Installation, Unpacking, Equipment Setup | Antunes, AJ SE-4200/4400

SE-4200/4400 WATER FILTRATION SYSTEM

INSTALLATION

Unpacking

The carton should contain the filtration system and an information packet.

•SE-4200 or SE-4400

•Information Packet

1.Remove unit and all packing materials from ship- ping carton.

2.Remove all packing materials and protective cov- erings from the unit.

2.Remove the information packet. To prevent delay in obtaining warranty coverage, fill out and mail the warranty card.

NOTE: If any parts are missing or damaged, con- tact Antunes Filtration Technologies IMMEDIATELY at 1-800-253-2991 (toll free in the U.S.) or 630-784- 1000.

Equipment Setup

GENERAL

When placing the unit into service, pay attention to the following guidelines.

•Make sure power to the unit is off.

•Do not immerse the power cord or plug in water.

•Keep power cord away from heated surfaces.

ELECTRICAL

Ensure that the line voltage corresponds to the stated voltage on the units specification label. Make sure that the plug on the power cord from the system and the outlet match. For proper operation of the system, and to ensure the highest quality of water from the sys- tem, make sure that the system is not connected to a switched electrical outlet.

An ABC-type fuse (6 Amp, 250 VAC) is located inside the control box.

PLUMBING

NOTE: This unit is designed to use tap water not to exceed 104º F (40º C).

The SE Series uses the following connections:

• Water Inlet (Feed Water)		3/4” NPT
•	Permeate (Product Water)	3/4” NPT
•	Drain	3/4” NPT

When making a plumbing connection to the system, remember to use a back-up wrench on the support plumbing. Always use a good quality and approved pipe sealant or Teflon tape on pipe threads.

Be careful not to get the pipe sealant inside the pipe when making the connections. Do not over tighten the connections.

It is recommended that plastic fittings be used when connecting to the plastic connections of the system. This will reduce the possibility of cracking the connec- tions due to over tightening. If soldered plumbing is used, do not apply heat to, or near, the filtration system.

The use of union (O-ring seal) connections is highly recommended for ease of installation and future servic- ing.

Suggested Tools and Supplies for Installation

The following tools and supplies are suggested to make the installation easier:

•	Screwdriver	•	Adjustable wrenches
•	Drill with bits	•	Pipe wrenches
•	Strap wrench	•	Level
	(up to 6” diameter)	• Pipe dope or Teflon
•	Tape measure		tape

•Two gallon bucket

•Fresh 5 1/4% liq- uid chlorine bleach (such as Clorox®)

CAUTION

This equipment is to be installed to comply with the basic plumbing code of the Building Officials and Code Administrators, INC. (BOCA) and the Food Service Sanitation Manual of the Food and Drug Administration (FDA).

CAUTION

Water Pressure must not exceed 7 bar (100 psi). To reduce water pressure, install a water pressure regulator and set water pressure to suit applica- tion. Note that the trans membrane pressure must be .5 - 3 bar (7.25 - 43.5 psi).

P/N 1010852 Rev. C 04/06

SE-4200/4400 specifications

The Antunes AJ SE-4200/4400 is a state-of-the-art food service equipment model specifically designed for commercial kitchens seeking efficiency, reliability, and precision in cooking. This versatile cooking solution offers operators the ability to prepare a wide range of menu items with unmatched speed and consistency, making it an ideal choice for fast-casual restaurants, hotels, and catering services.

One of the standout features of the Antunes AJ SE-4200/4400 is its advanced cooking technology. Utilizing a combination of radiant heat and high-velocity, impinged air, this model ensures that food is cooked evenly and thoroughly. The dual cooking technology significantly reduces cooking times while delivering superior product quality. This efficient cooking method not only streamlines kitchen operations but also enhances customer satisfaction by providing perfectly cooked meals in minimal time.

The design of the AJ SE-4200/4400 emphasizes user-friendliness, which is crucial in a bustling kitchen environment. Equipped with a digital touch control panel, operators can easily navigate cooking settings, adjust temperatures, and set timers for various menu items. This intuitive interface allows for quick training of staff, reducing learning curves and enabling seamless transitions between different team members.

In addition to its cooking capabilities, the Antunes AJ SE-4200/4400 is designed for easy maintenance. Its stainless steel construction not only ensures durability but also simplifies cleaning and sanitization, adhering to industry standards. The model is constructed with removable components, making it easier for staff to perform routine maintenance tasks without the need for specialized tools.

Another significant advantage of the Antunes AJ SE-4200/4400 is its versatility in cooking applications. Whether preparing sandwiches, pizzas, or other baked goods, this equipment is equipped to handle various food items with precision, enhancing menu flexibility and allowing for creativity in food presentation.

Energy efficiency is also a key consideration in modern food service equipment, and the AJ SE-4200/4400 does not disappoint. Its design is optimized to consume less energy while maintaining high performance levels, allowing operators to reduce operational costs and limit their environmental impact.

The Antunes AJ SE-4200/4400 represents the next step in commercial cooking technology, offering features that cater to the evolving needs of the food service industry. With its combination of innovative cooking methods, user-friendly controls, easy maintenance, and versatility in applications, this model stands out as a premier choice for operators looking to elevate their kitchen operations and delight their customers.