Frymaster ESW, 17ECS, EWBS manual Reverse Steps 1-7 to complete the procedure

Page 40

2.If rigid water connections have been used, disconnect the cooker from the incoming water supply.

3.Remove the basket lift arms from the lifter rods and then reposition the cooker to gain access to the rear. Remove the upper and lower basket lift rear panels.

4.Unplug the basket lift wiring harness from the lower 6-pin connector on the component box. (To do this, you must reach around behind the component box from the front of the cooker.)

Disconnect basket lift wiring harness from this connector.

5.Disconnect the basket lift link from the lifter cam (bell crank) assemblies one at a time. When the link is disconnected from a cam, slip the corresponding lifter rod down and out of the assembly (see illustration below).

Lifter Rods

Link

Disconnect the basket lift link from the lifter cams and slip the lifter rods down and out of the assembly.

6.Remove the four bolts securing the motor mount to the frame, then remove the motor and mount assembly from the unit. NOTE: It is possible to replace a motor or the microswitch without removing the motor and mount assembly, but it is much more difficult.

7.Dismount the motor or microswitch as shown below and install the replacement.

NOTE: The right motor dismounts

in the same way as the left.

Loosen setscrew in bottom of cam (bell crank).

8. Reverse Steps 1-7 to complete the procedure.

6-8

Page 39 Page 41
Image 40
Page 39 Page 41
Contents Hour Service Hotline Page Preventive Maintenance ESW/EWBS Service Procedures & Parts Page This page Intentionally Left Blank Parts Ordering and Service Information Safety InformationEquipment Description Qualified Service Personnel Qualified Installation PersonnelQualified AND/OR Authorized Operating Personnel What to do if your equipment arrives damaged General Installation Requirements National Code RequirementsElectrical Grounding Requirements FCC ComplianceCaster/Leg Installation Pre-Connection PreparationsConnecting to the Electrical Supply Use copper wire ONLY, suitable for at least 170ºF 75ºCWatts Per leg Wire Size Electric Cooker Models 17EC, 17ECS, ESW, & EwbsField Connection Wiring Diagrams Introduction Computers are not interchangeableSetting the Controller Transition Temperature/Boil Intensity Operating InstructionsAltitude Boiling Point Controller Simmer Mode Adjustment Toggling Between Fahrenheit and Celsius Temperature DisplayShutting the 17EC/17ECS Down Start-Up ProcedureComputer Magic III Controller As Used on Ewbs Units Setting the Unit UP for FIRST-TIME Operation Operating the Computer Selecting FAHRENHEIT- Celsius Display Mode Selecting Boil or Simmer Mode Shutting the Ewbs with CM III Computer DownBoiling Out the Cookpot Page This page Intentionally Left Blank Daily Preventive Maintenance Inspect Equipment and Accessories for DamageThis page Intentionally Left Blank Before calling a servicer or the Frymaster Hotline Operator Troubleshooting Guide Problem Probable Causes Corrective ActionTroubleshooting Guide Replacing Fuses in 17EC and 17ECS Models Functional Description Replacing Equipment Components Replacing the Computer Replacing Electronic Components Other than the ComputerReplacing a Heating Element Replacing the High-Limit Thermostat Replacing the Temperature Probe Replacing a Water-Level SensorReplacing the Pressure Regulator or Solenoid Valve Replacing a Basket Lift Motor or Microswitch Replacing the Water FaucetReverse Steps 1-7 to complete the procedure Replacing the Cookpot or Rinse Tank How the Power-Supply System Works TroubleshootingHow the Computer Works How the Autofill/AutoSkim System Works How the Water Heating System WorksHow the Basket Lift System Works Technician Troubleshooting Guides Troubleshooting the 24VAC Power Supply SystemTroubleshooting the 24VAC Power Supply to the Computer Troubleshooting the Autofill System Begin to fill?Troubleshooting the Water Heating System Probe ThermostatTroubleshooting the Basket Lift System OK?This page Intentionally Left Blank Parts List ComponentComponents Component Cabinetry Component Cookpot Rinse TankComponent Electronics Component Water Supply System Components Wiring Diagram 17ECS Computer ControlWiring Diagrams 17EMCS Page This page Intentionally Left Blank Units with Manual Controls rocker-switches and a thermostat Units with Computer Controls Replacing Equipment Components Replacing the Computer Replacing the Heating Element Hole Lead Replacing a Water-Level Sensor Attach wire15C here Attach wires 20C and 35C here Typical Water Supply System Configurations Reverse Steps 1-4 to complete the procedure Replacing the Cookpot On units with manual thermostat controlsRemove these screws Troubleshooting How the Autofill and Skim Systems Work How the Basket Lift System Works Position. Replace switch as required Controls? Checking HIGH-LIMIT Thermostat Temperature Probe Line voltage present at the Common Replace Cover Lift Component Disproportionately large for clarity 910-7377 Control Components Cookpot and Drain Components Electronics Component Supply Component Wiring Diagrams Remove this Cover to Inspect Field WiringUnits With ComputersService Hotline

17EC, 17ECS, EWBS, ESW specifications

Frymaster, a leader in the foodservice equipment industry, offers a range of fryers designed to enhance productivity and quality in commercial kitchens. Among these, the Frymaster ESW, EWBS, 17ECS, and 17EC models stand out due to their innovative features, advanced technologies, and user-friendly designs.

The Frymaster ESW fryer is engineered for high-efficiency frying while maintaining excellent food quality. It incorporates a built-in oil filtration system, allowing operators to extend the life of oil, reduce frying costs, and ensure consistent product quality. The ESW is designed with energy efficiency in mind, which not only minimizes operational costs but also helps restaurants reduce their environmental footprint. Its programmable controls enable seamless operation, and the easy-to-read display assists staff in monitoring frying times, temperatures, and oil conditions.

The EWBS model is equipped with a robust design that focuses on convenience and reliability. One of its key features is its large fry pot, which enables high-capacity frying, reducing cooking time and increasing output during peak hours. The EWBS fryer also maximizes versatility, allowing operators to prepare a wide variety of menu items. It features adjustable frying baskets, which are designed to accommodate foods of different sizes. Additionally, the model includes energy-efficient burners that result in quicker recovery times and lower gas consumption.

The 17ECS and 17EC models are designed for compact spaces without sacrificing performance. Featuring digital controls and simplified interfaces, they provide operators with precise temperature management. The 17ECS is known for its superior oil management system, which enhances oil life and maintains food quality. The 17EC, on the other hand, offers a variety of programmable cooking options, making it ideal for establishment with diverse culinary needs.

Both the 17ECS and 17EC also emphasize safety, incorporating features such as automatic shutoff and cool-touch handles, which help prevent burns and accidents in fast-paced kitchen environments. These fryers are built with durable materials that ensure longevity, making them a worthy investment for any restaurant or foodservice operation.

Together, the Frymaster ESW, EWBS, 17ECS, and 17EC models represent a commitment to innovation in commercial frying technology, combining energy efficiency, user-friendly interfaces, and versatile cooking capabilities that cater to the needs of modern kitchens. As restaurants continue to evolve, these fryers provide the reliability and performance necessary to meet demand and maintain high-quality standards.
Top Page Image Contents