Frymaster 8196345 manual Binds and Jams

Page 31

100-120V Configuration

208-250V Configuration

BINDS AND JAMS

Noisy, jerky or erratic movement of the lifts is usually due to lack of lubrication of the rods and bushings. Apply a light coat of Lubriplate® or similar lightweight white grease to the rod and bushings to correct the problem.

Another possible cause of binding is improper positioning of the motor, which prevents the gear from correctly engaging the teeth in the rod. To correct the problem, loosen the screws that hold the motor in place and move it forward or backward until the rod has just enough slack to be rotated slightly.

MOTORS AND GEARS

The most likely problem to be encountered in this category is erratic motion of the lift due to a worn drive gear. Failure to keep the lift rod and bushings properly lubricated will cause unnecessary wear of the gear. Correct the problem by replacing the worn gear.

If the lift cycles correctly but fails to remain in the up position (i.e., goes up, but then slowly settles back down into the frypot), the problem is a failed motor brake. This cannot be repaired and the motor must be replaced.

If power is reaching the motor but the motor fails to run, it is burned out and must be replaced.

ELECTRONICS

Within this category are problems associated with the relays, microswitches, capacitors, resistors, interface board, wiring, and controls. The most common problem in this category is a lift that continuously travels up and down. This is usually caused by a microswitch that is out of adjustment.

Troubleshooting the electronics of the basket lift is the process of verifying current flow through the individual components up to and including the motor. Using a multimeter set to the 250 VAC range, check the connections on both sides of the component for the presence of the applied line voltage.

1-25

Page 30 Page 32
Image 31
Page 30 Page 32
Contents GAS Hour Service HotlineCanada Iii Protector Series GAS Fryers Table of Contents Protector Series GAS Fryers This page Intentionally Left Blank Electronic Ignition System Functional DescriptionInterface Board LED Diagnostic LightsPage Thermostats Accessing Fryers for ServicingChecking the Burner Manifold Gas Pressure Cleaning the Gas Valve Vent TubeNon-CE Standard Burner Manifold Gas Pressures Measuring Flame Current Replacing the Interface Board Replacing the Temperature Probe or High-Limit ThermostatReplacing an Ignition Module Replacing or Cleaning a Combustion Air Blower Adjusting the Air/Gas Mixture ALL Other Valves Replacing a Gas ValveReplacing a Burner Assembly Replacing the Frypot Page Replacing Frypot Insulation and/or Upper Burner Rails Full Vat IllustratedPage Re-assembling a Frypot Full-Vat Illustrated Ignition Failure Troubleshooting and Problem IsolationImproper Burner Function Improper Temperature Control Filtration Malfunctions Computer MalfunctionsVerifying Solenoid Operation Basket Lift Malfunctions LeakageBinds and Jams VAC is not present on the interface board J3 pin 9 LED 5 GV Troubleshooting Guides Troubleshooting the 24 VAC CircuitPage Replacing the Transformer or Filter Relay Troubleshooting the Gas ValveATO Automatic Top-Off Service Procedures Probe Resistance ChartATO Automatic Top-Off Troubleshooting Problem Probable Causes Corrective ActionATO Automatic Top-Off Board Pin Positions and Harnesses 8074646 Function Voltage Wire ColorReplacing the ATO Pump or Solenoid Replacing the ATO Board or TransformerLow temp Hot-hi-1IgNITION Failure withFailure Reset Recovery Fault Call Service Enter Enter Setup in Tech Mode Enter14.2 CM7 Useful Codes 14.3 CM7 Menu Summary Tree 14.4 CM7 Board Pin Positions and Harnesses To update CM7 and ATO software follow these steps Principal Wiring Connections Wiring Diagrams Main Page FPGL330 Transformer / Filter Box Domestic Modular Basket Lift 100/120V Modular Basket Lift 208/250V FPGL30 Series FULL-VAT with ONE DUAL-SPARK Ignition Module Simplified Wiring Diagrams FPGL30 Series Full VatFPGL30 Series Full Vat Australia and Pacific Rim FPGL30 Series FULL-VAT Australia and Pacific RIMFPGL30 Series Simplified Wiring FPGL30 Series Data Network Flowchart Accessories Protector Series GAS Fryers Parts ListBasket Lift Assembly and Associated Parts Component Doors, Sides, Flue Caps, Top Caps and Casters Drain System Components Drain Valves and Associated Parts Drain Tube Sections and Associated Parts Electronics and Electrical Components 2.5.1 Component Boxes Fuse 5A 125V International Only Component BoxesTransformer Boxes FPGL230 Computers and Associated Components Wiring Main Wiring Harnesses 2 CM7 and ATO Wiring Harnesses Refer to wiring diagram on Page Full-Vat Frypot Components Frypot Assemblies and Associated Parts FPGL30 Full Vat Gas Manifold Typical Gas Supply and Combustion System ComponentsComponent Gas Valves and Associated Components Valve, Non-CE Gas Filtration System Components Component Return Valve Assembly and Associated Parts ATO Automatic Top-Off Board ComponentJIB Cradle, JIB/BIB Cap and Pick Up Assembies ATO Automatic Top-Off Solenoid and Pump AssembliesWiring Connectors, Pin Terminals and Tools Fasteners Fasteners This page Intentionally Left Blank Service Hotline

8196345 specifications

The Frymaster 8196345 is a premier commercial fryer designed to meet the demanding needs of foodservice operations. Renowned for its efficiency and technology, this versatile model is a popular choice among restaurants, food trucks, and catering companies.

One of the standout features of the Frymaster 8196345 is its high-capacity oil filtration system. This system ensures that the oil remains clean and free of food particles, significantly extending the life of the oil and enhancing the flavor of fried foods. With automatic filtration capabilities, operators can focus on food preparation rather than oil maintenance, resulting in higher efficiency in busy kitchen environments.

The Frymaster 8196345 also incorporates advanced temperature control technology. With precise digital thermostats, the fryer maintains consistent oil temperatures, reducing the risk of overcooking or burning food. This feature is crucial for achieving optimal frying results, especially for delicate items like fish or pastries. The user-friendly controls allow for quick adjustments, ensuring that chefs can adapt to various cooking requirements seamlessly.

Another key characteristic of the Frymaster 8196345 is its durable construction. Built with high-quality stainless steel, this fryer is designed to withstand the rigors of daily use, providing operators with a long-lasting investment. The smooth surfaces also make cleaning and maintenance significantly easier, helping to meet health and safety standards in commercial kitchens.

The Frymaster 8196345 can accommodate multiple basket sizes, allowing users to fry different foods simultaneously without compromising on quality. This flexibility is particularly beneficial during peak service times, allowing establishments to maximize output and minimize wait times for customers.

Additionally, the Frymaster 8196345 is designed with energy efficiency in mind. It features an eco-friendly operation mode, which reduces energy consumption without sacrificing performance. This not only lowers operational costs but also aligns with sustainability initiatives that many modern establishments strive for.

In summary, the Frymaster 8196345 is an exceptional commercial fryer that combines advanced technology, durability, and efficiency. Its high-capacity oil filtration system, precise temperature control, and robust build make it an ideal choice for busy kitchens aiming for consistent, high-quality frying results. Whether it’s for crispy fries, tempura, or chicken wings, the Frymaster 8196345 stands out as a reliable partner for any food service operation.
Top Page Image Contents