Hotpoint CH 10756 GF S Setting the time of day, Timer function buttons, Auto cooking programme

7.On warm days, to prevent harmful bacterial growth in certain foods (ie poultry, joints, etc) the delayed start should be kept to a minimum.

8.Wine or beer may ferment and cream may curdle during the delay period, so it is best to add these ingredients just before serving.

9.Foods which discolour should be protected by coating in fat or tossing in water to which lemon juice has been added, prior to placing food in the oven.

10.Dishes containing liquid should not be filled too full to prevent boiling over.

11.Food should be well sealed (but not airtight) in a container to prevent the loss of liquid during cooking. Aluminium foil gives a good seal.

12.Ensure food is cooked thoroughly before serving.

End Time Button

The time of day at which you want an “Auto Cooking” GB programme to end.

For Example: If you set a “Cook Period” for 2 hours, and “End Time” of 11:00. The timer will switch the oven(s) on at 9:00 and turn the oven(s) off at 11:00. You will hear a audible tone at 11:00, to indicate that the Auto Cooking Programme has finished.

Notes:

-When setting an Auto Cooking programme you will need to set the oven control(s) to the required temperature(s) when you set the timer.

-If an Auto Cooking programme has been set the oven(s) will only operate during the pre-programmed time.

CLOCKFACE

U

A 0 . 0 0

T

O

SYMBOLS

The timer incorporates a 24 hour clock.

Ensure the correct time of day is always set, before using your cooker.

Manual Button

Needs to be pressed to cancel an Auto Cooking programme and return the oven(s) to Manual operation.

“+” and “-” Buttons

Used to adjust the various timer function settings.

	0 .	0 0	A ‘bell’ symbol will light up when you
			select a Minute Minder Period and
			will remain lit for the period set.
			At the end of the Minute Minder
			Period, the timer will emit an audible
tone and the ‘bell’ symbol will disappear.
			The ‘cookpot’ symbol will light up
	0 . 0 0
			either:-
			- When the timer is in manual mode, or
			- During the actual Cook Period.
			‘AUTO’ will light up:-
	0 . 0 0
A
			- When the timer is first turned on
U
T
O			it will flash. It will go out when a time

of day is set or when the timer is set to manual.

The ‘AUTO’ symbol will flash at the end of an Auto Cooking programme to indicate that the programme has finished.

(When the ‘AUTO’ symbol is flashing, to return the oven to Manual operation, turn the oven controls off, ensure that the correct time of day is set, and press the “Manual” button - The ‘AUTO’ symbol will go out).

Setting the time of day

A	0 . 0 0	Step 1 Make sure all oven controls
		are turned Off.
T
U
O		Step 2 Check the electricity supply
		to the cooker is turned on.
		Step 3 When switched on the
		display will show 0.00 and the Auto
	0 . 0 0	symbol, flashing intermittently.
A		Step 4 Press & hold in both the Cook
O
U		Period & End Time buttons together.
T
		Step 5 With the Cook Period &
		End Time buttons still held in,
		press either the “+” or “-” buttons to
set the correct time of day.

Step 6 Release all the buttons simultaneously. THE TIME OF DAY IS NOW SET.

To change the time of day repeat Steps 4, 5 & 6 above.

Note: You cannot adjust the time of day if the timer has been set for an Auto Cooking Programme.

Timer function buttons

Minute Minder Button

Here you can set a time period of up to 23 hours 59 minutes, that will count down. When it reaches zero, the timer will emit an audible tone.

For Example: If you set 20 minutes, the audible tone will occur 20 minutes later.

Auto cooking programme

Cook Period Button

Cook Period is the actual length of time for which, the timer will switch the oven(s) on as part of an “Auto Cooking” programme. (e.g. If you set 2 hours, the food will be cooked for 2 hours).

Setting the minute minder

Step 1 Ensure the time of day is set correctly.

0 . 0 0	Step 2 Press and hold the Minute
	Minder button.
	Step 3 With the Minute Minder button
	held in, set the required Minute
	Minder period using the “+” and “-”
	buttons. A ‘bell’ symbol will light up.

Release all buttons and the timer display will revert back to the time of day. The ‘bell’ symbol will remain lit to signify that a Minute Minder period has been set.

At the end of the set time an audible tone will be heard, and the ‘bell’ symbol will disappear.

PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24

9