Emerson Hot1 manual Warranty Information, Year Warranty

Page 10

Electric Shock Hazard: Using an ungrounded or improperly connected appliance can result in serious injury or death from electrical shock.

This appliance must be grounded. This instant hot water dispenser is equipped with a cord that has a grounding conductor and a grounding pin. The plug must be connected to an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances. Do not modify the plug provided with the appliance – if it will not fit the outlet, have a proper outlet installed by a qualified electrician. Check with a qualified electrician or serviceman if you are in doubt as to whether the instant hot water dispenser is properly grounded.

Personal Injury: This tank is a non-pressurized tank. DO NOT modify this system.

DO NOT close vent tube or connect other type dispensers or valves to the tank. Use only the InSinkErator dispenser faucet supplied. Use only parts provided. Contact an authorized InSinkErator Service agent for repairs or replacement components.

Fire Hazard: To minimize possibility of fire, DO NOT store flammable items such as rags, paper or aerosol cans near the tank. DO NOT store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.

Property Damage: To avoid water damage, replace any loose or split tubing. Periodically inspect the unit for any signs of leakage and immediately remove from service any unit suspected of leaking.

An instant hot water dispenser, like any water heater, has a limited life and will eventually fail. To avoid possible property damage, this instant hot water dispenser should be regularly examined for leakage and replaced when necessary. A drain pan, plumbed to an appropriate drain or outfitted with a leak detector, should be used in those applications where any leakage could cause property damage.

WARRANTY INFORMATION

1-Year Warranty

Covers all replacement parts and labor to correct defects in material or workmanship in the dispenser system, for the full warranty period from the date of installation in your home. If warranty service is required during the warranty period, contact an authorized InSinkErator service agent to replace or repair the unit in your home at no cost to you. If your dispenser is replaced rather than repaired, the warranty on the new unit shall be for the duration of the remaining portion of the original dispenser’s warranty. Note: Warranty is determined by unit serial number and/or date of installation. Purchase or installation receipt may be required to verify warranty status. When service is required, and for the location of your nearest factory authorized service center, call toll free 1-800-558-5700.

The foregoing warranty does not apply to damage or inoperation resulting from accident, alteration, misuse, abuse, improper installation, installation not in accordance with these instructions or local electrical and/or plumbing codes. We do not assume any responsibility for consequential damage. Install using genuine InSinkErator® manufactured components only. Use of non InSinkErator components will void your warranty.

Some states do not allow limitations on how long an implied warranty lasts, or the exclusion or limitations of incidental or consequential damages, so the above limitations or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Instant Hot Water Dispenser What YOU should Know Before YOU Begin Water will be cold since tank has not been plugged in yet Dimensions That operates your disposer PreparationRequired minimum from center of hole to wall Set screw in spout holder Installing the DispenserRemove the spout by loosening Approximately 2 full turnsSaddle valve option not supplied Water Connection OptionsCompression valve or T-fitting option not supplied Shutoff valve option not suppliedConnecting Water to Dispenser Nut FerruleWatertight. If there are any leaks Fill the Tank & Connect PowerFirst, open the shutoff valve all Carefully re-tighten all connectionsWarranty Information Year WarrantyWarranty Disconnect power From unitCare and USE Troubleshooting Problem Possible Cause What to doManual del usuario Componentes EN Este Paquete Cómo Usar Este Manual DE Instrucciones Dimensiones Mismo interruptor de pared que opera su surtidor PreparaciónMuchos propietarios reemplazan el Porta-tubo surtidor Instalación DEL SurtidorQuite el tubo surtidor de agua Aproximadamente 2 vueltasOpciones DE Conexión DE Agua Conecte el tubo de cobre deConexión DE Agua AL Surtidor Conexiones son herméticas. Si hay En primer lugar, abra por completoLa válvula de cierre y observe si sus Alguna fuga, vuelva a apretar conInformación DE LA Garantía Garantía de un añoDesconecte la energía de la unidad Cuidado Y USOLos limpiadores con ácidos, abrasivos Solución DE Problemas Problema Causa Posible QUÉ HacerManuel du propriétaire Composants Dans CE Paquet Comment Utiliser CE Manuel D’INSTRUCTIONS Dimensions Préparation Installation DU Distributeur Option à robinet-vanne non fourni Options DE Raccord D’EAUOption à valve de compression ou raccord en T non fournis Option à robinet de sectionnement non fourniRaccorder L’EAU AU Distributeur Étanches. S’il y a des fuites Ouvrez d’abord le robinet deRegardez si vos raccords sont Resserrez avec soin tous lesInformation SUR LA Garantie Garantie d’un anPour ajuster la Entretien ET UtilisationCoupez le courant à l’appareil Dépannage Problème Causes Possibles Quoi Faire

Hot1 specifications

The Emerson Hot1 is a cutting-edge thermal imaging solution that redefines the standards of temperature measurement in industrial applications. Tailored for maintenance teams and facility managers, it offers a comprehensive suite of features and technologies that enhance operational efficiency and safety.

One of the standout features of the Hot1 is its exceptional thermal sensitivity, which allows users to detect minor temperature variations. This sensitivity is critical for identifying potential problems in equipment before they escalate into costly failures. With a temperature measurement range of -20°C to 1200°C, the Hot1 is versatile enough to be used in various environments, from electrical inspections to mechanical systems.

The Emerson Hot1 incorporates advanced imaging technology, providing users with crisp, high-resolution thermal images. The integration of a robust, built-in camera enables users to capture both thermal and visual images simultaneously, allowing for detailed documentation and precise analysis. This dual-image capability is ideal for thorough reporting, ensuring that stakeholders are well-informed about the state of equipment.

One of the key technologies behind the Hot1 is its predictive maintenance capability. By continuously monitoring temperature data, the device enables users to implement a proactive maintenance strategy. This minimizes downtime and maximizes productivity by addressing issues before they become critical failures. Furthermore, the Hot1’s integrated data logging feature allows users to store and analyze historical temperature trends, offering insights into equipment performance over time.

User-friendly design is another hallmark of the Emerson Hot1. Its intuitive interface simplifies operation, making it accessible for both seasoned professionals and newcomers. The ergonomic design ensures comfort during extended use, and the lightweight construction enhances portability.

Additionally, the Hot1 is equipped with connectivity options, including Wi-Fi and Bluetooth, allowing for seamless integration with mobile devices and computers. Users can quickly upload images and data for remote analysis, further facilitating collaboration and decision-making.

In summary, the Emerson Hot1 thermal imaging device stands out for its combination of high sensitivity, advanced imaging technology, and predictive maintenance capabilities. Its user-centric design and connectivity options make it an invaluable tool for industries seeking to enhance their maintenance strategies, improve safety, and reduce operational costs. The Emerson Hot1 is a testament to innovation in thermal imaging, setting a new benchmark for reliability and performance.
Top Page Image Contents