Frymaster H50 manual Improper Temperature Control, Computer Malfunctions

Page 31

If these causes are ruled out, the probable cause is a misadjusted gas valve regulator. Refer to Section 1.4, Checking the Burner Manifold Gas Pressure, for the gas valve adjustment procedure.

1.7.3 Improper Temperature Control

Temperature control, including the melt cycle, is a function of several interrelated components, each of which must operate correctly. The principle component is the temperature probe. Other components include the interface board, the controller, and the ignition module.

Improper temperature control problems can be categorized into melt cycle problems and failure to control at setpoint problems.

MELT CYCLE PROBLEMS

In fryers equipped with analog controls, the melt cycle must be initiated by pressing the melt cycle switch. With all other controllers, initiation of the melt cycle is automatic. Problems may originate from the controller, the temperature probe, or a malfunctioning heat relay on the interface board.

FAILURE TO CONTROL AT SETPOINT

Problems in this category may be caused by the temperature probe, the interface board, or the controller.

1.7.4 Computer Malfunctions

SENSITIVITY OR “STRETCH AND SHRINK TIME.”

Sensitivity – “stretch time” – is a programmable feature, patented by Frymaster, which increases or decreases the cook time countdown based on variations in the oil temperature from the set point.

The sensitivity for each product button has ten settings (0 through 9). A sensitivity setting of zero will disable the feature (no change in cooking time), while a nine will provide the highest sensitivity or most change. The correct sensitivity for any product is based on the product, its density, the set point temperature, and the customer’s own requirements. A chart is provided in the Frymaster Fryer Controllers User’s Manual included with your fryer to assist you in setting sensitivity.

RECOVERY TIME

Recovery time – is a method of measuring a fryer’s performance. It is the time required for the fryer to increase the oil temperature from 250ºF to 300ºF (121ºC to 149ºC). This range is used as a standard since ambient kitchen temperatures can effect the test if lower ranges are used.

The Computer Magic III.5 performs the recovery test each time the fryer warms up. An operator can view the results of the test any time the fryer is above the 300ºF (149ºC) point by pressing the button and entering the code 1652. The test results will be displayed in the computer’s LED panel in minutes and seconds. The maximum acceptable recovery time for Pro H55-Series gas fryers is two minutes and twenty-five seconds.

1-26

Page 30 Page 32
Image 31
Page 30 Page 32
Contents 8196083 Hour Service HotlineCanada Page PRO H50/55-SERIES GAS Fryers Table of Contents Parts List Electronic Ignition System Functional DescriptionInterface Board LED Diagnostic LightsInterface Board Frequently Used Test Points for Interface Board Checking the Burner Manifold Gas Pressure Cleaning the Gas Valve Vent TubeNon-CE Standard Burner Manifold Gas Pressures Measuring Flame Current Replacing the Temperature Probe or High-Limit Thermostat Replacing an Ignition Module Replacing the Interface BoardReplacing or Cleaning a Combustion Air Blower Blower Housing Blower Wheel Adjusting the Air/Gas Mixture Page ALL Other Valves Page Replacing the Frypot Page Replacing Frypot Insulation and/or Upper Burner Rails Disassembling a Frypot Full-vat Illustrated Page Page Re-assembling a Frypot Full-vat Illustrated Ignition Failure Troubleshooting and Problem IsolationImproper Burner Function Problems Related to the GAS ValvePage Computer Malfunctions Improper Temperature ControlFiltration Malfunctions Pump Leakage Verifying Solenoid OperationBasket Lift Malfunctions Binds and Jams Interpretation of Analog Controller Lights Troubleshooting Guides Troubleshooting the 24 VAC CircuitPage Volt Circuit Left VAT Right VAT Troubleshooting the Temperature Probe Troubleshooting the Gas ValveProbe Resistance Charts Probe Resistance ChartModule Wiring Diagram for Full-Vat Simplified Wiring DiagramsAustrailia WiringDiagram FullSingle-Spark VatLeft VAT Right or Full VAT Principal Wiring ConnectionsFull VAT Wiring Diagrams Pro H50/55-Series Fryer, Multi-vatPro H50/55-Series Fryer, Single, Full-vat Pro H50/55-Series Fryer, Single, Dual-vat Pro H50/55-Series Fryer, Single, CE Pro H50/55-Series Fryer, Single, FAST-ready 11.6.2 FPH150/155 Transformer/Filter Box Fpph 250/255/450/455 Transformer/Filter Box Fpph 350/355 Transformer/Filter Box Modular Basket Lift 100/120V Right Side Modular Basket Lift 208/250VPage PRO H50/55-SERIES GAS Fryers Parts List Basket Lift Assemblies Component Cabinetry Backs, Doors, Flue Caps, Sides, and Top Caps Component See Page 2-4 for upper hinges Component 2-inch Hex Washer Manifold, Rear not present in single fryers Full-vatNon-CE Export not available for CE Units ControllersPage Roller, Filter Pan See Note at bottom Drain Valves and Associated Components Component Oil Return Line Components Component Oil Return Handle, Oil Disposal and Disposal Hose Components 810-0783 Cotter Pin 19 810-0285 Swivel, Valve Control Assembly Wand Plumbing Japan Oil Disposal Wand AssemblyNut furnished With Item Rear Flush Oil Return ComponentsElbow, 90º x ½-inch Street Power Shower Assembly, Dual-vat, Complete Power Shower Assemblies OptionalComponent Boxes Electronics and Electrical ComponentsCable, 21-inch Ignition comes with Rajah connector Item Transformer Nut, 8-32 Keps Hex High-Limit Thermostat and Temperature Probe Frypot Components Associated Components Full-VatComponent Dual-Vat Frypot Components For rear flush oil return components, see PH250/255 Full Vat Gas Manifold Typical Gas Supply and Combustion System ComponentsCE Conversion Kits Gas Valves and Associated Components Gas Valve Wiring Wiring Assemblies and Harnesses Main Wiring Harnesses Miscellaneous Connectors and Terminals Ring two required Single H50/55 Filtration System ComponentsBracket, Valve used to attach Item 3 to Item Single H50/55 Oil Return ComponentsSingle H50/55 Component Boxes Single H50/55 High-Limit Thermostat and Temperature Probe Single H50/55 Transformer Boxes Service Hotline
Related manuals
Manual 100 pages 47.98 Kb Manual 70 pages 55.37 Kb

H50 specifications

The Frymaster H50 is a state-of-the-art commercial deep fryer designed for efficiency and reliability in fast-paced kitchen environments. Known for its advanced technology and user-friendly features, the H50 is an ideal solution for restaurants, cafeterias, and food service operations looking to enhance their frying capabilities.

One of the standout features of the Frymaster H50 is its innovative oil management system. This system helps maintain optimal oil quality and reduces the frequency of oil replacement, which not only saves costs but also contributes to improved food flavor. The unit is equipped with a built-in filtration system that can clean the oil while the fryer is in use, significantly extending the life of the frying oil and ensuring consistent frying results.

The Frymaster H50 is also designed with advanced temperature control technology. This ensures precise temperature settings, allowing operators to achieve the perfect fry every time. The fryer features a digital control panel that makes it easy to set and monitor frying temperatures, giving chefs the flexibility to prepare a wide variety of fried foods, from crispy french fries to delicate fish fillets.

In terms of performance, the Frymaster H50 boasts a high production capacity, making it capable of handling large volumes of food. This is especially beneficial during peak service hours when demand is at its highest. The fryer can heat up quickly, providing rapid recovery times that keep up with busy kitchen demands.

Durability and ease of maintenance are also key characteristics of the Frymaster H50. Constructed with high-quality materials, this fryer is built to withstand the rigors of heavy usage in commercial settings. The removable fry pots offer easy access for cleaning and maintenance, ensuring that the fryer stays in optimal working condition with minimal downtime.

Another important aspect of the Frymaster H50 is its energy efficiency. The fryer is designed to consume less energy while still delivering superior frying results, which is an essential factor for businesses looking to reduce their operational costs.

Overall, the Frymaster H50 combines innovative technology with user-friendly features to deliver a high-performing commercial frying solution. Its advanced oil management system, precise temperature control, and durable construction make it an excellent choice for any food service operation looking to elevate their frying capabilities.
Top Page Image Contents