Fluke 943-227-15, 943-27 manual Normal Operation, Fail Alarm, Power Failure, Loop Failure

Page 22

Operation

Configuration 3

3.3 Operation

Operation of the 943-227-15 Digital Preamplifier is automatic and is controlled by the Model 942A-200C Digital Ratemeter or Model 960 Digital Process Radiation monitoring system. Once the power to the controlling device is turned on, the preamplifier begins operation. No operator interaction is required.

Refer to the instruction manual for the applicable controller, detector and the Model 942-200-80 Communications Option Board for further information.

Normal Operation

If the measured radiation field is within the range of the detector during power-up, the uCi/cc value will be displayed on the controller. The digital display will update once per second.

Alarms

The radiation alarms are initiated by the applicable controller. Refer to the applicable controller manual.

Fail Alarm

There are two equipment failure conditions that can produce a FAIL output or an error display on the associated controller. The fail condition is true whenever any equipment failure is detected and false when no equipment failures are detected.

The following are the fail alarms provided by the 943-227-15 Preamplifier:

1.POWER Failure

2.Loop Test Failure

To return the channel to normal operation after a FAIL alarm, the condition, which caused the alarm, must be located and corrected.

Power Failure

If the power to the controller is lost, the bar graph, alarm indicators, and the display are blanked (turned off). The HIGH, WARN, and FAIL relay coils will de-energize. If power to the preamplifier only is lost, or if there is a break in the power cable, operation of the microprocessor will stop. The display on the controller will then cease to update. If power to the controller is not lost, a break in the interconnecting wiring or the internal communication power fuses on the 977-210-10M Interface board should be checked. Loss of power to the preamplifier will also result in a loop communication failure.

Loop Failure

If the UDR or 960 controller does not receive a valid message from the preamplifier in ten seconds, a loop failure is detected and an E0009 code will normally be displayed. Note the error code displayed is defined by the controlling device, and not by the preamplifier.

The loop failure can originate from bad seating of the serial communications board in the UDR or 960CD, bad connections in the preamplifier, bad connections at the P2 connector of the UDR, a baud rate mismatch between the setting on the serial board and that in the preamplifier, an invalid address setting on the serial board, or blown communication loop fuses.

The baud rate of the preamplifier may be set to either 300 or 4800 baud. SW3-1 on the 977-interface board must be in the ON position to select a baud rate of 4800 baud, the normal setting.

3-4

Image 22
Contents Victoreen Fluke Biomedical Table of Contents Blank General Description General InformationApplication Specifications Preamplifier Variations Application Detector ReadoutFeature Specification Preamplifier Power Jumper Normal Setting Function Alternate Setting Switch Normal Switch FunctionOFF Selects 300 baud 1/ON Selects 4800 baud normal setting Jumper Normal Setting Function Cal. PositionJ4-1 TB1943-227-15 Description Connects To 977-210-10M Detector ConnectionsReceiving Inspection Auxiliary EquipmentRecommended Spare Parts Part Number Description Used OnStorage Blank Theory of Operation Functional DescriptionFunction Hex Address Theory of Operation Main Circuit Boards Bit Position DescriptionTest Point Function RS232 TransmitVictoreen Communications Loop 943-227-15VL RS232C CommunicationsEnables Victoreen Loop Jumper Normal Function Alternate SettingJumper Normal Function Cal Setting Position Preamplifier Mounting InstallationOperation Electrical InterfaceSet-up Digital Preamplifier Operation Fail AlarmPower Failure Normal OperationTo B Normal Operation To C PGA Offset Adjust Configuration FunctionsTo B Enables Victoreen Loop To C Enables RS232C Normal Firmware VersionSet Point Error Codes Software CalculationsBlank Electronic Adjustments Maintenance, Calibration and TroubleshootingMaintenance Electronic CalibrationTroubleshooting Troubleshooting / AdjustmentsConnector Designations Connector DESIGNATIONS, 943-227-15 and 943-227-15VLSwitch and Jumper POSITIONS, 943-227-15 and 943-227-15VL Applicable Drawings 943-227-15VL Related Manuals Not Supplied with this documentBlank Bill of Materials- 943-227-15 and 943-227-15VL Bill of MaterialsPart Number Description Blank Cable Termination Instructions Cable Termination InstructionsDetector Cable Termination Digital Preamplifier HV Connector Notes HV Digital Preamplifier Cable Termination Instructions D Digital Preamplifier Appendix Cable Termination Instructions Digital Preamplifier Modification Sheets, Engineering Instructions Modification Sheets, Engineering InstructionsBlank Blank Fluke Biomedical

943-227-15, 943-27 specifications

The Fluke 943-27 and Fluke 943-227-15 are advanced electrical testing tools designed to meet the demands of professionals in industrial and commercial settings. Recognized for their accuracy and reliability, these devices come loaded with essential features tailored to ensure optimal performance during electrical measurements.

The Fluke 943-27 is a compact yet powerful multimeter that excels in providing precise voltage and current readings. It is equipped with a large, backlit display that ensures visibility in low-light environments. The device supports a wide range of testing parameters, including AC and DC voltage, resistance, continuity, and capacitance measurements, making it invaluable for troubleshooting electrical circuits.

On the other hand, the Fluke 943-227-15 offers additional capabilities, including advanced data logging features. This multimeter allows users to record and analyze measurements over time, which is particularly useful for identifying intermittent issues in electrical systems. Its connectivity options enable seamless data transfer to a computer or mobile device, facilitating easy documentation and reporting.

Both models illustrate a robust construction built to endure tough working conditions. They meet stringent safety standards, which is critical for protecting users from electrical hazards. The ergonomic design ensures comfort during prolonged use, and features like overmolding enhance grip and durability.

One of the standout technologies in these multimeters is Flukeā€™s True-RMS measurement capability. This feature ensures accurate readings of non-linear loads, which are common in modern electrical systems with variable frequency drives and other electronic devices. Additionally, the built-in low-pass filter technology reduces noise in measurements, ensuring precision even in environments with significant electrical interference.

The Fluke 943-27 and 943-227-15 are also designed to be user-friendly. They feature intuitive controls and a straightforward user interface, allowing technicians to navigate functions effortlessly. The ability to perform automatic ranging simplifies measurements, eliminating the potential for errors when setting the range manually.

In conclusion, the Fluke 943-27 and 943-227-15 represent essential tools for electrical technicians who require versatility, accuracy, and durability in their testing equipment. With advanced features, reliable technologies, and a user-centric design, these multimeters not only meet but exceed the expectations of professionals in the field.