Denon 483, AVR-1403 manual Connecting the antenna terminals, AM loop antenna assembly

Page 12

ENGLISH

Connecting the antenna terminals

 

AM LOOP

 

ANTENNA

 

(An Accessory)

DIRECTION OF

 

BROADCASTING

 

STATION

 

FM ANTENNA

 

75 /ohms

 

COAXIAL

 

CABLE

 

 

AM OUTDOOR

 

ANTENNA

FM INDOOR ANTENNA

GROUND

(An Accessory)

 

AM loop antenna assembly

 

 

Connect to the AM

1

2

antenna terminals.

3

 

 

 

Remove the vinyl tie

 

 

and take out the

Bend in the reverse

4

connection line.

direction.

 

 

a. With the antenna on top any stable surface.

Mount

b. With the antenna attached to a wall.

Installation hole

Mount on wall, etc.

Connection of AM antennas

1. Push the lever.

2. Insert the

3. Return the lever.

 

conductor.

 

Note to CATV system installer:

This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC which provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.

Notes:

Do not connect two FM antennas simultaneously.

Even if an external AM antenna is used, do not disconnect the AM loop antenna.

Make sure AM loop antenna lead terminals do not touch metal parts of the panel.

12

Image 12
Contents AVR-1403/483 Nous vous remercions pour l’achat de cet appareilEnglish Francais Safety Instructions Table of Contents Before UsingFeatures Part Names and Functions Front PanelRemote control unit System System SET UPSetting UP the Speaker Systems Finally, setting up the systemRead this First Connecting the audio components ConnectionsUse the AC Outlet for audio equipment only. Do not use It for hair driers, etcConnecting the video equipments Audio OUT Video OUTConnecting a Video game equipment Connecting the antenna terminals AM loop antenna assemblyConnecting the speaker cords Speaker system connectionsSpeaker Impedance Protector circuit Using the Remote Control Unit Range of operation of the remote control unitInserting the batteries Setting UP the System Use the following buttons to set up the systemSystem SET UP Front LargeCenter Small SURR. SmallSW Mode Norm Setting the Subwoofer ModeWoofer YES Setting the speaker distance PreparationsListening position Digital input setup After setting up the systemCoax DVD Terminal InitialRemote Control Unit Preset memory Audio componentOperating Denon audio components Preset memory Video component Operating a video component stored in the preset memory For DVD playerFor video disc player VDP For video deck VCRCheck that all connections are proper Turn on the power Button on the remote control unit to turn on the powerOperation Before operatingTo select the input mode from main unit To select the input mode from the remote control unitInput mode selection function Playing the input sourceAdjusting the sound quality tone After starting playbackDolby Digital DTSListening over headphones Turning the sound off temporarily mutingChecking the currently playing program source, etc Playback using the external input EXT. in jacks Mode AUTO, PCM, DTS or Analog button to switch toFollow to 3 under Playing the input source Adjust the level of the selected speaker SurroundBefore playing with the surround function Dolby Surround Pro Logic II mode Dolby PRO LogicDimension setting Center Width settingDefault setting Surround parameters q Pro Logic II ModeCinema EQ OFF Dolby PLII, Dolby PROLOGIC, Dolby DIGITAL, DTSDefault COMP. OFFSurround parameters w Cinema EQ. Cinema Equalizer COMP. Dynamic Range CompressionSurround modes and their features DSP Surround SimulationVideo Game Personal Memory PlusRoom Size MED Effect LevelDSP surround simulation Use Left Right buttons to set the room size InitialDefault Y/N Use Left Right buttons to set the delay time InitialWhen press the UP button When press the Down buttonPress the Surround Parameter button Surround parameters e Surround modes and parametersAuto preset memory Listening to the RadioAuto tuning Manual tuningSet the input function to Tuner Preset stations Recalling preset stationsLast Function Memory Initialization of the MicroprocessorSpeaker setting examples Additional InformationSurround Dolby Digital and Dolby Pro Logic Dolby Digital compatible media and playback methodsDolby Pro Logic DTS Digital Surround DTS compatible media and playback methodsTroubleshooting Specifications Audio sectionMono StereoList of Preset Codes / Liste DE Codes Préréglés DVD VDPVCR Francais English 16-11, Yushima 3-CHOME, BUNKYOU-KU, Tokyo 113-0034, Japan Page Page Page