Frymaster H50 manual Frequently Used Test Points for Interface Board

Page 9

FREQUENTLY USED TEST POINTS FOR INTERFACE BOARD 106-0386

TEST

METER

PINS

RESULTS

SETTING

 

 

 

12VAC Power to Controller

50VAC Scale

1 and 3 on J3 or J2

12-18

 

 

 

 

24VAC Power to Right Module

50VAC Scale

8 on J3 and GROUND

22-28

 

 

 

 

120 VAC Power

250VAC Scale

11 on J3 and GROUND

110-125

 

 

 

 

120 VAC Power to Blowers

250VAC Scale

12 on J3 and GROUND

110-125

24VAC Power to Full or Right vat High-Limit

50VAC Scale

9 on J3 and GROUND

22-28

24VAC Power to Left High-Limit (if present)

50VAC Scale

9 on J1 and GROUND

22-28

Probe Resistance (Full or Right Vat) *

R x 1000 OHMS

2 and 6 on J3 or 13 and 14 on J2

**

 

 

 

 

Probe Resistance (Left - if present) *

R x 1000 OHMS

2 and 6 on J1 or 14 and 15 on J2

**

 

 

 

 

Probe Isolation

R x 1000 OHMS

6 on J1 or J3 and GROUND

***

 

 

 

 

High-Limit Continuity (Full or Right Vat)

R x 1 OHM

9 on J3 and Wire 13C on Gas Valve

0

High-Limit Continuity (Left - if present)

R x 1 OHM

9 on J1 and Wire 12C on Gas Valve

0

*Disconnect 15-pin harness from controller before testing probe circuit.

**See Probe Resistance Chart at the end of the chapter.

***5 mega-Ohms or greater.

1.1.3 THERMOSTATS

Pro (H50/55) Series gas fryers have temperature probes located on the front centerline of each frypot (dual-vat frypots have two probes, one in each vat). In this type of thermostat, the probe resistance varies directly with the temperature. That is, as the temperature rises, so does resistance, at a rate of approximately 2 ohms for every 1º F. Circuitry in the controller monitors the probe resistance and controls burner firing when the resistance exceeds or falls below programmed temperatures (setpoints). The temperatures are programmed by means of a keypad on the face of the controller.

Pro (H50/55) Series fryers are also equipped with a high-limit thermostat. In the event that the fryer fails to properly control the oil temperature, the high-limit thermostat prevents the fryer from overheating to flash point. The high-limit thermostat acts as a normally closed power switch that opens when exposed to temperatures above 425ºF to 450ºF (218ºC to 232ºC). The different types of thermostats have different part numbers for CE and non-CE models and are not interchangeable.

1.2Accessing Fryers for Servicing

DANGER

Moving a fryer filled with cooking oil may cause spilling or splattering of the hot

liquid. Follow the draining instructions in Chapter 4 of the Installation and Operation

manual (P/N 819-5991) before relocating a fryer for servicing.

1.Shut off the gas supply to the unit. Unplug the power cords. Disconnect the unit from the gas supply.

2.Remove any attached restraining devices and relocate the fryer for service accessibility.

1-4

Page 8 Page 10
Image 9
Page 8 Page 10
Contents 8196083 Hour Service HotlineCanada Page PRO H50/55-SERIES GAS Fryers Table of Contents Parts List Electronic Ignition System Functional DescriptionInterface Board LED Diagnostic LightsInterface Board Frequently Used Test Points for Interface Board Checking the Burner Manifold Gas Pressure Cleaning the Gas Valve Vent TubeNon-CE Standard Burner Manifold Gas Pressures Measuring Flame Current Replacing the Temperature Probe or High-Limit Thermostat Replacing an Ignition Module Replacing the Interface BoardReplacing or Cleaning a Combustion Air Blower Blower Housing Blower Wheel Adjusting the Air/Gas Mixture Page ALL Other Valves Page Replacing the Frypot Page Replacing Frypot Insulation and/or Upper Burner Rails Disassembling a Frypot Full-vat Illustrated Page Page Re-assembling a Frypot Full-vat Illustrated Ignition Failure Troubleshooting and Problem IsolationImproper Burner Function Problems Related to the GAS ValvePage Computer Malfunctions Improper Temperature ControlFiltration Malfunctions Pump Verifying Solenoid Operation LeakageBasket Lift Malfunctions Binds and Jams Interpretation of Analog Controller Lights Troubleshooting Guides Troubleshooting the 24 VAC CircuitPage Volt Circuit Left VAT Right VAT Troubleshooting the Temperature Probe Troubleshooting the Gas ValveProbe Resistance Charts Probe Resistance ChartModule Wiring Diagram for Full-Vat Simplified Wiring DiagramsDiagram WiringFull AustrailiaSingle-Spark VatLeft VAT Right or Full VAT Principal Wiring ConnectionsFull VAT Wiring Diagrams Pro H50/55-Series Fryer, Multi-vatPro H50/55-Series Fryer, Single, Full-vat Pro H50/55-Series Fryer, Single, Dual-vat Pro H50/55-Series Fryer, Single, CE Pro H50/55-Series Fryer, Single, FAST-ready 11.6.2 FPH150/155 Transformer/Filter Box Fpph 250/255/450/455 Transformer/Filter Box Fpph 350/355 Transformer/Filter Box Modular Basket Lift 100/120V Right Side Modular Basket Lift 208/250VPage PRO H50/55-SERIES GAS Fryers Parts List Basket Lift Assemblies Component Cabinetry Backs, Doors, Flue Caps, Sides, and Top Caps Component See Page 2-4 for upper hinges Component 2-inch Hex Washer Manifold, Rear not present in single fryers Full-vatNon-CE Export not available for CE Units ControllersPage Roller, Filter Pan See Note at bottom Drain Valves and Associated Components Component Oil Return Line Components Component Oil Return Handle, Oil Disposal and Disposal Hose Components 810-0783 Cotter Pin 19 810-0285 Swivel, Valve Control Assembly Wand Plumbing Japan Oil Disposal Wand AssemblyNut furnished With Item Rear Flush Oil Return ComponentsElbow, 90º x ½-inch Street Power Shower Assembly, Dual-vat, Complete Power Shower Assemblies OptionalComponent Boxes Electronics and Electrical ComponentsCable, 21-inch Ignition comes with Rajah connector Item Transformer Nut, 8-32 Keps Hex High-Limit Thermostat and Temperature Probe Frypot Components Associated Components Full-VatComponent Dual-Vat Frypot Components For rear flush oil return components, see PH250/255 Full Vat Gas Manifold Typical Gas Supply and Combustion System ComponentsCE Conversion Kits Gas Valves and Associated Components Gas Valve Wiring Wiring Assemblies and Harnesses Main Wiring Harnesses Miscellaneous Connectors and Terminals Ring two required Single H50/55 Filtration System ComponentsBracket, Valve used to attach Item 3 to Item Single H50/55 Oil Return ComponentsSingle H50/55 Component Boxes Single H50/55 High-Limit Thermostat and Temperature Probe Single H50/55 Transformer Boxes Service Hotline
Related manuals
Manual 100 pages 47.98 Kb Manual 70 pages 55.37 Kb

H50 specifications

The Frymaster H50 is a state-of-the-art commercial deep fryer designed for efficiency and reliability in fast-paced kitchen environments. Known for its advanced technology and user-friendly features, the H50 is an ideal solution for restaurants, cafeterias, and food service operations looking to enhance their frying capabilities.

One of the standout features of the Frymaster H50 is its innovative oil management system. This system helps maintain optimal oil quality and reduces the frequency of oil replacement, which not only saves costs but also contributes to improved food flavor. The unit is equipped with a built-in filtration system that can clean the oil while the fryer is in use, significantly extending the life of the frying oil and ensuring consistent frying results.

The Frymaster H50 is also designed with advanced temperature control technology. This ensures precise temperature settings, allowing operators to achieve the perfect fry every time. The fryer features a digital control panel that makes it easy to set and monitor frying temperatures, giving chefs the flexibility to prepare a wide variety of fried foods, from crispy french fries to delicate fish fillets.

In terms of performance, the Frymaster H50 boasts a high production capacity, making it capable of handling large volumes of food. This is especially beneficial during peak service hours when demand is at its highest. The fryer can heat up quickly, providing rapid recovery times that keep up with busy kitchen demands.

Durability and ease of maintenance are also key characteristics of the Frymaster H50. Constructed with high-quality materials, this fryer is built to withstand the rigors of heavy usage in commercial settings. The removable fry pots offer easy access for cleaning and maintenance, ensuring that the fryer stays in optimal working condition with minimal downtime.

Another important aspect of the Frymaster H50 is its energy efficiency. The fryer is designed to consume less energy while still delivering superior frying results, which is an essential factor for businesses looking to reduce their operational costs.

Overall, the Frymaster H50 combines innovative technology with user-friendly features to deliver a high-performing commercial frying solution. Its advanced oil management system, precise temperature control, and durable construction make it an excellent choice for any food service operation looking to elevate their frying capabilities.
Top Page Image Contents