KitchenAid LI3ZGC/W10320581E Install Range Hood, Install Vent System, For vented installations

Page 10

4.Use saber or keyhole saw to cut the circular vent opening.

Circular vent opening

*5"

(12.7 cm)

Cabinet cutouts

*From wall, not cabinet frame

Install Vent System

1.Install vent through the vent opening in upper cabinet or wall. Complete venting system according to the selected venting method. See “Venting Requirements” section.

2.Use caulking to seal exterior wall or roof opening around the cap.

Install Range Hood

1.Remove the grease filters. See the “Range Hood Care” section.

2.Remove mounting screws and lateral supports.

A

A

B

A. Lateral supports

B. Mounting screws

For vented installations:

Depending on your installation, remove either top or rear rectangular vent knockout.

NOTE: Do not remove rectangular knockouts if installation of range hood is to be non-venting (recirculating).

Make sure damper pivot is nearest to top/back edge of range hood.

Remove tape from damper flap.

NOTE: The exhaust adapter/damper can be installed up to 1" (2.5 cm) on either side of the hood center to accommodate off-center ductwork.

If using rectangular vent, attach rectangular damper/vent connectors to the range hood using sheet metal screws.

A

B

 

 

C

 

D

E

 

B

A. Vertical vent

C. Hinge pin

B. Sheet metal screws

D. Vent knockouts

 

E. Horizontal vent

If using round vent, attach vent transition piece (purchased separately) to range hood top using sheet metal screws.

NOTE: If the wall cap is directly behind the vent connector, the dampers in the connector and wall cap must not interfere with each other. Remove the vent connector damper if they interfere.

3.Lift the range hood up under cabinet and determine final location by centering beneath cabinet. Mark on the underside of cabinet the location of the 4 keyhole mounting slots on the range hood. Set range hood aside on a covered surface.

A

A. Keyhole slot

4.Use ¹⁄₈" (3 mm) drill bit and drill 4 pilot holes as shown.

A

A. Drill pilot hole

5.Install the 4 - 4.5 x 13 mm mounting screws in pilot holes. Leave about ¹⁄₄" (6.4 mm) space between screw heads and cabinet to slide range hood into place.

¹⁄₄"

(6.4 mm)

10

Image 10
Contents Hotte DE Cuisinière Table of Contents Table DES MatièresRange Hood Safety Your safety and the safety of others are very importantImportant Safety Instructions Tools and Parts Installation RequirementsLocation Requirements Venting Requirements Installation ClearancesCold Weather Installations Makeup AirExample vent system Calculating Vent System LengthCm or Larger Round Vent System ¹⁄₄ x 10 8.3 cm x 25.4 cm Vent SystemElectrical Requirements Installation InstructionsDetermine Wiring Hole Location Prepare LocationWall Venting To wire through topTo wire through wall To make a 3¹⁄₂ x 10½ 8.9 cm x 26.7 cm rectangle in the wallInstall Vent System Install Range HoodFor vented installations Remove the vent knockout from the front mounting plate For Vented Installations Only Complete InstallationMake Electrical Connection Display Range Hood USELight Cleaning TimerRange Hood Care To Replace Charcoal Filter Non-Vented Recirculating Installation FiltersReplacing a Halogen Lamp Wiring Diagram Gnd L NeuU.S.A Assistance or ServiceAccessories CanadaKitchenaid Ventilation Warranty This limited warranty does not coverSécurité DE LA Hotte DE Cuisinière Votre sécurité et celle des autres est très importanteImportantes Instructions DE Sécurité Exigences d’emplacement Exigences D’INSTALLATIONOutils et pièces Distances de dégagement à respecter Installations pour régions à climat froidExigences concernant l’évacuation Air d’appointSystème de décharge circulaire de 6 15,2 cm ou plus Méthodes d’évacuationCalcul de la longueur effective du circuit d’évacuation Exemple de système de déchargeSystème de décharge de 3¹⁄₄ x 10 8,3 cm x 25,4 cm Longueur maximale recommandée = 35 pi 10,7 mSpécifications électriques ComposantDéterminer l’emplacement du trou de passage du câble Instructions D’INSTALLATIONPréparation de l’emplacement Câblage à travers le sommet du placardÉvacuation par le mur Installation du système d’évacuation Installation de la hotteInstallations avec décharge à l’extérieur Retirer les vis et le support arrière Installations avec décharge à l’extérieur seulement Achever l’installationRaccordement électrique Utilisation DE LA Hotte Tableau de commandeActivation et désactivation du signal sonore AffichageMinuterie ÉclairageVitesse du ventilateur Entretien DE LA Hotte NettoyageSchéma DE Câblage Terre L NeuAccessoires Assistance OU ServiceAu Canada Garantie DU Système DE Ventilation Kitchenaid La présente garantie limitée ne couvre pasW10320581E

LI3ZGC/W10320581E specifications

The KitchenAid LI3ZGC/W10320581E is a versatile and efficient appliance that enhances the culinary experience for home chefs. With its sleek design and powerful capabilities, this kitchen tool stands out in any kitchen setting. One of the main features is its powerful motor, designed to handle a range of mixing tasks with ease. Whether you are kneading bread dough or whipping cream, the LI3ZGC combines efficiency with performance, ensuring consistent results every time.

One of the key technologies integrated into the KitchenAid LI3ZGC is its advanced planetary mixing action. This innovative system allows the mixing attachment to rotate around the bowl, while also spinning on its own axis. This unique motion ensures that all ingredients are thoroughly mixed, eliminating the need to scrape down the bowl frequently. This feature not only saves time but also enhances the quality of the final product.

Another standout characteristic of the LI3ZGC is its robust construction, designed for durability and longevity. Made from high-quality materials, this appliance can withstand heavy usage, making it ideal for both everyday cooking and special occasions. The sturdy design provides stability during operation, preventing any unwanted movement or slipping.

Additionally, the KitchenAid LI3ZGC/W10320581E comes with various attachments that expand its functionality. These attachments are tailored for specific tasks, such as mixing, whipping, and kneading, allowing users to tackle a wide array of recipes. The ease of switching attachments makes it simple to transition from one culinary task to another, making the cooking process streamlined and enjoyable.

The appliance is also designed with user-friendliness in mind. Intuitive controls and a clear design make it accessible for cooks of all skill levels. The LI3ZGC is not only powerful but also easy to clean, with many components being dishwasher-safe, which contributes to its overall convenience.

In summary, the KitchenAid LI3ZGC/W10320581E is a remarkable kitchen appliance that combines power, efficiency, and durability. With its advanced mixing technology, versatile attachments, and user-friendly design, it is an excellent addition to any kitchen, helping both novice and experienced cooks elevate their culinary creations.