Maytag Electric Microwave installation instructions Roof-Vented Installation, Ports

Page 12

STEP 3: Prepare The Venting Blower

4.Reassemble the blower wire. See Figure 14.

5.Rotate the unit so that the exhaust ports face the rear of the cabinet. See Figure 16. When you insert blower unit, blower wire must be like figure 15.

6.Place blower unit back into cabinet. Check that the exhaust ports face towards the rear of the cabinet. See Figure 16.

7.Reattach the blower plate to cabinet so the exhaust ports and blower plate opening are aligned. Attach with one blower unit mounting screw and then one blower plate mounting screw. See Figure 17.

blower unit

Figure 14

exhaust

Figure 15 ports

Roof-Vented Installation:

1.Remove one blower unit mounting screw and one or two blower plate screw(s). Remove the blower plate from cabinet. See Figure 18.

2.Use side cutter or thin snips to cut and remove knockouts "A" from Blower plate. Discard knockouts. Be careful not to distort the plate. See Figure 19.

3.Carefully lift the blower unit out of the microwave oven.

4.Rotate blower unit 90° so the exhaust ports face the upper of the cabinet. See Figure 20.

5.Reassemble the blower wire.

6.Place blower unit back into microwave oven.

7.Reattach blower plate to microwave oven. Attach with the one blower unit mounting screw and then the one or two blower plate mounting screw(s). See Figure 21.

8.Attach the exhaust adapter to the blower plate by sliding it into the Guide. See Figure 22.

exhaust

 

ports

Figure 16

 

blower plate mounting screw

blower plate

blower unit

back plate

blower unit

blower unit

mounting screw

exhaust ports

 

Figure 17

blower plate mounting screw

blower unit

blower plate back plate

 

blower unit

parts “B”

mounting screw

Figure 18

 

 

Knockouts “A”

blower plate

Figure 19

blower unit

Exhaust

blower plateadaptor mounting screw

Back of oven

blower

 

blower unit

unit

blower plate

mounting screw

Figure 20

Figure 21

Figure 22

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Contents Electric MicrowavePage Important Safety Information Recognize this symbol as a Safety messageGrounding Instructions Oven Must be grounded. Grounding reducesMake Sure You Have Enough Space And Support Damper/duct connector Parts, Tools, MaterialsParts, Tools, Materials Power-Supply-Cord Hole Prepare The Electrical ConnectionR N I N G Upper Cabinet Grounded OutletPrepare The Venting System R N I N G F I R E H a Z a R DWall Venting Roof Venting Room VentingStandard Fittings Duct Length 73 ftRoom-Vented recirculating Installation Wall-Vented InstallationPrepare The Venting Blower Before You StartRoof-Vented Installation PortsPrepare The Wall & Upper Cabinet Measure And Track/Tape Up The TemplatesDrill The Holes In The Wall And Upper Cabinet Install The Mounting Plate Oven Must Be Connected To At Least One Wall StudFor Wall-Vented Attach The Oven To The Wall Attach The Oven To The Wall Microondas eléctrico ContenidoConserve Estas Instrucciones Información Importante DE Seguridad Reconozca este símbolo como un mensaje de SeguridadInstrucciones para la Puesta a Tierra Asegúrese de tener suficiente espacio y ayuda Un gabarit pour le mur arrière Dimensions réduites Puerta de tiro invertido, conector del ductoCuatro pernos acodillados de 1/4 x 3 Tamaño real Dos tornillos para madera autorroscantesPiezas, herramientas, materiales Paso 1 Preparación de la conexiones eléctricas V E R T E N C I aGabinete superior Tomacorriente Conectado a tierra Orificio para el cordón del suministro eléctricoPaso 2 Preparación del sistema de ventilación Ventilación por el techoVentilación por la pared Ventilación hacia una HabitaciónAccesorios estándar Longitud del ducto= 73pies 22m Paso 3 Preparación del ventilador Antes de comenzarRetire la placa de montaje Instalación de ventilación ambiente recirculaciónInstalación de ventilación en techo Figura 15 escapePaso 4 Preparación de los gabinetes de pared y superior Mida las plantillas y márquelas con cinta métricaTaladre los orificios en la pared y en el gabinete superior Gabarit Pour MUR ArrièrePaso 5 Instalación de la placa de montaje El horno debe estar fijado a un travesaño como mínimoPara ventilación en pared Paso 6 Sujeción del horno a la pared Ducto Électrique à micro-ondes Table des matièresConserver CES Instructions Ce symbole signale un message de Sécurité Consignes DE Sécurité ImportantesInstructions de liaison à la terre Ne pas utiliser de rallonge électriqueUtiliser le gabarit inclus avec la notice de mise en service Clapet de refoulement / raccord de conduit Un serre-câble et Une vis de couleur foncéeUne traversée pour serre-câble Grandeur réelle Quatre tire-fonds de 1/4 x 2 po6 x 51 mmIl faut les outils et matériaux suivants Étape 1 Préparer le raccordement à l’électricité E R T I S S E ME N TArmoire Supérieure Prise reliée à la Terre Trou pour le cordon d’alimentationÉtape 2 Préparer l’évacuation Évacuation par le mur Évacuation par le toitÉvacuation dans la pièce Matériel standard Longueur de conduitÉtape 3 Préparer le ventilateur d’évacuation E R T I S S E M E N TÉvacuation par le toit Étape 4 Préparer le mur et l’armoire supérieure ’avant de l’armoirePlantilla DE LA Pared Posterior Étape 5 Poser la plaque de montage Le four doit être fixé à au moins un montant de murOuvrir la découpe de la boîte pour le conduit mural arrière Étape 6 Fixer le four au mur Évacuation par le toit Poser le conduit d’évacuation dans

Electric Microwave specifications

The Maytag Electric Microwave stands as a testament to modern culinary convenience, designed to complement a busy lifestyle while offering advanced cooking capabilities. Known for its robust performance and reliable construction, this microwave has become a staple in many kitchens across the globe.

One of the standout features of the Maytag Electric Microwave is its powerful cooking wattage. With options typically above 1,000 watts, it ensures that food heats evenly and efficiently, reducing the time spent waiting for meals to be cooked. The quick-cook feature is another highlight, allowing users to prepare favorites with just a touch of a button.

Equipped with sensor cooking technology, the Maytag Microwave takes the guesswork out of cooking. This smart technology uses built-in sensors to detect moisture and adjust cooking times accordingly, ensuring that food is not over or undercooked. This feature is especially useful for pop-corn, baked potatoes, and other foods that vary in size and moisture content.

The spacious interior is designed to accommodate a variety of dish sizes, from dinner plates to large casseroles, making it perfect for families or those who love to entertain. Additionally, the turntable can be easily removed for cleaning and maintenance, ensuring that your microwave stays hygienic.

An intuitive control panel enhances the user experience with easy-to-read buttons and clearly defined options. Many models boast a sleek LED display that illuminates the cooking progress while providing a modern aesthetic that fits seamlessly in contemporary kitchens.

Safety is paramount in kitchen appliances, and the Maytag Electric Microwave does not fall short. Child lock features prevent unsupervised access, and the appliance is built with quality materials that withstand the test of time, ensuring peace of mind for users.

Furthermore, some models come with integrated steam cooking features, which allow for healthier meal preparation. This capability enables food to be cooked in a way that preserves nutrients while delivering moisture and flavor. This versatility is a boon for those looking to maintain a balanced diet without sacrificing taste.

In conclusion, the Maytag Electric Microwave encapsulates a blend of power, functionality, and safety. Whether you are reheating leftovers, preparing meals from scratch, or defrosting, this appliance adjusts to meet your cooking needs. With smart technology and user-friendly features, it's no surprise that the Maytag Electric Microwave is a trusted choice for home cooks around the world.
Top Page Image Contents