KitchenAid W10579129B installation instructions Location Requirements

Page 4

Location Requirements

Grounded electrical supply required.

Do not run drain lines, water lines or electrical wiring where they can interfere with or contact dishwasher motor or legs.

The location where the dishwasher will be installed must provide clearance between motor and flooring. Motor should not touch the floor.

Do not install dishwasher over carpeted flooring.

Shelter dishwasher and water lines leading to dishwasher against freezing. Damage from freezing is not covered by the warranty.

A moisture barrier accessory (Part Number 4396277) is available from your dealer for installing underneath the countertop.

Call 1-800-422-1230to order. In Canada, call 1-800-807-6777.

Check location where dishwasher will be installed. The location must provide:

easy access to water, electricity and drain.

convenient access for loading and unloading dishes. Corner locations require a 2" (5.1 cm) minimum clearance between the side of the dishwasher door and the wall or cabinet.

square opening for proper operation and appearance.

cabinet front perpendicular to floor.

level floor. If floor at front of opening is not level with floor at rear of opening, shims may be needed to level dishwasher.

Helpful Tip: Be sure to accurately measure dimensions and ensure dishwasher is level if the floor in the dishwasher opening is uneven (example: Flooring extends only partway into opening).

NOTE: To avoid shifting during dishwasher operation, shims must be securely attached to the floor.

If dishwasher will be left unused for a period of time or in a location where it may be subject to freezing, have it winterized by authorized service personnel.

Make sure pipes, wires and drain hose are within the shaded area shown in the “Product and Cabinet Opening Dimensions” section.

4

Image 4
Contents Installation Instructions Undercounter Dishwasher Table of Contents All Installations Addition, for first-time installationsTools and Parts Supplied in KitLocation Requirements Product and Cabinet Opening Dimensions If connecting dishwasher with a power supply cord If connecting dishwasher with direct wiringDrain Requirements Water Supply RequirementsPrepare Cabinet Opening Existing Utilities Prepare Cabinet Opening-New UtilitiesOption B, Direct Wire Prepare and Route Water LineInstall Drain Hose Option B, No waste disposer no air gap Option A, Waste disposer no air gapOption C, Waste disposer with air gap Prepare Dishwasher Install Moisture BarrierOption D, No waste disposer with air gap Option A, Remove Access Panel Plastic Panel Make Power Supply Cord ConnectionOption B, Remove Access Panel Metal Panel Page Determine Cabinet Opening Custom Panel Dimensions Install Custom Panel Install Door HandleFollow steps below Page Choose Attachment Option Option A, Countertop attachmentPrepare Water Supply Line Option B, Dishwasher side attachmentMove Dishwasher Close to Cabinet Opening Page Connect to Water Supply Connect to DrainMake Direct Wire Electrical Connection Secure Dishwasher in Cabinet Opening Complete Installation Option A, Install Access Panel Plastic PanelOption B, Install Access Panel Metal Panel Reconnect Power Check OperationIf Dishwasher Does Not Operate Additional TipsTable DES Matières Il fautToutes les installations ’autre part, pour les premières installationsOutillage et pièces Fourniture dans la trousseExigences demplacement 24¹⁄₂ 23⁷⁄₈ 62,6 cm 62,2 cm 27¹⁄₂ 68,8 cm 30 76,2 cm 33¹⁄₂ Exigences d’évacuation Spécifications de l’alimentation en eauSpécifications électriques Pour le raccordement direct du lave-vaisselleInstructions Dinstallation Préparation et acheminement de l’alimentation électriqueOption A, cordon d’alimentation Option B, raccordement directPréparation et acheminement de la canalisation d’eau Installation du tuyau d’évacuation Option A, Broyeur à déchets sans brise-siphonOption B, Pas de broyeur à déchets sans brise-siphon Option C, Broyeur à déchets avec brise-siphonPréparation du lave-vaisselle Installation de la barrière anti-humiditéOption D, Pas de broyeur à déchets avec brise-siphon Option a Retrait du panneau daccès Panneau en plastique Option B Retrait du panneau daccès Panneau métalliqueRaccordement du cordon dalimentation Évaluation de l’ouverture dencastrement du placard Installation de la poignée de porte Dimensions du panneau personnaliséInstallation du panneau personnalisé Exécuter les étapes ci-dessousPage Option A, Fixation au plan de travail Choix de l’option de fixationOption B, Fixation au côté du lave-vaisselle Préparation de la canalisation dalimentation En eau Avertissement Remarques Raccordement à l’alimentation en eau Raccordement au circuit dévacuationRaccordement électrique direct Remarques Achever linstallation Option a Installation du panneau daccès Panneau en plastiqueOption B Installation du panneau daccès Panneau métallique Rétablir la source de courant électrique Si le lave-vaisselle ne fonctionne pas Contrôle du fonctionnementConseils supplémentaires Page W10579129B