Denon AVR-5800 Setting the Surround Back channel, Assignment of low frequency signal range

Page 21

NOTES:

— Assignment of low frequency signal range —

•The only signals produced from the subwoofer channel are LFE signals (during playback of Dolby Digital or DTS signals) and the low frequency signal range of channels set to “SMALL” in the setup menu. The low frequency signal range of channels set to “LARGE” are produced from those channels.

— Subwoofer mode —

•The subwoofer mode setting is only valid when “LARGE” is set for the front speakers and “YES” is set for the subwoofer in the “Speaker Configuration” settings (see page 19).

•When the “LFE+MAIN” playback mode is selected, the low frequency signal range of channels set to “LARGE” are produced simultaneously from those channels and the subwoofer channel.

In this playback mode, the low frequency range expand more uniformly through the room, but depending on the size and shape of the room, interference may result in a decrease of the actual volume of the low frequency range.

•Selection of the “LFE - THX” play mode will play the low frequency signal range of the channel selected with “LARGE” from that channel only. Therefore, the low frequency signal range that are played from the subwoofer channel are only the low frequency signal range of LFE (only during Dolby Digital or DTS signal playback) and the channel specified as “SMALL” in the setup menu. THX is recommended in this play mode so that bass interference is less likely to occur in the room.

•Select the play mode that provides bass reproduction with body.

Setting the Surround Back channel

Set the operation for the digital signals when playing in the 6.1 SURROUND, DTS-ES and THX SURROUND EX surround modes.

1

At the System Setup Menu select “SB CH Auto Flag Detect” and press

 

the ENTER button.

2

3

Select the desired setting.

We recommend setting this to “OFF”.

When set to “ON”, the operation for software for which no identification signals are recorded is set.

Enter the setting.

The System Setup Menu reappears.

THX surround EX/DTS ES Auto Flag Detect Mode (AFDM) setting

OFF

Set the “OFF” mode to perform 6.1-channel playback with conventional 5.1-channel sources or sources on which the

 

identification signal described below is not recorded.

ON

This function only works with software on which a special identification signal is recorded. This software is scheduled to go

 

on sale in the future.

 

This is a function for automatically playing in the 6.1-channel mode using the surround back speakers if the software is recorded

 

in THX Surround EX or DTS-ES or in the normal 5.1-channel mode without using the surround back speakers when the software

 

is not recorded in THX Surround EX or DTS-ES.

Non-Flag Source SB ch Output setting

OFF

Playback is conducted without using the surround back speaker.

Non MTRX

Playback is conducted using the surround back speaker. The same signals as those of the surround channels are output from

 

the surround back channel.

THX surround EX/DTS ES

..........Playback is conducted using the surround back speaker.

 

 

Surround back channel is reproduced using digital matrix processing.

NOTES:

•The “SB CH Auto Flag Detect” setting screen is displayed when the surround back speaker is set to “Large” or “Small” at “Speaker Configuration”.

•The surround back speakers can also be turned on and off using the “SB CH OUT” surround parameter. (See pages 51.) Select the setting according to the program source to be played.

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents AVR-5800 Safety Precautions Safety Instructions Before Using Table of ContentsFeatures Connections Connecting the audio componentsTV/DBS Connecting video componentsPrecaution when using S-jacks Connecting a video component equipped with S-Video jacksConnecting a DVD player DVD in jacks FM antenna adapter assembly Connecting the antenna terminalsConnecting the Multi Source jacks Connecting the external input EXT. in jacksConnecting the speaker cords Speaker system connectionsSpeaker Impedance Surround Speaker Systems a ConnectionsFront Panel Part Names and FunctionsRemote control unit Mute Setting UP the SystemSurround speaker selector function Speaker system layout6, 7 Before setting up the systemSetting the type of speakers Parameters Setting the Subwoofer modeAssignment of low frequency signal range Setting the Surround Back channelSubwoofer mode THX surround EX/DTS ES Auto Flag Detect Mode Afdm settingPreparations Setting the delay timeSetting the multi-zone 1 level Setting the Multi Zone Control40 dB, 0 dB VariableSetting the channel level Channel Level screen reappears Subwoofer peak limit level setting Setting the Digital In Assignment Auto tuner presets Setting the on-screen display OSDOn-screen display signals After completing system setupUsing the remote control unit Remote Control UnitOperating the remote control unit OperationBefore operating Input mode selection function Playing the input sourceExample CD Adjusting the sound quality tone After starting playbackExample Stereo Switching the surround speakers Listening over headphonesChecking the currently playing program source, etc Turning the sound off temporarily mutingPlaying one source while recording another REC OUT mode Multi-source recording/playbackRecording Dolby Digital and DTS multichannel sources Press the M-ZONE 1 button PRE OUT EFFECT/SB left and right jacks Playback using the external input EXT. in jacksDirect mode Pure Direct modeStereo mode Playing audio sources CDs and DVDsMulti-source and multi-zone playback Multi-zone playback using the Multi Zone 1 terminalsRemote Control Unit Multi-zone playback using the Multi Zone 2 terminalsBefore playing with the surround function SurroundFader function Remote Control UnitPlaying modes for different sources Surround parameters q Afdm Auto Flag Detect Mode THX Surround EX / Home THX Cinema modeSelect the Surround mode Set the input mode to AutoDTS Neo6 mode Dolby Surround Pro Logic modeSurround modes and their features Denon Original Surround ModesPersonal Memory Plus DSP surround simulation Select the surround mode for the input channelTone control setting Surround modes and parameters Surround parameters eAuto tuning Manual tuningListening to the Radio Checking the preset stations Preset memoryRemote control unit Main unitRecalling preset stations Last Function MemoryInitialization of the Microprocessor Troubleshooting Additional Information Types of multi-channel signalsOptimum surround sound for different sources Movie audioNumber of surround back speakers Surround back speakersSpeaker setting examples When not using surround back speakers When using different surround speakers for movies and musicDolby Surround Dolby Digital Dolby Surround AC-3 Surround2Dolby Digital and Dolby Pro Logic Dolby Digital compatible media and playback methodsDolby Pro Logic DTS Digital SurroundDolby Pro Logic compatible media and playback methods DTS compatible media and playback methodsDTS-ES Extended Surround TM THX Surround EX Home THX Cinema surround modeTHX Surround modes and parameters Audio section Specifications14-14, Akasaka 4-CHOME, MINATO-KU, Tokyo 107-8011, Japan
Top Page Image Contents