Denon AVR-1403, 483 manual Comp. Off, Default, Surround parameters w Cinema EQ. Cinema Equalizer

Page 33

ENGLISH

6

Use the

(left) and

(right) buttons to set the D. COMP.

 

 

 

 

 

(Initial)

 

 

 

 

 

 

OFF

LOW

MID

HIGH

 

(Remote control unit)

D.COMP. OFF

 

 

 

 

 

 

 

 

 

 

 

 

(left) button

(right) button

 

SURROUND

 

 

 

NOTE:

 

 

 

 

 

 

 

MENU

Press the SURROUND or

(down) button to switch to the LFE This parameter is not displayed

setting.

during DTS playback.

(Remote control unit)

7

Use the

(left) and

(right) buttons to set the LFE level.

 

LFE 0dB

(Remote control unit)

•The level can be adjusted in units of 1 dB from –10 to 0 dB.

Set to the desired level according to the speaker systems being used and the source to be played.

 

SURROUND

 

 

 

 

 

 

Press the SURROUND or

(down) button to switch to the default setting.

 

 

MENU

 

 

 

 

 

8

(Remote control unit)

 

 

 

 

 

To reset the settings to the factory defaults, use the

(left) and

(right) buttons to display “Yes”.

 

 

DEFAULT

Y/N

 

YES

NO

 

 

 

 

 

(Remote control unit)

 

 

(left) button

(right) button

 

 

 

 

SURROUND

Press the SURROUND or (down) button to switch to the CINEMA EQ. setting.

MENU

(Remote control unit)

NOTE:

•When making parameter settings, the display will return to the regular condition several seconds after the last button was pressed and the setting will be completed.

Surround parameters w

CINEMA EQ. (Cinema Equalizer):

The Cinema EQ function gently decreases the level of the extreme high frequencies, compensating for overly-bright sounding motion picture soundtracks. Select this function if the sound from the front speakers is too bright.

This function only works in the Dolby Pro Logic, Dolby Digital and DTS Surroundmodes. (The same contents are set for all operating modes.)

D.COMP. (Dynamic Range Compression):

Motion picture soundtracks have tremendous dynamic range (the contrast between very soft and very loud sounds). For listening late at night, or whenever the maximum sound level is lower than usual, the Dynamic Range Compression allows you to hear all of the sounds in the soundtrack (but with reduced dynamic range). (This only works when playing program sources recorded in Dolby Digital.) Select one of the four parameters (“OFF”, “LOW”, “MID” (middle) or “HI” (high)). Set to OFF for normal listening.

LFE (Low Frequency Effect):

Program source and adjustment range

1.Dolby Digital: –10 dB to 0 dB

2.DTS Surround: –10 dB to 0 dB

When Dolby Digital encoded software is played, it is recommended that the LFE LEVEL be set to 0 dB for correct Dolby Digital playback.

When DTS encoded movie software is played, it is recommended that the LFE LEVEL be set to 0 dB for correct DTS playback. When DTS encoded music software is played, it is recommended that the LFE LEVEL be set to -10 dB for correct DTS playback.

33

Page 32 Page 34
Image 33
Page 32 Page 34
Contents Nous vous remercions pour l’achat de cet appareil AVR-1403/483English Francais Safety Instructions Before Using Table of ContentsFeatures Front Panel Part Names and FunctionsSystem System SET UP Remote control unitSetting UP the Speaker Systems Finally, setting up the systemRead this First Connections Connecting the audio componentsUse the AC Outlet for audio equipment only. Do not use It for hair driers, etcAudio OUT Video OUT Connecting the video equipmentsConnecting a Video game equipment AM loop antenna assembly Connecting the antenna terminalsConnecting the speaker cords Speaker system connectionsSpeaker Impedance Protector circuit Using the Remote Control Unit Range of operation of the remote control unitInserting the batteries Use the following buttons to set up the system Setting UP the SystemFront Large System SET UPCenter Small SURR. SmallSW Mode Norm Setting the Subwoofer ModeWoofer YES Setting the speaker distance PreparationsListening position After setting up the system Digital input setupCoax DVD Terminal InitialRemote Control Unit Preset memory Audio componentOperating Denon audio components Preset memory Video component For DVD player Operating a video component stored in the preset memoryFor video disc player VDP For video deck VCRButton on the remote control unit to turn on the power Check that all connections are proper Turn on the powerOperation Before operatingTo select the input mode from the remote control unit To select the input mode from main unitInput mode selection function Playing the input sourceAfter starting playback Adjusting the sound quality toneDolby Digital DTSListening over headphones Turning the sound off temporarily mutingChecking the currently playing program source, etc Playback using the external input EXT. in jacks Mode AUTO, PCM, DTS or Analog button to switch toFollow to 3 under Playing the input source Adjust the level of the selected speaker SurroundBefore playing with the surround function Dolby PRO Logic Dolby Surround Pro Logic II modeCenter Width setting Dimension settingDefault setting Surround parameters q Pro Logic II ModeDolby PLII, Dolby PROLOGIC, Dolby DIGITAL, DTS Cinema EQ OFFCOMP. OFF DefaultSurround parameters w Cinema EQ. Cinema Equalizer COMP. Dynamic Range CompressionDSP Surround Simulation Surround modes and their featuresVideo Game Personal Memory PlusEffect Level Room Size MEDDSP surround simulation Use Left Right buttons to set the room size InitialUse Left Right buttons to set the delay time Initial Default Y/NWhen press the UP button When press the Down buttonPress the Surround Parameter button Surround modes and parameters Surround parameters eListening to the Radio Auto preset memoryAuto tuning Manual tuningSet the input function to Tuner Recalling preset stations Preset stationsInitialization of the Microprocessor Last Function MemorySpeaker setting examples Additional InformationSurround Dolby Digital and Dolby Pro Logic Dolby Digital compatible media and playback methodsDolby Pro Logic DTS compatible media and playback methods DTS Digital SurroundTroubleshooting Audio section SpecificationsMono StereoList of Preset Codes / Liste DE Codes Préréglés DVD VDPVCR Francais English 16-11, Yushima 3-CHOME, BUNKYOU-KU, Tokyo 113-0034, Japan Page Page Page
Top Page Image Contents