Frymaster 17ECS, ESW How the Autofill and Skim Systems Work, How the Water Heating System Works

Page 77

7.4.3 How the Autofill and Skim Systems Work

The heart of the automatic filling (Autofill) system is a normally closed solenoid valve that opens when 24VAC is applied as a result of the loss of upper water-level sensor ground. The ground is lost when the sensor is not in contact with water in the cookpot. Starch or lime build-up on the sensor may keep a ground from forming. Therefore always make sure the sensor is clean and its lead is firmly connected to Pin 1 of the 6-pin connector on the interface board (units with manual controls) or connector J5 on the interface board (units with computer controls). Also, in order for the ground to form, there must be some mineral content in the water (pure water is non-conductive). Consequently, the units will not operate with distilled water. If distilled, highly filtered, or purified water is used, add ⅛-cup of baking soda to the water each time the cookpot is emptied and refilled.

In units with manual controls, the 24VAC is supplied via Pins 1 and 2 of the 4-pin connector on the interface board so long as the upper water-level sensor is not in contact with the water in the cookpot. In units with computer controls, 24VAC is continuously supplied to one leg of the circuit via Pin 6 of the 15-pin connector on the front of the contactor box. The other leg is supplied via Pin 2 of the 12-pin connector on the interface board so long as the upper water-level sensor is not in contact with water in the cookpot. In either case, when the water in the cookpot reaches the upper water-level sensor, the sensor is grounded. This causes logic circuits in the interface board to cut the 24VAC to the solenoid, closing the valve.

If the SKIM switch is placed in the ON position, the logic circuits in the interface board are bypassed and 24VAC is applied to the solenoid valve for as long as the switch is left in the ON position.

7.4.4 How the Water Heating System Works

To prevent energizing the heating elements when there is no water in the cookpot, these units are equipped with a low-water-level sensor. This sensor must be grounded by contact with water in the cookpot before the control circuitry will apply power to the elements. Starch or lime build-up on the low-water-level sensor may keep the ground from forming, therefore always make sure the sensor is clean and its lead is firmly connected to J5 on the interface board. In order for the ground to form, there must be some mineral content in the water (pure water is non-conductive). Consequently, the units will not operate with distilled water. If distilled, highly filtered, or purified water is used, add ⅛-cup of baking soda to the water each time the cookpot is emptied and refilled.

In addition to the low-water-level sensor discussed above, the water heating system has six more parts: the high-limit thermostat, the temperature probe, the contactor, the element, and a HEAT CYCLE switch and manual thermostat, or a computer.

The high-limit thermostat functions as a normally closed switch. If the water in the cookpot falls below the low-water-level sensor but the sensor remains grounded (for whatever reason), the high- limit switch will open when the element temperature reaches 400ºF ±15 (204ºC ± 9). This cuts power to the contactor coil and thus to the element.

The temperature probe is used only when the unit is in the simmer mode. When the operator selects the simmer mode, logic circuits in the on the interface board or in the computer monitor the temperature of the water and cycle power to the element (via the contactor coil) on and off as

7-13

Image 77
Contents Hour Service Hotline Page Preventive Maintenance ESW/EWBS Service Procedures & Parts Page This page Intentionally Left Blank Safety Information Parts Ordering and Service InformationEquipment Description Qualified AND/OR Authorized Operating Personnel Qualified Installation PersonnelQualified Service Personnel What to do if your equipment arrives damaged National Code Requirements General Installation RequirementsElectrical Grounding Requirements FCC CompliancePre-Connection Preparations Caster/Leg InstallationUse copper wire ONLY, suitable for at least 170ºF 75ºC Connecting to the Electrical SupplyWatts Per leg Wire Size Electric Cooker Models 17EC, 17ECS, ESW, & EwbsField Connection Wiring Diagrams Computers are not interchangeable IntroductionOperating Instructions Setting the Controller Transition Temperature/Boil IntensityAltitude Boiling Point Toggling Between Fahrenheit and Celsius Temperature Display Controller Simmer Mode AdjustmentComputer Magic III Controller As Used on Ewbs Units Start-Up ProcedureShutting the 17EC/17ECS Down Setting the Unit UP for FIRST-TIME Operation Operating the Computer Selecting FAHRENHEIT- Celsius Display Mode Shutting the Ewbs with CM III Computer Down Selecting Boil or Simmer ModeBoiling Out the Cookpot Page This page Intentionally Left Blank Inspect Equipment and Accessories for Damage Daily Preventive MaintenanceThis page Intentionally Left Blank Before calling a servicer or the Frymaster Hotline Problem Probable Causes Corrective Action Operator Troubleshooting GuideTroubleshooting Guide Replacing Fuses in 17EC and 17ECS Models Functional Description Replacing Electronic Components Other than the Computer Replacing Equipment Components Replacing the ComputerReplacing a Heating Element Replacing the High-Limit Thermostat Replacing a Water-Level Sensor Replacing the Temperature ProbeReplacing the Pressure Regulator or Solenoid Valve Replacing the Water Faucet Replacing a Basket Lift Motor or MicroswitchReverse Steps 1-7 to complete the procedure Replacing the Cookpot or Rinse Tank How the Computer Works TroubleshootingHow the Power-Supply System Works How the Water Heating System Works How the Autofill/AutoSkim System WorksHow the Basket Lift System Works Troubleshooting the 24VAC Power Supply System Technician Troubleshooting GuidesTroubleshooting the 24VAC Power Supply to the Computer Begin to fill? Troubleshooting the Autofill SystemProbe Thermostat Troubleshooting the Water Heating SystemOK? Troubleshooting the Basket Lift SystemThis page Intentionally Left Blank Component Parts ListComponents Component Cabinetry Component Rinse Tank CookpotComponent Electronics Component Water Supply System Components Computer Control Wiring Diagram 17ECSWiring Diagrams 17EMCS Page This page Intentionally Left Blank Units with Manual Controls rocker-switches and a thermostat Units with Computer Controls Replacing Equipment Components Replacing the Computer Replacing the Heating Element Hole Lead Replacing a Water-Level Sensor Attach wire15C here Attach wires 20C and 35C here Typical Water Supply System Configurations Reverse Steps 1-4 to complete the procedure On units with manual thermostat controls Replacing the CookpotRemove these screws Troubleshooting How the Autofill and Skim Systems Work How the Basket Lift System Works Position. Replace switch as required Controls? Checking HIGH-LIMIT Thermostat Temperature Probe Line voltage present at the Common Replace Cover Lift Component Disproportionately large for clarity 910-7377 Control Components Cookpot and Drain Components Electronics Component Supply Component Remove this Cover to Inspect Field Wiring Wiring DiagramsWith Computers UnitsService Hotline

17EC, 17ECS, EWBS, ESW specifications

Frymaster, a leader in the foodservice equipment industry, offers a range of fryers designed to enhance productivity and quality in commercial kitchens. Among these, the Frymaster ESW, EWBS, 17ECS, and 17EC models stand out due to their innovative features, advanced technologies, and user-friendly designs.

The Frymaster ESW fryer is engineered for high-efficiency frying while maintaining excellent food quality. It incorporates a built-in oil filtration system, allowing operators to extend the life of oil, reduce frying costs, and ensure consistent product quality. The ESW is designed with energy efficiency in mind, which not only minimizes operational costs but also helps restaurants reduce their environmental footprint. Its programmable controls enable seamless operation, and the easy-to-read display assists staff in monitoring frying times, temperatures, and oil conditions.

The EWBS model is equipped with a robust design that focuses on convenience and reliability. One of its key features is its large fry pot, which enables high-capacity frying, reducing cooking time and increasing output during peak hours. The EWBS fryer also maximizes versatility, allowing operators to prepare a wide variety of menu items. It features adjustable frying baskets, which are designed to accommodate foods of different sizes. Additionally, the model includes energy-efficient burners that result in quicker recovery times and lower gas consumption.

The 17ECS and 17EC models are designed for compact spaces without sacrificing performance. Featuring digital controls and simplified interfaces, they provide operators with precise temperature management. The 17ECS is known for its superior oil management system, which enhances oil life and maintains food quality. The 17EC, on the other hand, offers a variety of programmable cooking options, making it ideal for establishment with diverse culinary needs.

Both the 17ECS and 17EC also emphasize safety, incorporating features such as automatic shutoff and cool-touch handles, which help prevent burns and accidents in fast-paced kitchen environments. These fryers are built with durable materials that ensure longevity, making them a worthy investment for any restaurant or foodservice operation.

Together, the Frymaster ESW, EWBS, 17ECS, and 17EC models represent a commitment to innovation in commercial frying technology, combining energy efficiency, user-friendly interfaces, and versatile cooking capabilities that cater to the needs of modern kitchens. As restaurants continue to evolve, these fryers provide the reliability and performance necessary to meet demand and maintain high-quality standards.