Jenn-Air W10298937B Installation Requirements, Tools and Parts, Location Requirements

Page 2

INSTALLATION REQUIREMENTS

Tools and Parts

Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.

Tools needed

Tape measure

Marker or pencil

Flat-blade screwdriver

Pliers

Phillips head screwdriver

¼" drill bit

Drill

Jigsaw

Level

Ratchet with ³⁄₈" socket

6" socket extension

Parts supplied

Vent grille

Grease filter

Grill cartridge

Grease container(s)

Hold-down straps (4)

Clamping screws (4)

Parts needed

A UL listed or CSA approved strain relief for ⁷⁄₈" (2.2 cm)

knockout.

A UL listed or CSA approved conduit connector for

¹⁄₂" (1.3 cm) trade-size metal-clad conduit

UL listed wire connectors

Metal ducting

Use the countertop opening dimensions that are given with these Installation Instructions. Given dimensions are minimum clearances and provide 0" (0 cm) clearance.

Grounded electrical supply is required. See “Electrical Requirements” section.

If cabinet has drawers, drawers will need to be removed and drawer fronts installed on front of cabinet.

IMPORTANT: An under-counter built-in oven cannot be installed under this product.

Product Dimensions

30" (76.2 cm) Cooktop

BC

A D

E

F

A. Tie down bolt (on each side of cookop)

B. 30" (76.2 cm)

C. 21³⁄₄" (55.3 cm)

D. Grease containers

E. Wiring box cover

F. Blower

Jenn-Air wall cap

Jenn-Air®6" (15.2 cm) Round Surface Wall Cap Damper

Order Part Number A406

Jenn-Air®3¼" x 10" (8.3 x 25.4 cm) Surface Wall Cap Damper

Order Part Number A403

To order, see the “Assistance or Service” section of the Use

and Care Guide.

Vent clamps

Check local codes. Check existing electrical supply. See

B

A*

C

D**

E

F

G

C H

“Electrical Requirements” section.

It is recommended that all electrical connections be made by a licensed, qualified electrical installer.

Location Requirements

IMPORTANT: Observe all governing codes and ordinances. When installing cooktop, use minimum dimensions given.

To eliminate the risk of burns or fire by reaching over the heated surface units, cabinet storage space located above the surface units should be avoided. If cabinet storage is to be provided, the risk can be reduced by installing a range hood that projects horizontally a minimum of 5" (12.7 cm) beyond the bottom of the cabinets.

A. 6¹⁄₄" (15.9 cm)

E. 13³⁄₄" (34.9 cm)

B. 3¹⁄₂" (8.9 cm)

F. 11¹³⁄₁₆" (30.0 cm)

C. Grease containers

G. 4" (10.2 cm)

D. 2" (5.1 cm)

H. 13¹³⁄₁₆" (35.1 cm)

*A minimum clearance of 6¹⁄₄" (15.9 cm) is recommended for removal of the grease containers. Installed dimension for the grease containers is 5¹⁄₂" (14.0 cm).

**A minimum clearance of 2" (5.1 cm) is recommended between the motor/blower and cabinet for proper cooling.

2

Image 2
Contents Cooktop Safety Table of Contents/Table des matièresLocation Requirements Installation RequirementsTools and Parts Cabinet Dimensions 45 114.3 cm CooktopFor Best Performance Cutout DimensionsVenting Requirements Makeup Air Cold Weather InstallationsVenting Methods Option 1 Roof Venting Option 2 Wall VentingCalculating Vent System Length Concrete Slab Installations Exhaust Through WallConcrete Slab Installations Exhaust Through Window Well Vent Piece Cm RoundExample vent system Determine Range Blower SettingElectrical Requirements To Convert to High RangePrepare Cooktop Before You Make the Electrical ConnectionTo rotate blower Rotate Blower OptionalTo rotate blower motor Make Electrical Connection Install CooktopIf your home has You will be Go to Section Connecting to Electrical Connection OptionsComplete Installation If you need Assistance or ServicePage Sécurité DE LA Table DE Cuisson Exigences DinstallationExigences d’emplacement Outillage et piècesDimensions du produit Table de cuisson de 30 76,2 cm Table de cuisson de 45 114,3 cmDimensions du placard Dimensions de l’ouverture à découperPour obtenir la meilleure performance Installations pour régions à climat froidExigences concernant lévacuation Air d’appointMéthodes dévacuation La caisseExemple de circuit dévacuation Conversion au mode à forte aspirationCalcul de la longueur effective du circuit dévacuation Détermination du réglage du ventilateurSpécifications électriques Avant d’établir la connexion électriqueRotation du ventilateur Facultative Instructions D’INSTALLATIONPréparation de la table de cuisson Pour faire pivoter le ventilateurPour faire pivoter le moteur du ventilateur Installation de la table de cuissonRaccordement électrique Distribution Suivante Options de raccordement électriqueCâblage de la maison Point de Achever linstallation Si vous avez besoin dassistance ou de service2012 All rights reserved