Denon 483, AVR-1403 manual DSP Surround Simulation, Surround modes and their features, Video Game

Page 34

ENGLISH

14

DSP SURROUND SIMULATION

•This unit is equipped with a high performance DSP (Digital Signal Processor) which uses digital signal processing to synthetically recreate the sound field. One of 7 preset surround modes can be selected according to the program source and the parameters can be adjusted according to the conditions in the listening room to achieve a more realistic, powerful sound. These surround modes can also be used for program sources not recorded in Dolby Surround Pro Logic or Dolby Digital.

Surround modes and their features

 

 

In this mode, the signals of the front left channel are output from the left surround channel, the signals of the front

1

5CH STEREO

right channel are output from the right surround channel, and the same (in-phase) component of the left and right

channels is output from the center channel. This mode provides all speaker surround sound, but without directional

 

 

 

 

steering effects, and works with any stereo program source.

 

 

 

2

MONO MOVIE

Select this when watching monaural movies for a greater sense of expansion.

(NOTE 1)

 

 

 

 

 

3

ROCK ARENA

Use this mode to achieve the feeling of a live concert in an arena with reflected sounds coming from all directions.

 

 

 

4

JAZZ CLUB

This mode creates the sound field of a live house with a low ceiling and hard walls. This mode gives jazz a very

vivid realism.

 

 

 

 

 

5

VIDEO GAME

Use this to enjoy video game sources.

 

 

 

 

 

Select this to emphasize the sense of expansion for music sources recorded in stereo. Signals consisting of the

6

MATRIX

difference component of the input signals (the component that provides the sense of expansion) processed for

 

 

delay are output from the surround channel.

 

 

 

7

VIRTUAL

Select this mode to enjoy a virtual sound field, produced from the front 2-channel speakers.

 

 

 

Depending on the program source being played, the effect may not be very noticeable.

In this case, try other surround modes, without worrying about their names, to create a sound field suited to your tastes.

NOTE 1: When playing sources recorded in monaural, the sound will be one-sided if signals are only input to one channel (left or right), so input signals to both channels. If you have a source component with only one audio output (monophonic camcorder, etc.) obtain a “Y” adaptor cable to split the mono output to two outputs, and connect to the L and R inputs.

NOTE:

Only the STEREO mode can be used when playing PCM signals with a sampling frequency of 96 kHz (such as from DVD-Video discs that contain 24 bit, 96 kHz audio). If such signals are input during playback in one of the other surround modes, the mode automatically switches to STEREO.

If the DTS signals are input during playback in VIRTUAL surround mode, the mode automatically switches to STEREO.

Personal Memory Plus

This set is equipped with a personal memorize function that automatically memorizes the surround modes and input modes selected for the input different sources. When the input source is switched, the modes set for that source last time it was used are automatically recalled.

The surround parameters, tone control settings and playback level balance for the different output channels are memorized for each surround mode.

34

Page 33 Page 35
Image 34
Page 33 Page 35
Contents AVR-1403/483 Nous vous remercions pour l’achat de cet appareilEnglish Francais Safety Instructions Table of Contents Before UsingFeatures Part Names and Functions Front PanelRemote control unit System System SET UPFinally, setting up the system Setting UP the Speaker SystemsRead this First Use the AC Outlet for audio equipment only. Do not use Connecting the audio componentsConnections It for hair driers, etcConnecting the video equipments Audio OUT Video OUTConnecting a Video game equipment Connecting the antenna terminals AM loop antenna assemblySpeaker system connections Connecting the speaker cordsSpeaker Impedance Protector circuit Range of operation of the remote control unit Using the Remote Control UnitInserting the batteries Setting UP the System Use the following buttons to set up the systemCenter Small System SET UPFront Large SURR. SmallSetting the Subwoofer Mode SW Mode NormWoofer YES Preparations Setting the speaker distanceListening position Coax DVD Digital input setupAfter setting up the system Terminal InitialPreset memory Audio component Remote Control UnitOperating Denon audio components Preset memory Video component For video disc player VDP Operating a video component stored in the preset memoryFor DVD player For video deck VCROperation Check that all connections are proper Turn on the powerButton on the remote control unit to turn on the power Before operatingInput mode selection function To select the input mode from main unitTo select the input mode from the remote control unit Playing the input sourceDolby Digital Adjusting the sound quality toneAfter starting playback DTSTurning the sound off temporarily muting Listening over headphonesChecking the currently playing program source, etc Mode AUTO, PCM, DTS or Analog button to switch to Playback using the external input EXT. in jacksFollow to 3 under Playing the input source Surround Adjust the level of the selected speakerBefore playing with the surround function Dolby Surround Pro Logic II mode Dolby PRO LogicDefault setting Dimension settingCenter Width setting Surround parameters q Pro Logic II ModeCinema EQ OFF Dolby PLII, Dolby PROLOGIC, Dolby DIGITAL, DTSSurround parameters w Cinema EQ. Cinema Equalizer DefaultCOMP. OFF COMP. Dynamic Range CompressionVideo Game Surround modes and their featuresDSP Surround Simulation Personal Memory PlusDSP surround simulation Room Size MEDEffect Level Use Left Right buttons to set the room size InitialDefault Y/N Use Left Right buttons to set the delay time InitialWhen press the Down button When press the UP buttonPress the Surround Parameter button Surround parameters e Surround modes and parametersAuto preset memory Listening to the RadioManual tuning Auto tuningSet the input function to Tuner Preset stations Recalling preset stationsLast Function Memory Initialization of the MicroprocessorAdditional Information Speaker setting examplesSurround Dolby Digital compatible media and playback methods Dolby Digital and Dolby Pro LogicDolby Pro Logic DTS Digital Surround DTS compatible media and playback methodsTroubleshooting Mono SpecificationsAudio section StereoVDP List of Preset Codes / Liste DE Codes Préréglés DVDVCR Francais English 16-11, Yushima 3-CHOME, BUNKYOU-KU, Tokyo 113-0034, Japan Page Page Page
Top Page Image Contents