Denon DN-A7100 manual Speakers Distance, SURR. Back Size, Lpf/Hpf, Bass MIX

Page 25

SURR. BACK SIZE

LARGE:

Select if the surround back speaker is large.

SMALL:

Select if the surround back speaker is small.

Note:

If “NONE” is selected for the Surround L/R setting, then this setting is not available.

LPF/HPF

When you use a subwoofer, you can select the cutoff frequency for the small speakers used. Select one of the crossover frequency levels according to the size of the small speaker connected.

80Hz → 100Hz → 120Hz → 150Hz → 180Hz

Notes:

•If using small front speakers, set a slightly higher frequency. If using large front speakers, set a slightly lower frequency.

•If Pure-Direct mode, 7.1CH Input is in use, this function does not take effect.

BASS MIX

•The bass mix setting is only valid when “LARGE” is set for the front speakers and “YES” is set for the subwoofer during stereo playback .

This setting has effect only during playback of PCM or analog stereo sources.

•When “BOTH” is selected, the low frequencies will be played through the main L&R, as well as the sub woofer.

In this playback mode, the low frequency range expand more uniformly through the room, but depending on the size and shape of the room, interference may result in a decrease of the actual volume of the low frequency range.

•By selecting “MIX”, the low frequencies will play through the main L&R ONLY.

Note:

LFE signals during playback of Dolby Digital or DTS, will be played through the sub woofer.

2-2 SPEAKERS DISTANCE

Use this parameter to specify the distance of each speaker’s position from the listening position. The delay time is automatically calculated according to these distances.

Begin by determining the ideal or most commonly used seating position in the room.

This is important for the timing of the acoustics to create the proper sound space that the DN-A7100 and today’s sound systems are able to produce.

Note:

For speakers that you have selected “NONE” the Speaker Configuration sub-menu will not appear here. (There are several useful books and special DVD and LD’s available to guide you through proper home theater configuration. If you are unsure, have your DENON dealer perform the installation for you. They are trained professionals familiar with even the most sophisticated custom installations. DENON recommends the WWW.CEDIA.ORG website for further information about this).

2-2 SPEAKERS DISTANCE

FRONT L

: 10 ft

3.0

m

FRONT R

: 10 ft

3.0

m

CENTER

: 10 ft

3.0

m

SURR.L

: 10 ft

3.0

m

SURR.R

: 10 ft

3.0

m

SUB W

: 10

ft

3.0

m

SURR.B L : 10

ft

3.0

m

SURR.B R : 10

ft

3.0

m

MAIN RETURN

 

EXIT

1. To select each speaker , press the 3 or 4 cursor buttons.

2. To set the distance for each speaker , press the 1 or 2 cursor buttons.

3. After you complete this portion of the set up, move the cursor to “NEXT” with the 3 or 4 cursor buttons and then press the ENTER button to go to the next page.

FRONT L:

Set the distance from the front left speaker to your normal listening position.

CENTER:

Set the distance from the center speaker to your normal listening position.

FRONT R:

Set the distance from the front right speaker to your normal listening position.

SURR. L:

Set the distance from the surround left speaker to your normal listening position.

SURR. R:

Set the distance from the surround right speaker to your normal listening position.

SUB W:

Set the distance from the subwoofer to your normal listening position.

SURR. B L:

Set the distance from the surround back left speaker to your normal listening position.

SURR. B R:

Set the distance from the surround back right speaker to your normal listening position.

Notes:

•Set the distance to each speaker in meters (m) or feet (ft) as follows.

m:0.3 - 9 m in 0.3 m steps

ft: 1 - 30 ft in 1 ft steps

•For the speakers that you have selected “NONE” the Speaker Size menu will not appear.

•The setting for Surr.Back L and Surr.Back R appears if you set for it to, two surround back speakers in the Speaker Size menu.

•The setting of Surr.Back appears if it is set for one surround back speaker in the Speaker Size menu.

2-3. SPEAKERS LEVEL SETTING WITH TEST TONE

Here you will set the volume for each speaker so that they are all heard by the listener at the same level. We recommend using a SPL (Sound Pressure Level) meter, when available.

Note:

The speaker level settings are not available in 7.1 Channel Input mode, CS mode and Multi Channel Stereo mode.

2-3 SPEAKERS

LEVEL

 

TEST MODE

:

MANUAL

FRONT L

:

0

dB

CENTER

:

0

dB

FRONT R

:

0

dB

SURR.R

:

0

dB

SURR.B R

:

0

dB

SURR.B L

:

0

dB

SURR.L

:

0

dB

SUB W

:

0

dB

MAIN RETURN

 

 

EXIT

 

 

 

 

TEST MODE :

Selects “MANUAL” or “AUTO” for generating the mode of the test tone with the 1 or 2 cursor buttons.

If you select “AUTO” , the test tone will be cycled through in a circular pattern which is Left → Center → Right → Surround Right → Surround Back Right → Surround Back Left → Surround Left → Subwoofer

→Left → .. increments of 2 seconds for each channel.

Using the 1 or 2 cursor buttons, adjust the volume level of the noise from the speaker so that it is the same level for all the speakers.

If you select “MANUAL”, adjust the output level of each speaker as listed below.

1. When you move the cursor to FRONT L by pressing the 4 cursor button, the DN-A7100 will emit a pink noise from the front left speaker.

Remember the level of this noise and then press the 4 cursor button.

(Note that this can be adjusted to any level between -10 and +10 dB in 1 dB intervals except the subwoofer setting. The subwoofer can be adjusted to any level between -15 and +10 dB in 1 dB intervals.)

The DN-A7100 will now emit the pink noise from the center speaker.

2. Using the 1 and 2 cursor buttons, adjust the volume level of the noise from the center speaker so that it is the same level as the front left speaker.

3. Press the 4 cursor button again. The DN- A7100 will now emit the pink noise from the front right speaker.

4. Repeat steps 2 and 3 above for the front right and other speakers until all speakers are adjusted to the same volume level.

After you complete this portion of the set up, press the ENTER button, the cursor will move to “MAIN” and then press the ENTER button to go to SETUP MAIN MENU.

Notes:

•Speakers that you selected “NONE” for in the Speaker Size menu will not appear.

•The setting of Surr.Back L and Surr.Back R appears if you have set it for two surround back speakers in the Speaker Size menu.

•The setting of Surr.Back appears if you have set it for one surround back speaker in the Speaker Size menu.

•To adjust the speaker levels for 7.1-channel input sources, you will need to use the 7.1CH-INPUT sub menu. (See page 23).

ENGLISH

21

Page 24 Page 26
Image 25
Page 24 Page 26
Contents DN-A7100 Deutsch EnglishFrançais ItalianoDeutsch EnglishWarnhinweise FrançaisAdvertencias AvvertenzeWaarschuwingen AdvertênciasRecycling Table of Contents Foreword IntroductionNeo6 offers several important improvements as follow DescriptionAbout Dolby Pro Logic Accessories FeaturesFront Panel FL Display TV, DVD, VCR, DSS/VCR2 Rear Panel5AUX1 analog audio input jacks L/R 4AUX1 analog audio input level switch -10dBV/+4dBu6AUX1 Video / Digital Audio Input 7RS-232CFunction and Operation Remote Control Operation¤5 Volume +/- buttons ¤3 Tuning +/- buttons¤1 MEMO/HT-EQ button ¤2 A/D buttonRemote control unit RC-1065 Operation of Remote Control UnitLoading Batteries May not be possibleGeneral Information of RC-1065 to DN-A7100 AMP ModeConnections Speaker PlacementHeight of the Speaker Units Connecting a Subwoofer Connecting SpeakersXLR terminals are used for balanced inputs OutputsConnecting Digital Audio Components Connecting Audio ComponentsVIDEO, S-VIDEO , Component Jacks Connecting Video ComponentsVideo jack Component jackConnecting Multi Channel Audio Source Advanced ConnectingConnecting AN External Power Amplifier Connecting the Supplied Antennas Connecting the Antenna TerminalsConnecting AN FM Outdoor Antenna Connecting AN AM Outdoor AntennaHdmi Jack Connecting Hdmi DevicesSelect an input source from the OSD menu system. See On Screen Display Menu System SetupSpeakers Size Speaker SetupSURR. Back Size Speakers DistanceLPF/HPF Bass MIXSurround PreferenceCS II Circle Surround II Parameter CH Input LevelRelation of the speakers number and conectted speaker Simple SetupRelation of the room size and floor space Selecting AN Input Source Basic OperationVideo Convert Example DVDAdjusting the Tone Bass & Treble Using the Sleep Timer Selecting the Surround ModeAdjusting the Main Volume ControlSurround Mode Virtual CSII-Mono modeStereo Source DirectFront speakers AbbreviationsCenter speaker SL/SR Surround speakersOther Function Listening Through HeadphonesTV Auto ON/OFF Function Video ON/OFFHT-EQ Home Theater Equalizer Recording AN Analog SourceCH Input This permits simultaneous viewing with video sourcesLIP.SYNC AUX2 InputListening to the Tuner FM Tuning Mode Auto Stereo or Mono Preset MemoryAuto Preset Memory Manual Preset MemoryName Input of the Preset Station Sorting Preset StationsYou can remove preset stations from the memory → B → C ... Z → 1 → 2 → 3 .... → → + → / → Blank → a UP →Radio Text RDS OperationRDS Display Programme Type PTY DisplaySymptom Cause Remedy TroubleshootingGlobal Description RS-232C Control SpecificationDetailed Description Transaction Sequences and the Regulations Examples of the handshaking flowchart Recommendations of COMMAND, Status and Layer DefinitionExamples of handshaking error Example of successful handshakingNormal Command list Recommendations of COMMAND, Status and LayerSpecific Commands Normal Status request and Status answer and feedback list Status Request and Status Answer ListDimensions Technical SpecificationsHoldings Inc

DN-A7100 specifications

The Denon DN-A7100 is a versatile, high-performance audio amplifier designed for various professional and home audio applications. Known for its robust build quality and impressive technical specifications, it serves as an ideal solution for those seeking to enhance their sound experience.

One of the standout features of the DN-A7100 is its power output. Delivering up to 150 watts per channel into 8 ohms and 200 watts into 4 ohms, it ensures dynamic and clear audio performance, capable of driving a wide range of speakers. The amplifier utilizes a Class D design, which not only provides high efficiency but also minimizes heat generation. This characteristic makes it suitable for extended usage without risking thermal overload.

The DN-A7100 integrates advanced digital signal processing (DSP) technology that allows for a rich array of sound tailoring options. Users can take advantage of various EQ settings and audio presets to customize the sound to their preferences or the acoustics of their environment. This flexibility is particularly valuable in live sound situations or in home theater setups where room dynamics significantly affect audio quality.

Connectivity is another strong point of the DN-A7100. It features multiple inputs, including balanced XLR, RCA, and digital inputs, facilitating easy integration with different sound sources. Additionally, the amplifier supports both stereo and bridged mode operation, allowing for versatile application in various configurations.

Furthermore, the DN-A7100 incorporates built-in protection circuits that safeguard against overloading, overheating, and short circuits. These safety features ensure that the amplifier operates reliably over time, preserving both its functionality and the integrity of connected audio equipment.

An intuitive front panel further enhances user experience, featuring a clear LCD display that provides easy access to settings and functions. The unit also supports remote control operation, allowing for flexible adjustments without needing to be physically present at the unit.

In summary, the Denon DN-A7100 is a powerful audio amplifier that excels in performance and adaptability. With its robust power output, advanced DSP capabilities, numerous connectivity options, and user-friendly features, it is an excellent choice for both audio professionals and home enthusiasts looking to elevate their audio experience. Whether in a professional sound environment or a home theater setup, the DN-A7100 delivers exceptional sound quality and reliable performance.
Top Page Image Contents