Emerson Hot1 manual Water will be cold since tank has not been plugged in yet

Page 3

HOW TO USE THIS INSTRUCTION MANUAL

These instructions are separated into main sections, indicated by numbers, and subsections, indicated by capital letters. The manual is setup this way to allow you to take a break at any point after completing a section or subsection without affecting the installation process.

What you’ll see in the instruction manual:

B

Valve

Lever

2

3

Property Damage: Do not connect electric power until tank is filled with water. Failure to do so my damage heating element or thermal safety fuse and will void the warranty.

Press valve lever down for about 20 seconds until water freely runs out of the spout. Hold valve open at lease 60 seconds to let the water run to flush out the lines.

■Water will be cold since tank has not been plugged in yet.

1

1Provides a step-by-step narrative describing the installation step, with check boxes that can be marked as you progress through the installation.

2Contains simple illustrations that provide visual instruction to support the narrative.

3CAUTIONS, WARNINGS and DANGERS that will require your attention during the step.

An imminently hazardous situation, which, if not avoided, will result in death or serious injury.

A potentially hazardous situation, which, if not avoided, could result in death or serious injury.

A potentially hazardous situation, which, if not avoided, may result in minor or moderate injury.

Note: The wall outlet for your dispenser must have power supplied to it continuously and must be fused. It should not be controlled by the same wall switch that operates your disposer.

A 115-volt grounded outlet within 30 inches of the dispenser is required to provide power to the tank.

A minimum of

33⁄4" of space is required between the

center of the dispenser head

and splashboard/ wall in order for the appliance to operate properly.

3

Page 2 Page 4
Image 3
Page 2 Page 4
Contents Instant Hot Water Dispenser What YOU should Know Before YOU Begin Water will be cold since tank has not been plugged in yet Dimensions Preparation That operates your disposerRequired minimum from center of hole to wall Approximately 2 full turns Installing the DispenserRemove the spout by loosening Set screw in spout holderShutoff valve option not supplied Water Connection OptionsCompression valve or T-fitting option not supplied Saddle valve option not suppliedNut Ferrule Connecting Water to DispenserCarefully re-tighten all connections Fill the Tank & Connect PowerFirst, open the shutoff valve all Watertight. If there are any leaksYear Warranty Warranty InformationDisconnect power From unit WarrantyCare and USE Problem Possible Cause What to do TroubleshootingManual del usuario Componentes EN Este Paquete Cómo Usar Este Manual DE Instrucciones Dimensiones Preparación Mismo interruptor de pared que opera su surtidorMuchos propietarios reemplazan el Aproximadamente 2 vueltas Instalación DEL SurtidorQuite el tubo surtidor de agua Porta-tubo surtidorConecte el tubo de cobre de Opciones DE Conexión DE AguaConexión DE Agua AL Surtidor Alguna fuga, vuelva a apretar con En primer lugar, abra por completoLa válvula de cierre y observe si sus Conexiones son herméticas. Si hayGarantía de un año Información DE LA GarantíaCuidado Y USO Desconecte la energía de la unidadLos limpiadores con ácidos, abrasivos Problema Causa Posible QUÉ Hacer Solución DE ProblemasManuel du propriétaire Composants Dans CE Paquet Comment Utiliser CE Manuel D’INSTRUCTIONS Dimensions Préparation Installation DU Distributeur Option à robinet de sectionnement non fourni Options DE Raccord D’EAUOption à valve de compression ou raccord en T non fournis Option à robinet-vanne non fourniRaccorder L’EAU AU Distributeur Resserrez avec soin tous les Ouvrez d’abord le robinet deRegardez si vos raccords sont Étanches. S’il y a des fuitesGarantie d’un an Information SUR LA GarantieEntretien ET Utilisation Pour ajuster laCoupez le courant à l’appareil Problème Causes Possibles Quoi Faire Dépannage

Hot1 specifications

The Emerson Hot1 is a cutting-edge thermal imaging solution that redefines the standards of temperature measurement in industrial applications. Tailored for maintenance teams and facility managers, it offers a comprehensive suite of features and technologies that enhance operational efficiency and safety.

One of the standout features of the Hot1 is its exceptional thermal sensitivity, which allows users to detect minor temperature variations. This sensitivity is critical for identifying potential problems in equipment before they escalate into costly failures. With a temperature measurement range of -20°C to 1200°C, the Hot1 is versatile enough to be used in various environments, from electrical inspections to mechanical systems.

The Emerson Hot1 incorporates advanced imaging technology, providing users with crisp, high-resolution thermal images. The integration of a robust, built-in camera enables users to capture both thermal and visual images simultaneously, allowing for detailed documentation and precise analysis. This dual-image capability is ideal for thorough reporting, ensuring that stakeholders are well-informed about the state of equipment.

One of the key technologies behind the Hot1 is its predictive maintenance capability. By continuously monitoring temperature data, the device enables users to implement a proactive maintenance strategy. This minimizes downtime and maximizes productivity by addressing issues before they become critical failures. Furthermore, the Hot1’s integrated data logging feature allows users to store and analyze historical temperature trends, offering insights into equipment performance over time.

User-friendly design is another hallmark of the Emerson Hot1. Its intuitive interface simplifies operation, making it accessible for both seasoned professionals and newcomers. The ergonomic design ensures comfort during extended use, and the lightweight construction enhances portability.

Additionally, the Hot1 is equipped with connectivity options, including Wi-Fi and Bluetooth, allowing for seamless integration with mobile devices and computers. Users can quickly upload images and data for remote analysis, further facilitating collaboration and decision-making.

In summary, the Emerson Hot1 thermal imaging device stands out for its combination of high sensitivity, advanced imaging technology, and predictive maintenance capabilities. Its user-centric design and connectivity options make it an invaluable tool for industries seeking to enhance their maintenance strategies, improve safety, and reduce operational costs. The Emerson Hot1 is a testament to innovation in thermal imaging, setting a new benchmark for reliability and performance.
Top Page Image Contents