Frymaster ESW, 17ECS, EWBS manual Replacing a Heating Element

Page 35

5.Replace the component box covers, being sure to reconnect the ground wire. Reconnect the cooker to the electrical power supply.

6.3.3Replacing a Heating Element

1.Drain the cookpot and disconnect the cooker from the electrical power supply. Disconnect the unit from the water supply at the rear of the cooker. Remove the basket lift arms from the unit.

2.Reposition the cooker to allow clear access to the rear of the unit. Remove the upper and lower basket lift panels.

3.Unplug the element connector from the rear of the component box. Depress the locking tabs on each side of the connector and extend the connector to release the element leads (see photo at right). Pull each of the leads out of the connector, being careful not to damage the connector in the process.

4.If the bundle of element leads is enclosed in a fiberglass insulating sheath, cut the wire ties securing the sheath in place, and remove and discard it; it is no longer required. If replacing the left element (as viewed from the front of the cooker), cut the metal wire ties that secure the high-limit thermostat to the element, being careful not to bend the thermostat in the process.

5.Remove the brass nuts that secure the element in the cookpot and lift the failed element from the cookpot. Recover the Teflon washers from the failed element for use on the replacement.

Remove these nuts to remove

element from cookpot.

Standoffs

6.Position the replacement element in the cookpot with the standoffs on the bottom of the cookpot. Thread the element leads through the Teflon washers recovered from the failed element. Secure the element in place with the nuts removed in Step 5.

7.If the left element (as viewed from the front of the cooker) was replaced, secure the high-limit thermostat against the inside of the leg of the element with two metal wire ties.

6-3

Page 34 Page 36
Image 35
Page 34 Page 36
Contents Hour Service Hotline Page Preventive Maintenance ESW/EWBS Service Procedures & Parts Page This page Intentionally Left Blank Safety Information Parts Ordering and Service InformationEquipment Description Qualified AND/OR Authorized Operating Personnel Qualified Installation PersonnelQualified Service Personnel What to do if your equipment arrives damaged FCC Compliance General Installation RequirementsNational Code Requirements Electrical Grounding RequirementsPre-Connection Preparations Caster/Leg InstallationElectric Cooker Models 17EC, 17ECS, ESW, & Ewbs Connecting to the Electrical SupplyUse copper wire ONLY, suitable for at least 170ºF 75ºC Watts Per leg Wire SizeField Connection Wiring Diagrams Computers are not interchangeable IntroductionOperating Instructions Setting the Controller Transition Temperature/Boil IntensityAltitude Boiling Point Toggling Between Fahrenheit and Celsius Temperature Display Controller Simmer Mode AdjustmentComputer Magic III Controller As Used on Ewbs Units Start-Up ProcedureShutting the 17EC/17ECS Down Setting the Unit UP for FIRST-TIME Operation Operating the Computer Selecting FAHRENHEIT- Celsius Display Mode Shutting the Ewbs with CM III Computer Down Selecting Boil or Simmer ModeBoiling Out the Cookpot Page This page Intentionally Left Blank Inspect Equipment and Accessories for Damage Daily Preventive MaintenanceThis page Intentionally Left Blank Before calling a servicer or the Frymaster Hotline Problem Probable Causes Corrective Action Operator Troubleshooting GuideTroubleshooting Guide Replacing Fuses in 17EC and 17ECS Models Functional Description Replacing Electronic Components Other than the Computer Replacing Equipment Components Replacing the ComputerReplacing a Heating Element Replacing the High-Limit Thermostat Replacing a Water-Level Sensor Replacing the Temperature ProbeReplacing the Pressure Regulator or Solenoid Valve Replacing the Water Faucet Replacing a Basket Lift Motor or MicroswitchReverse Steps 1-7 to complete the procedure Replacing the Cookpot or Rinse Tank How the Computer Works TroubleshootingHow the Power-Supply System Works How the Water Heating System Works How the Autofill/AutoSkim System WorksHow the Basket Lift System Works Troubleshooting the 24VAC Power Supply System Technician Troubleshooting GuidesTroubleshooting the 24VAC Power Supply to the Computer Begin to fill? Troubleshooting the Autofill SystemProbe Thermostat Troubleshooting the Water Heating SystemOK? Troubleshooting the Basket Lift SystemThis page Intentionally Left Blank Component Parts ListComponents Component Cabinetry Component Rinse Tank CookpotComponent Electronics Component Water Supply System Components Computer Control Wiring Diagram 17ECSWiring Diagrams 17EMCS Page This page Intentionally Left Blank Units with Manual Controls rocker-switches and a thermostat Units with Computer Controls Replacing Equipment Components Replacing the Computer Replacing the Heating Element Hole Lead Replacing a Water-Level Sensor Attach wire15C here Attach wires 20C and 35C here Typical Water Supply System Configurations Reverse Steps 1-4 to complete the procedure On units with manual thermostat controls Replacing the CookpotRemove these screws Troubleshooting How the Autofill and Skim Systems Work How the Basket Lift System Works Position. Replace switch as required Controls? Checking HIGH-LIMIT Thermostat Temperature Probe Line voltage present at the Common Replace Cover Lift Component Disproportionately large for clarity 910-7377 Control Components Cookpot and Drain Components Electronics Component Supply Component Remove this Cover to Inspect Field Wiring Wiring DiagramsWith Computers UnitsService Hotline

17EC, 17ECS, EWBS, ESW specifications

Frymaster, a leader in the foodservice equipment industry, offers a range of fryers designed to enhance productivity and quality in commercial kitchens. Among these, the Frymaster ESW, EWBS, 17ECS, and 17EC models stand out due to their innovative features, advanced technologies, and user-friendly designs.

The Frymaster ESW fryer is engineered for high-efficiency frying while maintaining excellent food quality. It incorporates a built-in oil filtration system, allowing operators to extend the life of oil, reduce frying costs, and ensure consistent product quality. The ESW is designed with energy efficiency in mind, which not only minimizes operational costs but also helps restaurants reduce their environmental footprint. Its programmable controls enable seamless operation, and the easy-to-read display assists staff in monitoring frying times, temperatures, and oil conditions.

The EWBS model is equipped with a robust design that focuses on convenience and reliability. One of its key features is its large fry pot, which enables high-capacity frying, reducing cooking time and increasing output during peak hours. The EWBS fryer also maximizes versatility, allowing operators to prepare a wide variety of menu items. It features adjustable frying baskets, which are designed to accommodate foods of different sizes. Additionally, the model includes energy-efficient burners that result in quicker recovery times and lower gas consumption.

The 17ECS and 17EC models are designed for compact spaces without sacrificing performance. Featuring digital controls and simplified interfaces, they provide operators with precise temperature management. The 17ECS is known for its superior oil management system, which enhances oil life and maintains food quality. The 17EC, on the other hand, offers a variety of programmable cooking options, making it ideal for establishment with diverse culinary needs.

Both the 17ECS and 17EC also emphasize safety, incorporating features such as automatic shutoff and cool-touch handles, which help prevent burns and accidents in fast-paced kitchen environments. These fryers are built with durable materials that ensure longevity, making them a worthy investment for any restaurant or foodservice operation.

Together, the Frymaster ESW, EWBS, 17ECS, and 17EC models represent a commitment to innovation in commercial frying technology, combining energy efficiency, user-friendly interfaces, and versatile cooking capabilities that cater to the needs of modern kitchens. As restaurants continue to evolve, these fryers provide the reliability and performance necessary to meet demand and maintain high-quality standards.
Top Page Image Contents