Denon AVR-1403, 483 Using the Remote Control Unit, Range of operation of the remote control unit

Page 15

ENGLISH

9 USING THE REMOTE CONTROL UNIT

Following the procedure outlined below, insert the batteries before using the remote control unit.

Range of operation of the remote control unit

30° 30°

Approx. 23 feet/7 m

Point the remote control unit at the remote control sensor as shown on the diagram at the left.

NOTES:

•The remote control unit can be used from a straight distance of approximately 23 feet/7 meters, but this distance will shorten or operation will become difficult if there are obstacles between the remote control unit and the remote control sensor, if the remote control sensor is exposed to direct sunlight or other strong light, or if operated from an angle.

•Neon signs or other devices emitting pulse-type noise nearby may result in malfunction, so keep the set as far away from such devices as possible.

Inserting the batteries

qPress as shown by the arrow and slide off.

w Insert the R6P/AA batteries properly, as	e Close the lid.
shown on the diagram.

NOTES:

•Use only R6P/AA batteries for replacement.

•Be sure the polarities are correct. (See the illustration inside the battery compartment.)

•Remove the batteries if the remote control transmitter will not be used for an extended period of time.

•If batteries leak, dispose of them immediately. Avoid touching the leaked material or letting it come in contact with clothing, etc. Clean the battery compartment thoroughly before installing new batteries.

•Have replacement batteries on hand so that the old batteries can be replaced as quickly as possible when the time comes.

•Even if less than a year has passed, replace the batteries with new ones if the set does not operate even when the remote control unit is operated nearby the set. (The included battery is only for verifying operation. Replace it with a new battery as soon as possible.)

15

Image 15

Contents Nous vous remercions pour l’achat de cet appareil AVR-1403/483English Francais Safety Instructions Before Using Table of ContentsFeatures Front Panel Part Names and FunctionsSystem System SET UP Remote control unitSetting UP the Speaker Systems Finally, setting up the systemRead this First It for hair driers, etc Connecting the audio componentsConnections Use the AC Outlet for audio equipment only. Do not useAudio OUT Video OUT Connecting the video equipmentsConnecting a Video game equipment AM loop antenna assembly Connecting the antenna terminalsConnecting the speaker cords Speaker system connectionsSpeaker Impedance Protector circuit Using the Remote Control Unit Range of operation of the remote control unitInserting the batteries Use the following buttons to set up the system Setting UP the SystemSURR. Small System SET UPFront Large Center SmallSW Mode Norm Setting the Subwoofer ModeWoofer YES Setting the speaker distance PreparationsListening position Terminal Initial Digital input setupAfter setting up the system Coax DVDRemote Control Unit Preset memory Audio componentOperating Denon audio components Preset memory Video component For video deck VCR Operating a video component stored in the preset memoryFor DVD player For video disc player VDPBefore operating Check that all connections are proper Turn on the powerButton on the remote control unit to turn on the power OperationPlaying the input source To select the input mode from main unitTo select the input mode from the remote control unit Input mode selection functionDTS Adjusting the sound quality toneAfter starting playback Dolby DigitalListening over headphones Turning the sound off temporarily mutingChecking the currently playing program source, etc Playback using the external input EXT. in jacks Mode AUTO, PCM, DTS or Analog button to switch toFollow to 3 under Playing the input source Adjust the level of the selected speaker SurroundBefore playing with the surround function Dolby PRO Logic Dolby Surround Pro Logic II modeSurround parameters q Pro Logic II Mode Dimension settingCenter Width setting Default settingDolby PLII, Dolby PROLOGIC, Dolby DIGITAL, DTS Cinema EQ OFFCOMP. Dynamic Range Compression DefaultCOMP. OFF Surround parameters w Cinema EQ. Cinema EqualizerPersonal Memory Plus Surround modes and their featuresDSP Surround Simulation Video GameUse Left Right buttons to set the room size Initial Room Size MEDEffect Level DSP surround simulationUse Left Right buttons to set the delay time Initial Default Y/NWhen press the UP button When press the Down buttonPress the Surround Parameter button Surround modes and parameters Surround parameters eListening to the Radio Auto preset memoryAuto tuning Manual tuningSet the input function to Tuner Recalling preset stations Preset stationsInitialization of the Microprocessor Last Function MemorySpeaker setting examples Additional InformationSurround Dolby Digital and Dolby Pro Logic Dolby Digital compatible media and playback methodsDolby Pro Logic DTS compatible media and playback methods DTS Digital SurroundTroubleshooting Stereo SpecificationsAudio section MonoList of Preset Codes / Liste DE Codes Préréglés DVD VDPVCR Francais English 16-11, Yushima 3-CHOME, BUNKYOU-KU, Tokyo 113-0034, Japan Page Page Page