, and whipping, providing consistent results every time. Its generous capacity allows users to prepare large batches of dough or mixtures, making it perfect for family gatherings or baking marathons.

Technology plays a pivotal role in the functionality of the KitchenAid 2317872A. The appliance comes equipped with a multi-speed control that allows precise adjustments according to the needs of different recipes. Whether you're gently folding ingredients or whipping up a fluffy meringue, the variable speed options provide optimal control for every task. Additionally, the model features a unique planetary mixing action that ensures thorough blending by moving the mixing attachment around the bowl, reaching every corner for a completely incorporated mixture.

User-friendly design is another highlight of the KitchenAid 2317872A. It incorporates a tilt-head mechanism, making it easy to access the mixing bowl and change attachments. The bowl itself is crafted to hold a substantial volume of ingredients, reducing the need for constant reloading. Furthermore, this appliance is compatible with a wide range of attachments, allowing you to expand its functionality beyond mixing. From pasta makers to food grinders and spiralizers, the modular design ensures that your KitchenAid can adapt to your evolving culinary needs.

In terms of maintenance, the KitchenAid 2317872A is designed for easy cleaning. Most attachments are dishwasher-safe, and the smooth surfaces simplify the cleaning process. Its stylish design and variety of available colors make it not only a functional appliance but also an attractive addition to any kitchen decor.

In conclusion, the KitchenAid 2317872A combines durability, versatility, and user-friendly features, making it an indispensable tool for anyone looking to elevate their cooking and baking endeavors. With its state-of-the-art technologies and thoughtful design, it is a worthy investment for both casual home cooks and seasoned chefs.
Top Page Image Contents