Hoshizaki KMH-2000SWH/3 II. Installation and Operating Instructions, Checks Before Installation

Page 11

II. Installation and Operating Instructions

WARNING

1.This icemaker must be installed in accordance with applicable national, state, and local regulations.

2.CHOKING HAZARD: Ensure all components, fasteners, and thumbscrews are securely in place after installation. Make sure that none have fallen into the storage bin.

A.Checks Before Installation

•Visually inspect the exterior of the shipping container and immediately report any damage to the carrier. Upon opening the container, any concealed damage should also be immediately reported to the carrier.

•Remove the shipping carton, tape, and packing material. If any are left in the icemaker, it will not work properly.

•Remove the panels to prevent damage when installing the icemaker. See "II.B. How to Remove Panels."

•Remove the package containing the accessories.

•Remove the protective plastic film from the panels. If the icemaker is exposed to the sun or to heat, remove the film after the icemaker cools.

•Check that the refrigerant lines do not rub or touch lines or other surfaces, and that the fan blade (if applicable) turns freely.

•Check that the compressor is snug on all mounting pads.

•See the nameplate on the rear panel, and check that your voltage supplied corresponds with the voltage specified on the nameplate.

•This icemaker can be installed on a storage bin 30" wide or wider with a depth of 40" or greater.

•On remote air-cooled model, a remote condenser unit is needed. Hoshizaki Remote Condenser Unit, Model URC-22F is recommended.

B. How to Remove Panels

See Fig. 1

 

• Front Panel: Remove the 2 screws. Lift

Side Panel (L)

up and towards you.

 

• Top Panel: Remove the 2 screws, and lift off.

• Side Panel (R): Remove the screw. Slide forward slightly and lift off.

• Side Panel (L): Remove the 6 screws, and lift off.

Top Panel

Top Insulation

Rear Panel

• Rear Panel: Remove the 6 screws, and

Insulation

lift off.

• Insulation Panel: Remove the

Panel

Front Panel

thumbscrew. Lift up slightly and pull

 

towards you.

 

Side Panel (R)

Fig. 1

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Stackable Crescent Cuber Models KMH-2000SWH/3 KMH-2000SRH/3 Hoshizaki AMERICA, INC Contents Unit Important Safety InformationSerious injury Indicates important information about the use and careKMH-2000SWH water-cooled Specifications Nameplate RatingKMH-2000SWH3 water-cooled KMH-2000SRH remote air-cooled KMH-2000SRH3 remote air-cooled KMH-2000SWH/3 water-cooled Dimensions/ConnectionsKMH-2000SRH/3 remote air-cooled See Fig II. Installation and Operating InstructionsChecks Before Installation How to Remove PanelsLocation SetupPage Installation of Upper Unit Page Additional Warnings for Remote Air-Cooled Model Electrical ConnectionFor All Models KMH-2000SWH3 KMH-2000SRH3 Location Installation of Remote Condenser UnitChecks Before Installation Line Set SetupField Fabricated Line Set Installation Do not USE Thread Sealant Electrical Connection Refrigerant Charge Line Set Exceeding 66 FeetStacking Remote Condenser Units See , 17, or Water Supply and Drain ConnectionsIcemaker KMH-2000SRH/3Water-Cooled Condenser KMH-2000SWH/3 Connection to an Open Drain SystemConnection to a Closed Loop System KMH-2000SWH/3 Connection to a Closed Loop SystemFinal Checklist Startup Cleaning & Sanitizing Instructions III. Cleaning and MaintenanceCleaning Procedure Sanitizing Procedure Following Cleaning Procedure Preparing the Icemaker for Long Storage MaintenanceDrain the water tank Hoshizaki AMERICA, INC

KMH-2000SWH/3, KMH-2000SRH/3 specifications

The Hoshizaki KMH-2000SRH/3 and KMH-2000SWH/3 are high-performance commercial ice machines designed to meet the demands of busy kitchens and establishments where a consistent supply of crushed or cubed ice is essential. Known for their superior technology and reliability, these models are ideal for restaurants, bars, and hospitality venues.

One of the main features of the KMH-2000 series is its robust ice production capacity. With the ability to produce up to 2,000 pounds of ice per day, these machines ensure that you will never run out of ice during peak service hours. This high output is coupled with a spacious storage capacity, accommodating a large volume of ice to minimize the need for frequent refills.

The KMH-2000SRH/3 model comes equipped with an advanced refrigeration system that utilizes a durable air-cooled condenser. This technology not only enhances efficiency but also contributes to energy savings, making it an environmentally friendly option. The use of high-grade stainless steel in the construction of both machines ensures durability and resistance to corrosion, which further extends their lifespan in demanding environments.

Another significant characteristic of these ice machines is their ease of operation. The intuitive control panel allows staff to monitor ice production and makes adjustments effortlessly. The Hoshizaki KMH-2000 series also features a self-cleaning cycle, which simplifies maintenance and helps prevent the buildup of bacteria and mold, maintaining the highest standards of hygiene.

The KMH-2000SRH/3 model specifically boasts a sensor that ensures optimal ice levels, automatically halting production when the bin is full. This not only prevents overflow but also conserves energy. The KMH-2000SWH/3, on the other hand, is designed for environments where space is at a premium, maintaining the same production prowess without compromising on performance.

In conclusion, the Hoshizaki KMH-2000SRH/3 and KMH-2000SWH/3 ice machines offer an outstanding combination of production capacity, reliability, and efficiency. With their advanced technological features and user-friendly design, they represent an excellent choice for any establishment requiring a consistent and abundant supply of high-quality ice. Investing in these machines means investing in a dependable solution that will enhance your operational efficiency and customer satisfaction.
Top Page Image Contents