Denon 483, AVR-1403 manual Playback using the external input EXT. in jacks

Page 28

ENGLISH

Playback using the external input (EXT. IN) jacks

1

Set the external input (EXT.

8

 

 

 

IN) mode.

 

 

Press the EXT. IN to switch

 

 

the external input.

 

B

(Main unit)

(Remote control unit)

Once this is selected, the input signals connected to the FL (front left), FR (front right), C (center), SL (surround left), and SR (surround right) channels of the EXT. IN jacks are output directly to the front (left and right), center, surround (left and right) speaker systems without passing through the surround circuitry.

In addition, the signal input to the SW (subwoofer) jack is output to the PRE OUT SUBWOOFER jack.

2

Cancelling the external input mode

 

 

 

 

To cancel the external input (EXT. IN) setting, press the INPUT

 

MODE (AUTO, PCM, DTS) or ANALOG button to switch to

 

the desired input mode. (See page 25.)

 

 

 

8

 

(Main unit)

(Remote control unit)

When the input mode is set to the external input (EXT. IN), the play mode (STEREO, DOLBY/DTS SURROUND, 5CH STEREO or DSP SIMULATION) cannot be set.

2

1

 

 

 

 

V. AUX

VCR

 

TV/DBS

 

4

5

6

7

1, 2

INPUT MODE

CDR / TAPE

TUNER

SHIFT

8

9

0

 

 

SURROUND

TAPE·VCR

 

 

MODE

 

 

 

6

7

 

CHANNEL

NOTES:

In play modes other than the external input mode, the signals connected to these jacks cannot be played. In addition, signals cannot be output from channels not connected to the input jacks.

The external input mode can be set for any input source. To watch video while listening to sound, select the input source to which the video signal is connected, then set this mode.

Recording the program source (recording the source currently being monitored)

1

Follow step 1 to 3 under “Playing the input source”.

2

Start recording on the tape or video deck.

 

 

For instructions, refer to the component’s operating instructions.

Simultaneous recording

The signals of the source selected with the function selector button are output simultaneously to the CDR/TAPE and VCR REC OUT jacks. If a total of two tape and/or video decks are connected and set to the recording mode, the same source can be recorded simultaneously on every decks.

NOTE:

The AUDIO IN’s signal selected with the function selector button are output to the CDR/TAPE and VCR AUDIO OUT jacks.

28

Image 28
Contents AVR-1403/483 Nous vous remercions pour l’achat de cet appareilEnglish Francais Safety Instructions Table of Contents Before UsingFeatures Part Names and Functions Front PanelRemote control unit System System SET UPFinally, setting up the system Setting UP the Speaker SystemsRead this First Connecting the audio components ConnectionsUse the AC Outlet for audio equipment only. Do not use It for hair driers, etcConnecting the video equipments Audio OUT Video OUTConnecting a Video game equipment Connecting the antenna terminals AM loop antenna assemblySpeaker system connections Connecting the speaker cordsSpeaker Impedance Protector circuit Range of operation of the remote control unit Using the Remote Control UnitInserting the batteries Setting UP the System Use the following buttons to set up the systemSystem SET UP Front LargeCenter Small SURR. SmallSetting the Subwoofer Mode SW Mode NormWoofer YES Preparations Setting the speaker distanceListening position Digital input setup After setting up the systemCoax DVD Terminal InitialPreset memory Audio component Remote Control UnitOperating Denon audio components Preset memory Video component Operating a video component stored in the preset memory For DVD playerFor video disc player VDP For video deck VCRCheck that all connections are proper Turn on the power Button on the remote control unit to turn on the powerOperation Before operatingTo select the input mode from main unit To select the input mode from the remote control unitInput mode selection function Playing the input sourceAdjusting the sound quality tone After starting playbackDolby Digital DTSTurning the sound off temporarily muting Listening over headphonesChecking the currently playing program source, etc Mode AUTO, PCM, DTS or Analog button to switch to Playback using the external input EXT. in jacksFollow to 3 under Playing the input source Surround Adjust the level of the selected speakerBefore playing with the surround function Dolby Surround Pro Logic II mode Dolby PRO LogicDimension setting Center Width settingDefault setting Surround parameters q Pro Logic II ModeCinema EQ OFF Dolby PLII, Dolby PROLOGIC, Dolby DIGITAL, DTSDefault COMP. OFFSurround parameters w Cinema EQ. Cinema Equalizer COMP. Dynamic Range CompressionSurround modes and their features DSP Surround SimulationVideo Game Personal Memory PlusRoom Size MED Effect LevelDSP surround simulation Use Left Right buttons to set the room size InitialDefault Y/N Use Left Right buttons to set the delay time InitialWhen press the Down button When press the UP buttonPress the Surround Parameter button Surround parameters e Surround modes and parametersAuto preset memory Listening to the RadioManual tuning Auto tuningSet the input function to Tuner Preset stations Recalling preset stationsLast Function Memory Initialization of the MicroprocessorAdditional Information Speaker setting examplesSurround Dolby Digital compatible media and playback methods Dolby Digital and Dolby Pro LogicDolby Pro Logic DTS Digital Surround DTS compatible media and playback methodsTroubleshooting Specifications Audio sectionMono StereoVDP List of Preset Codes / Liste DE Codes Préréglés DVDVCR Francais English 16-11, Yushima 3-CHOME, BUNKYOU-KU, Tokyo 113-0034, Japan Page Page Page