KitchenAid Slide-out Vent Hood installation instructions To wire through top wiring

Page 6

wiring cutout

less than 5/8" (15.9 mm) including bottom filler if used.

8. To wire through top wiring

knockout, measure and mark a line 10-5/8" (27 cm) [for 30"

(76.2 cm) hood] or 11-5/8" (29.5 cm) [for 36" (91.4 cm) hood] from right of centerline on cabinet ceiling. Mark the point on this line that is 4" (10.2 cm) from back wall of cabinet. Drill a 1-1/4" (3.2 cm) diameter hole through the cabinet ceiling.

wiring cutout

To wire through rear wiring knockout, measure and mark a line 11-3/8" (29.8 cm) [for 30" (76.2 cm) hood] or 14-3/8"

(36.5 cm) [for 36" (91.4 cm) hood] from right of centerline on cabinet back wall. Mark the point on this line that is 8-1/4" (21 cm) from bottom of the cabinet. Drill a 1-1/4" (3.2 cm) diameter hole through the wall.

9. Run wiring through wall or cabinet according to the National Electrical Code and all local codes and ordinances. Do Not turn on power until installation is complete. Use caulking to seal around wire opening.

wood fillers – thickness as required

10. Measure the thickness of the cabinet floor, (including filler strips if used). If the thickness is less than 5/8"

(15.9 mm), install wood block fillers [5" (12.7 cm) long minimum] on cabinet floor. The mounting bracket adjusts from 5/8" (15.9 mm) to 2-1/8" (54 mm) for the wood block fillers.

damper

11. Remove vent hood from carton. Attach damper to vent opening. If roof cap has a damper, do not attach damper to vent hood.

wiring knockouts

12. Remove knockout from the wiring opening (top or rear) to be used.

terminal box cover

13. Place vent hood on its back side on a protected surface. Slide glass screen forward. Pull tabs to remove filters. Remove terminal box cover. Close glass screen. Slide mounting brackets to top position.

Note: For some installations using the non-vented (recirculating) kit, it may be easier to attach the vent system to the hood before lifting hood into its final position. Seal the connection with duct tape.

WARNING

Excessive Weight Hazard

Use two or more people to move and install vent hood.

Failure to do so can result in back or other injury.

mounting

bracket

cabinet

bottom

vent

hood

optional

wood block

14. Lift vent hood into final position and feed electrical wire through wiring opening. Mounting brackets should overlap cabinet bottom or wood blocks. Center range hood.

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Installation Instructions Use and Care Guide Before you start Metal snipsElectrical requirements Product dimensionsVent Hood Must be Connected with Copper Wire only 30 76.2 cm model 8 20.3 cm 36 91.4 cm model 11 27.9 cm4 x 10 8.3 cm x 25 cm Vent system Wall ventingRoof venting Maximum length = 26 ftNon-vented recirculating Kit, Part No must be used To wire through top wiring Mounting bracket Screw Adjustment screwsFor the Kwvu and Ykwvu model series FilterUse and Care Information For GZ or YGZ model seriesAccessories Vent System Warranty ONE-YEAR Full WarrantyRequesting Assistance or Service in U.S.A Requesting Assistance or Service in CanadaOur consultants provide assistance with Panneau avant personnalisé Étapes de l’installationPages Information dutilisationPince à dénuder Vis Volet de réglageNiveau PhillipsDimensions du produit Alimentation électriqueDécharge à travers le toit Conduit de 8,3 x 25 cm 4 x 10 poDécharge dans la pièce recyclage à travers le soffite 10 3/4 po Axe central Cales de bois27,3 cm Ouverture àBride de Opercules arrachables pour passage du câblageCouvercle de la boîte De connexion Fond du Montage Placard HottePanneau avant personnalisé Pour modèles des séries Kwvu et YkwvuPour modèles des séries GZ et YGZ 37,3 mm 15/32 po Tableau de Commande couvercle de plastiqueInformation d’utilisation et entretien Surface frontale du panneauAccessoires Garantie du système de ventilation Garantie Complète DE UN AN’exception de l’indicatif régional Demande d’assistance ou de service au CanadaSuccursales de service direct Et l’indicatif régional 807 en Ontario

Slide-out Vent Hood specifications

The KitchenAid Slide-out Vent Hood offers an innovative solution to maintaining a clean and comfortable kitchen environment. Designed to seamlessly blend into cabinetry, this vent hood provides functionality without compromising aesthetics. Its slide-out feature allows for easy access and efficient ventilation whenever cooking activities heat up, and it can be conveniently tucked away when not in use, preserving the sleek lines of your kitchen design.

One of the main features of the KitchenAid Slide-out Vent Hood is its powerful ventilation system, which effectively captures smoke, steam, and odors, ensuring that your kitchen remains fresh and free from airborne particles. With multiple fan speeds, users can easily adjust the airflow according to their cooking needs. The high-performance blower efficiently moves air, making it suitable for various cooking methods, from gentle simmering to high-heat frying.

In addition to its robust ventilation, this slide-out vent hood is equipped with bright, energy-efficient LED lighting. These lights illuminate the cooking surface below, enhancing visibility and ensuring that every culinary task is well-lit. The LEDs are not only long-lasting but also consume less energy, helping to reduce electricity bills while providing excellent illumination.

The KitchenAid Slide-out Vent Hood features a stainless steel construction, which is not only durable but also adds a modern touch to any kitchen decor. Its easy-to-clean design means that maintenance doesn’t become a chore; simply wipe down the surfaces to keep it looking new.

Another significant characteristic of this vent hood is its integrated grease filters, which are designed to capture and collect grease and other particles effectively. These filters are dishwasher-safe, making them convenient to clean and maintain, allowing for a more hygienic cooking environment.

Moreover, the KitchenAid Slide-out Vent Hood integrates seamlessly with other KitchenAid appliances, creating a cohesive look and feel within your kitchen. With options for customizable sizes and configurations, it can fit perfectly into a variety of kitchen layouts.

In summary, the KitchenAid Slide-out Vent Hood combines style, power, and convenience, making it an essential appliance for any home chef. Its advanced features, modern design, and user-friendly technologies elevate the kitchen experience, ensuring that cooking remains a pleasure rather than a chore.
Top Page Image Contents