Frymaster H50 manual Replacing the Frypot

Page 21

3.Position a container beneath the oil return fitting at the front of the cabinet. Disconnect the flexible oil line from the fitting, allowing any residual oil to drain into the container.

4.At the rear of the fryer, unplug the left connector (as viewed from the rear of the fryer) from the transformer box. Using a pin pusher, push the pump solenoid valve wires from Pins 7 and 9.

5.Remove the four nuts and bolts attaching the motor mount to the rear motor mount support.

6.At the front of the fryer, remove the cover plate from the front of the motor and disconnect the motor wires.

7.Place a 1-foot (30.5-cm) length of wood (or similar support) beneath the motor mount near the front of the unit and remove the two remaining nuts and bolts attaching the motor mount to the front cabinet cross-brace.

8.Carefully remove the support and lower the motor mount to the floor, allowing the rear of the mount to slide forward and off the rear motor mount support.

9.Disconnect the Power Shower flexline (if applicable) or the oil return flexline from the pump. The motor and pump assembly can now be pulled from beneath the fryer and the failed component can be removed and replaced.

10.Position the new/repaired motor and pump assembly beneath the fryer and reconnect the Power Shower flexline (if applicable) or the oil return flexline to the pump. Lift the rear of the motor mount up and onto the rear motor mount support.

11.Lift the front of the motor mount up and support it with a 1-foot (30.5-cm) piece of wood or a similar support. Install but do not tighten the two nuts and bolts that attach the motor mount to the front cabinet cross-brace.

12.Install and tighten the four nuts and bolts that secure the motor mount to the rear motor mount support. Reconnect the solenoid valve wires to Pins 7 and 9 of the 9-pin connector (polarity does not matter) and reconnect the plug.

13.At the front of the fryer, tighten the two nuts and bolts at the front of the motor mount. Reconnect the motor power wires and reinstall the wiring cover plate.

14.Reconnect the oil return flexline and reinstall the filter pan.

15.Reconnect the unit to the electrical power supply, fill the frypots with oil, and check for proper operation.

1.6.10Replacing the Frypot

1.Disconnect the fryer from the electrical and gas supplies.

2.Remove the filter pan from the unit and drain the frypots into a Shortening Disposal Unit (SDU) or other appropriate metal container.

1-16

Page 20 Page 22
Image 21
Page 20 Page 22
Contents 8196083 Hour Service HotlineCanada Page PRO H50/55-SERIES GAS Fryers Table of Contents Parts List Electronic Ignition System Functional DescriptionInterface Board LED Diagnostic LightsInterface Board Frequently Used Test Points for Interface Board Checking the Burner Manifold Gas Pressure Cleaning the Gas Valve Vent TubeNon-CE Standard Burner Manifold Gas Pressures Measuring Flame Current Replacing the Temperature Probe or High-Limit Thermostat Replacing an Ignition Module Replacing the Interface BoardReplacing or Cleaning a Combustion Air Blower Blower Housing Blower Wheel Adjusting the Air/Gas Mixture Page ALL Other Valves Page Replacing the Frypot Page Replacing Frypot Insulation and/or Upper Burner Rails Disassembling a Frypot Full-vat Illustrated Page Page Re-assembling a Frypot Full-vat Illustrated Ignition Failure Troubleshooting and Problem IsolationImproper Burner Function Problems Related to the GAS ValvePage Computer Malfunctions Improper Temperature ControlFiltration Malfunctions Pump Verifying Solenoid Operation LeakageBasket Lift Malfunctions Binds and Jams Interpretation of Analog Controller Lights Troubleshooting Guides Troubleshooting the 24 VAC CircuitPage Volt Circuit Left VAT Right VAT Troubleshooting the Temperature Probe Troubleshooting the Gas ValveProbe Resistance Charts Probe Resistance ChartModule Wiring Diagram for Full-Vat Simplified Wiring DiagramsDiagram WiringFull AustrailiaSingle-Spark VatLeft VAT Right or Full VAT Principal Wiring ConnectionsFull VAT Wiring Diagrams Pro H50/55-Series Fryer, Multi-vatPro H50/55-Series Fryer, Single, Full-vat Pro H50/55-Series Fryer, Single, Dual-vat Pro H50/55-Series Fryer, Single, CE Pro H50/55-Series Fryer, Single, FAST-ready 11.6.2 FPH150/155 Transformer/Filter Box Fpph 250/255/450/455 Transformer/Filter Box Fpph 350/355 Transformer/Filter Box Modular Basket Lift 100/120V Right Side Modular Basket Lift 208/250VPage PRO H50/55-SERIES GAS Fryers Parts List Basket Lift Assemblies Component Cabinetry Backs, Doors, Flue Caps, Sides, and Top Caps Component See Page 2-4 for upper hinges Component 2-inch Hex Washer Manifold, Rear not present in single fryers Full-vatNon-CE Export not available for CE Units ControllersPage Roller, Filter Pan See Note at bottom Drain Valves and Associated Components Component Oil Return Line Components Component Oil Return Handle, Oil Disposal and Disposal Hose Components 810-0783 Cotter Pin 19 810-0285 Swivel, Valve Control Assembly Wand Plumbing Japan Oil Disposal Wand AssemblyNut furnished With Item Rear Flush Oil Return ComponentsElbow, 90º x ½-inch Street Power Shower Assembly, Dual-vat, Complete Power Shower Assemblies OptionalComponent Boxes Electronics and Electrical ComponentsCable, 21-inch Ignition comes with Rajah connector Item Transformer Nut, 8-32 Keps Hex High-Limit Thermostat and Temperature Probe Frypot Components Associated Components Full-VatComponent Dual-Vat Frypot Components For rear flush oil return components, see PH250/255 Full Vat Gas Manifold Typical Gas Supply and Combustion System ComponentsCE Conversion Kits Gas Valves and Associated Components Gas Valve Wiring Wiring Assemblies and Harnesses Main Wiring Harnesses Miscellaneous Connectors and Terminals Ring two required Single H50/55 Filtration System ComponentsBracket, Valve used to attach Item 3 to Item Single H50/55 Oil Return ComponentsSingle H50/55 Component Boxes Single H50/55 High-Limit Thermostat and Temperature Probe Single H50/55 Transformer Boxes Service Hotline
Related manuals
Manual 100 pages 47.98 Kb Manual 70 pages 55.37 Kb

H50 specifications

The Frymaster H50 is a state-of-the-art commercial deep fryer designed for efficiency and reliability in fast-paced kitchen environments. Known for its advanced technology and user-friendly features, the H50 is an ideal solution for restaurants, cafeterias, and food service operations looking to enhance their frying capabilities.

One of the standout features of the Frymaster H50 is its innovative oil management system. This system helps maintain optimal oil quality and reduces the frequency of oil replacement, which not only saves costs but also contributes to improved food flavor. The unit is equipped with a built-in filtration system that can clean the oil while the fryer is in use, significantly extending the life of the frying oil and ensuring consistent frying results.

The Frymaster H50 is also designed with advanced temperature control technology. This ensures precise temperature settings, allowing operators to achieve the perfect fry every time. The fryer features a digital control panel that makes it easy to set and monitor frying temperatures, giving chefs the flexibility to prepare a wide variety of fried foods, from crispy french fries to delicate fish fillets.

In terms of performance, the Frymaster H50 boasts a high production capacity, making it capable of handling large volumes of food. This is especially beneficial during peak service hours when demand is at its highest. The fryer can heat up quickly, providing rapid recovery times that keep up with busy kitchen demands.

Durability and ease of maintenance are also key characteristics of the Frymaster H50. Constructed with high-quality materials, this fryer is built to withstand the rigors of heavy usage in commercial settings. The removable fry pots offer easy access for cleaning and maintenance, ensuring that the fryer stays in optimal working condition with minimal downtime.

Another important aspect of the Frymaster H50 is its energy efficiency. The fryer is designed to consume less energy while still delivering superior frying results, which is an essential factor for businesses looking to reduce their operational costs.

Overall, the Frymaster H50 combines innovative technology with user-friendly features to deliver a high-performing commercial frying solution. Its advanced oil management system, precise temperature control, and durable construction make it an excellent choice for any food service operation looking to elevate their frying capabilities.
Top Page Image Contents