Frymaster 8196345 manual Replacing the Temperature Probe or High-Limit Thermostat

Page 14

1.9.2Replacing the Temperature Probe or High-Limit Thermostat

1.Disconnect the fryer from the electrical supply.

2.Drain cooking oil below the level of the probe or thermostat.

3.Lift up on the bezel to disengage the tabs on its lower edge from the control panel frame.

4.Remove the top two screws in the upper corners of the computer.

5.Swing the computer out from the top and allow it to rest on its hinge tabs.

6.Disconnect the computer wiring harness and ground wire from the back of the computer and remove the computer by lifting it from the hinge slots in the control panel frame.

7.Disconnect the ignition cables from the ignitors by grasping the boots and gently pulling toward you.

8.Disconnect the flame sensor wires from the flame sensors.

9.Disconnect the sound device lead from the interface board.

10.If working on the left frypot, cut the wire tie on the wiring bundle and disconnect the main wiring harness 15-pin connector.

11.Remove the component box mounting screws.

12.Rotate the top of the component box out of the frame and carefully pull it out enough to disconnect the wiring harness plug from the back of the box. This will leave one set of wires, enclosed in spiral wrap, connected to the component box.

13.Remove the box and set it atop the fryer to expose the temperature probe and high-limit thermostat.

14.Unscrew the probe or thermostat from the frypot.

15.Apply Loctite® PST56765 pipe thread sealant or equivalent to the replacement part threads and screw the replacement part into the frypot, torquing to 180 inch-pounds.

16.Connect the wires from the new component as follows:

a.If replacing the temperature probe, use a pin pusher to disconnect (one at a time) the red and white leads from the connector and insert the corresponding leads from the new probe into the plug..

b.If replacing the high-limit thermostat, use a pin pusher to disconnect the lead running to the connector and insert the corresponding lead from the new thermostat. Disconnect the other lead from the drain safety switch and connect the remaining lead from the new thermostat.

17.Reverse steps 1 through 13 to complete the procedure.

1.9.3 Replacing the Interface Board

1.Perform steps 1 through 4 from section 1.9.1.

2.Disconnect the wires attached to the interface board, marking or making a note of the wires and terminals to facilitate reconnection.

3.Remove the nuts at each corner of the interface board and carefully pull it from the studs far enough to allow the connector on the back of the board to be disconnected, then remove the board from the box. When removing the board, be careful not to lose the spacers that fit over the studs behind the board.

4.Recover the relay(s) from the failed interface board and install on the replacement board.

5.Reverse the procedure to install the replacement board, being sure that the spacers behind the board are in place.

6.Reverse the steps to reinstall the computer.

1-8

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Hour Service Hotline GASCanada Iii Protector Series GAS Fryers Table of Contents Protector Series GAS Fryers This page Intentionally Left Blank Functional Description Electronic Ignition SystemLED Diagnostic Lights Interface BoardPage Accessing Fryers for Servicing ThermostatsCleaning the Gas Valve Vent Tube Checking the Burner Manifold Gas PressureNon-CE Standard Burner Manifold Gas Pressures Measuring Flame Current Replacing the Temperature Probe or High-Limit Thermostat Replacing the Interface BoardReplacing an Ignition Module Replacing or Cleaning a Combustion Air Blower Adjusting the Air/Gas Mixture Replacing a Gas Valve ALL Other ValvesReplacing a Burner Assembly Replacing the Frypot Page Full Vat Illustrated Replacing Frypot Insulation and/or Upper Burner RailsPage Re-assembling a Frypot Full-Vat Illustrated Troubleshooting and Problem Isolation Ignition FailureImproper Burner Function Improper Temperature Control Computer Malfunctions Filtration MalfunctionsVerifying Solenoid Operation Leakage Basket Lift MalfunctionsBinds and Jams Troubleshooting Guides Troubleshooting the 24 VAC Circuit VAC is not present on the interface board J3 pin 9 LED 5 GVPage Troubleshooting the Gas Valve Replacing the Transformer or Filter RelayProbe Resistance Chart ATO Automatic Top-Off Service ProceduresProblem Probable Causes Corrective Action ATO Automatic Top-Off Troubleshooting8074646 Function Voltage Wire Color ATO Automatic Top-Off Board Pin Positions and HarnessesReplacing the ATO Board or Transformer Replacing the ATO Pump or SolenoidHot-hi-1 Low tempFailure Failure withIgNITION 14.2 CM7 Useful Codes Enter Setup in Tech Mode EnterReset Recovery Fault Call Service Enter 14.3 CM7 Menu Summary Tree 14.4 CM7 Board Pin Positions and Harnesses To update CM7 and ATO software follow these steps Principal Wiring Connections Wiring Diagrams Main Page FPGL330 Transformer / Filter Box Domestic Modular Basket Lift 100/120V Modular Basket Lift 208/250V Simplified Wiring Diagrams FPGL30 Series Full Vat FPGL30 Series FULL-VAT with ONE DUAL-SPARK Ignition ModuleFPGL30 Series FULL-VAT Australia and Pacific RIM FPGL30 Series Full Vat Australia and Pacific RimFPGL30 Series Simplified Wiring FPGL30 Series Data Network Flowchart Protector Series GAS Fryers Parts List AccessoriesBasket Lift Assembly and Associated Parts Component Doors, Sides, Flue Caps, Top Caps and Casters Drain System Components Drain Valves and Associated Parts Drain Tube Sections and Associated Parts Electronics and Electrical Components 2.5.1 Component Boxes Component Boxes Fuse 5A 125V International OnlyTransformer Boxes FPGL230 Computers and Associated Components Wiring Main Wiring Harnesses 2 CM7 and ATO Wiring Harnesses Refer to wiring diagram on Page Full-Vat Frypot Components Frypot Assemblies and Associated Parts Gas Supply and Combustion System Components FPGL30 Full Vat Gas Manifold TypicalComponent Gas Valves and Associated Components Valve, Non-CE Gas Filtration System Components Component Return Valve Assembly and Associated Parts Component ATO Automatic Top-Off BoardATO Automatic Top-Off Solenoid and Pump Assemblies JIB Cradle, JIB/BIB Cap and Pick Up AssembiesWiring Connectors, Pin Terminals and Tools Fasteners Fasteners This page Intentionally Left Blank Service Hotline

8196345 specifications

The Frymaster 8196345 is a premier commercial fryer designed to meet the demanding needs of foodservice operations. Renowned for its efficiency and technology, this versatile model is a popular choice among restaurants, food trucks, and catering companies.

One of the standout features of the Frymaster 8196345 is its high-capacity oil filtration system. This system ensures that the oil remains clean and free of food particles, significantly extending the life of the oil and enhancing the flavor of fried foods. With automatic filtration capabilities, operators can focus on food preparation rather than oil maintenance, resulting in higher efficiency in busy kitchen environments.

The Frymaster 8196345 also incorporates advanced temperature control technology. With precise digital thermostats, the fryer maintains consistent oil temperatures, reducing the risk of overcooking or burning food. This feature is crucial for achieving optimal frying results, especially for delicate items like fish or pastries. The user-friendly controls allow for quick adjustments, ensuring that chefs can adapt to various cooking requirements seamlessly.

Another key characteristic of the Frymaster 8196345 is its durable construction. Built with high-quality stainless steel, this fryer is designed to withstand the rigors of daily use, providing operators with a long-lasting investment. The smooth surfaces also make cleaning and maintenance significantly easier, helping to meet health and safety standards in commercial kitchens.

The Frymaster 8196345 can accommodate multiple basket sizes, allowing users to fry different foods simultaneously without compromising on quality. This flexibility is particularly beneficial during peak service times, allowing establishments to maximize output and minimize wait times for customers.

Additionally, the Frymaster 8196345 is designed with energy efficiency in mind. It features an eco-friendly operation mode, which reduces energy consumption without sacrificing performance. This not only lowers operational costs but also aligns with sustainability initiatives that many modern establishments strive for.

In summary, the Frymaster 8196345 is an exceptional commercial fryer that combines advanced technology, durability, and efficiency. Its high-capacity oil filtration system, precise temperature control, and robust build make it an ideal choice for busy kitchens aiming for consistent, high-quality frying results. Whether it’s for crispy fries, tempura, or chicken wings, the Frymaster 8196345 stands out as a reliable partner for any food service operation.
Top Page Image Contents