Jenn-Air JGS8860, JGS8850 manual Cancel, Clock, Timers

Cancel

The CANCEL button stops any function except the Clock, Timer and Control Lock. When you press the CANCEL button, the display will show the time of day, or the time remaining if the TIMER is being used.

Clock

To Set Clock:

1.Press SETUP.

2.Select CLOCK using the left Quickset pad.

3.Select TIME using the left Quickset pad.

4.Enter the time using the number pads.

5.Press ENTER on the number pads.

6.Select AM or PM in 12-hour mode. (For 24-hour clock, see following.)

7.To exit the Setup mode, press SETUP.

Entering the Day of the Week:

1.Press SETUP.

2.Select CLOCK using the left Quickset pad.

3.Press the right Quickset pad to scroll until DAY is displayed.

4.Select DAY using the left Quickset pad.

5.Use right Quickset pad to scroll through the days.

6.Select the day desired using the left Quickset pad.

7.To exit the Setup mode, press SETUP.

To Set the Clock for a 12 or 24 Hour Format:

The clock can be set to display time in either a 12-hour or 24- hour format.

1.Press SETUP.

2.Select CLOCK using the left Quickset pad.

3.Use right Quickset pad to scroll to 12/24 HOUR.

4.Press the left Quickset pad to select 12/24 HOUR.

5.Select 12 HR or 24 HR using the right or left Quickset pad.

6.To exit Setup mode, press SETUP.

Activating and Canceling the Clock/Day of Week Display:

1.Press SETUP.

2.Select CLOCK using the left Quickset pad.

3.Press the right Quickset pad to scroll until DISABLE is displayed.

4.Select DISABLE using the left Quickset pad.

5.Select TIME using the left Quickset pad.

6.Select ON or OFF using the right or left Quickset pad to turn the clock display On or Off.

Day of the week:

7.Use right Quickset pad to scroll to DAY.

8.Select DAY using the left Quickset pad.

9.Select ON or OFF using the right or left Quickset pad to turn the Day of the Week display On or Off.

10.To exit the Setup mode, press SETUP.

Timers

Setting the Timers (Timer 1 or Timer 2):

1.Press TIMER 1 or TIMER 2.

2.Press one of the displayed times using the Quickset pads, or press the number pads to enter the desired time.

IMPORTANT: Each press of the displayed time choices adds additional time. For example, pressing “10 MIN” three times provides 30 minutes on the timer (0:30).

3.Press ENTER (located on the number pad).

Changing the Amount of Time Entered Once the Timer Starts:

1.Press TIMER 1 or TIMER 2 once.

2.Press the displayed times on the Quickset pads repeatedly until the desired time is entered.

OR

Press the number pads to enter the new desired time.

3.Press Enter pad.

Canceling the Timer:

1.Press TIMER 1 or TIMER 2 twice.

If Both Timers Are Active:

If the desired Timer is already in the foreground, press once for edit mode and twice to cancel the Timer. If the desired Timer is not in the foreground, follow these steps:

1.Press the desired TIMER pad once. The selected Timer will come to the foreground.

2.Press TIMER a second time to access the edit mode in order to make changes.

3.Pressing TIMER a third time will cancel the Timer.

Changing the Timer Beeps:

The signal beeps for TIMER 1 and TIMER 2 can be changed. The options available are 2 beeps every 30 seconds, 2 beeps every 60 seconds or 1 beep only. The default setting is 1 beep.

1.Press SETUP.

2.Use right Quickset pad to scroll to TONES.

3.Select TONES using the left Quickset pad.

4.Use right Quickset pad to scroll to TIMERS TONES.

5.Select TIMERS TONES using the left Quickset pad.

6.Use right Quickset pad to scroll to the desired timer beep format (2-30 SEC, 2-60 SEC or 1 BEEP).

7.Select the desired beep using the left Quickset pad.

8.Press SETUP to exit Setup mode.

9