Jenn-Air JRSD209, JRS229, JRS207, JRSDE229, JRSF12250 Starting or Stopping Your Ice Maker, Sensor

Page 11

Certain sounds may accompany the various cycles ofthe ice maker. Examples are: (1) the motor may have a slighthum, (2)the cubes will rattle asthey fall into an empty storage bin, and (3) the water valve may click or "buzz" occasionally. All of these sounds are normal and should be ignored.

Note: When dispensing ice cubes, it is important that you use only the ice supplied by

thisicemaker. Icefromanyothersourcecouldcauseanicejam. Ifthis happens,remove and discard all ice from the storage bin and any ice lodged in the ice chute.

I Starting or Stopping Your Ice Maker I

ICE*UTOMAKERM,T,C

 

Your automatic ice maker is located near the top of

/

SENSOR

the freezer compartment behind the Ice Access

1

ARM

tl

/

Panel. To gain access to the ice making mecha-

_,.,_,_

_,_LOF F

nism, lift the Ice Access Panel.

 

 

The ice maker has a wire sensor arm that is con- nected to a shut-off switch. This arm stops the mechanism when the ice cube storage bin is full,

and restarts it after several ice cubes have been used. You can use the stop arm to stop all production of ice at any time. All you needto do is raise the arm into the OFF position.

The ice maker should be turned off (arm up) when:

1. ice storage bin is to be removed for extendedperiod of time.

2. Refrigeratorisnot tobe usedfor a considerabletime, such as vacations. Also, turn off the water supplyto the ice maker in this instance,if practical.

3. Water supply is to be shut-offfor several hours.

 

 

FILL

Water fills the empty cube mold (Fig. 1)when the

 

TUBE

freezer compartmenthas cooledto freezing tem-

 

 

I How the Ice Maker Works I

 

 

perature. Cold air is forceddirectlyoverthe mold.

 

 

When frozen, the cubes are rotated up and out of

 

iCE

into the ice storage bin below.

'2

BIN

the mold (Fig. 2). The sweeper arm ejects them

F_. Ij/

jJ-,,_----IcE

The sensor arm (Fig. 3) senses when the bin is full

 

 

and signals the ice maker to stop ejecting more

 

 

However,the moldhas beenrefilled and cubes

frozen sothe new supplyis readywhen needed. As soon as ice is removed from the bin, the

sensor arm signals that more is needed. The

ice makerresumes operationby ejectingready- cubes.

and-waiting frozen cubes,

11

I_

_

__POSlTION

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Model JRSDE249 LmJENN-AIRAbout Your Jegerator Electrical Connection and Grounding Safety PrecautionsLeveling Is Important LocationWarm Cabinet Surfaces Setting ControlsTemp Control Drawer Model JRS207 Shelves jSlide-OutShelves Some models Wine Rack Most models1 Sealed CrispersHumidity Control Most models Shelf Tender Automatic Door Closers and Magnetic Door GasketsLiltOffDOf Shelves Slide-Out Door Shelves Model JRSD279Freezer Compartment Features Automatic Ice Maker Select Modelsl Freezer Baskets JRSD279 tSensor Starting or Stopping Your Ice MakerWaterfrothaOm,sponser,soh,,edce, ,dorwatar llil li Child Proof Lock J To Stop DispensingSi,e Condenser Defrost PanLGoing On Vacation Replacing Light BulbsRefrigeratorwont run Freezer compartment too warm If You Need Service
Top Page Image Contents