Middleby Marshall PS624E Door Safety Switch, Blower Switch, Heat / Conveyor Switch

Page 20

SECTION 3

OPERATION

II.COMPONENT INFORMATION AND LOCATION (Figures 3-1 and 3-2)

A. Door Safety Switch

The Door Safety Switch is located at the lower right side of control panel opening. Opening the control panel door permits this switch to open, disconnecting power to all electrical controls, except for the blower motor inverters, located in the left side control cabinet.

CAUTION

Do NOT touch the wires going to this safety switch. Current is always present.

B. Blower Switch

The blower switch has two positions. The switch must be “ON” or “I” for the main blowers to come on and permit the oven to run. The fan circulates the air throughout the oven and must stay on during baking and during the cool down cycle above 200°F (93°C) to prevent blower

bearing damage. To protect the blower motor and bearings a thermostatic override is built into the oven. If the temperature inside the oven is over 200°F (93°C) the main blower will continue to run after the blower switch is turned to the “OFF” or “O” position.

C. Heat / Conveyor Switch

The “Heat/Conveyor Switch” allows the heat to come on. Activation is determined by the settings on the Digital Temperature Controller.

D. Temperature Controller

The temperature controller is a solid-state, PID type to maintain the operator-set temperature. The temperature controller continuously monitors the oven temperature and turns on the modulating solid state relay controller. The heat is proportioned as required to maintain a constant oven temperature.

The temperature controller contains a low-limit switch which allows the oven to cool down to 200°F (93°C) before shutting off the blower. A high-limit indication (ALM 1) will appear on the display if the oven reaches 650°F (343°C).

#ONVEYOR 0OWER 4RANSFORMER

#OOLINGL&AN

4EMPERATUREU

#ONTROL

#ONVEYOR 3PEED

#ONTROLT"OARD

#IRCUITC"REAKERS

"LOWER-AIN-

3WITCH

(EAT#ONVEYOR

3WITCH

(I,O"LOWER 3PEEDE2ELAY

#ONVEYOR

(IGH ,IMIT

(IGH ,IMIT

$ISC

'EARMOTOR

4HERMOSTAT

2ESET

4HERMOSTAT

Figure 3-2. Interior View of Control Console

16

Image 20
Contents Owners operating Page Middleby Marshall IiiTable of Contents Section Description PS624 Series Oven Specifications PS624-Series Oven Components Locations II. Component Function Cooling Fan Air Finger Section Installation Section Installation Unloading03  /6%. .34!,,!4 152%$ +43 !.$.%150-%.4 Model PS624 Single Oven Dimensions Model PS624 Double Oven Dimensions Model PS624 Triple Oven Dimensions II. Ventilation Guidelines Electric Supply to be Provided by CustomerIV. Electric Supply 11. Junction Connection BoxSection Operation Control FunctionsDoor Safety Switch Blower SwitchHeat / Conveyor Switch Temperature ControllerSee Figures 3-4 Measuring Conveyor SpeedConveyor Startup Procedures Daily Startup Power FailureShutdown Procedure III. STEP-BY-STEP OperationControl Panel Daily Startup Procedure IV. Normal Operation STEP-BY-STEPSP Lock Quick Reference Troubleshooting SymptomSection Maintenance Maintenance Daily ExteriorCooling Fan Conveyor Belt FigureII. Maintenance Monthly Removing Conveyor From Oven For CleaningOosen 4WOO3CREWS and 2EMOVEE#HAIN3PROCKET #OVER Air Fingers Disassembly For Cleaning Standard FingersReassembly of Air Fingers 11. Standard Lower FingerCenter Spacer Extended Lip Flange Finger Manifold Reinstall End Plugs Conveyor Reassembly Into Oven Checking Conveyor Belt TensionConveyor Belt Link Removal Push and hold conveyor end down to reinstall the chain Attaching Drive ChainIII. Maintenance 3 and 6 Month Important NoticesKEY Spare Parts KIT PS624-SERIES Electric Oven KEY Spare Parts KITSection Maintenance Section Troubleshooting Section Troubleshooting Section Electrical Schematics Wiring Diagram, E380V 17.44 kW, PS624E/PS824E Wiring Diagram, E380V 17.4 kW, PS624E/PS824E CE Wiring Diagram, 400-416V 4 kW, PS624E/PS824E Section Electrical Schematics