Hoshizaki KMH-2000SWH/3, KMH-2000SRH/3 instruction manual Cleaning Procedure

Page 31

1.Cleaning Procedure

1)Dilute 38 fl. oz. (1,124 ml) of Hoshizaki "Scale Away" with 7 gal. (26 l) of warm water.

2)Remove all ice from the evaporator and the storage bin.

Note: To remove cubes on the evaporator, turn off the power supply and turn it back on after 3 minutes. The harvest cycle starts and the cubes will be removed from the evaporator.

3)Turn off the power supply.

4)Remove the front panel, then remove the insulation panel by first removing the thumbscrew, lifting up the panel slightly and pulling it towards you.

5)Remove the drain plug located on the lower front part of the ice chute. Allow the water tank to drain.

6)Replace the drain plug in its correct position. Be careful not to cross thread it.

7)In bad or severe water conditions, clean the float switch assembly as described below. Otherwise, continue to step 8.

a.Disconnect the vent tube and the flush tube from the top of the float switch, then remove the float switch assembly. Remove the rubber boot from the bottom of the assembly.

b.Remove the retainer rod from the bottom of the float switch housing, then remove the float. Be careful not to bend the retainer rod excessively when removing it.

c.Wipe down the float switch assembly's housing, shaft, float, and retainer rod with cleaning solution. Clean the inside of the rubber boot and hose with cleaning solution. Rinse the parts thoroughly with clean water.

d.Reassemble the float switch assembly and replace it and the rubber boot in their correct positions. Reconnect the vent tube and the flush tube.

8)Pour the cleaning solution into the water tank.

9)Fully open the cleaning valve on the left side wall of the machine compartment.

10)Move the control switch on the control box to the "WASH" position.

11)Replace the insulation panel and the front panel in their correct positions.

12)Turn on the power supply to start the washing process.

13)Turn off the power supply after 30 minutes.

14)Remove the front panel and the insulation panel.

15)Remove the drain plug. Allow the water tank to drain. Replace the drain plug and the insulation panel in their correct positions.

16)Move the control switch to the "ICE" position.

17)Close the cleaning valve.

Note: The icemaker will not operate unless the cleaning valve is completely closed.

18)Replace the front panel in its correct position.

19)Turn on the power supply to fill the water tank with water.

20)Turn off the power supply after 3 minutes.

21)Remove the front panel and fully open the cleaning valve.

31

Page 30 Page 32
Image 31
Page 30 Page 32
Contents Stackable Crescent Cuber Models KMH-2000SWH/3 KMH-2000SRH/3 Hoshizaki AMERICA, INC Contents Unit Important Safety InformationSerious injury Indicates important information about the use and careKMH-2000SWH water-cooled Specifications Nameplate RatingKMH-2000SWH3 water-cooled KMH-2000SRH remote air-cooled KMH-2000SRH3 remote air-cooled KMH-2000SWH/3 water-cooled Dimensions/ConnectionsKMH-2000SRH/3 remote air-cooled See Fig II. Installation and Operating InstructionsChecks Before Installation How to Remove PanelsLocation SetupPage Installation of Upper Unit Page For All Models Electrical ConnectionAdditional Warnings for Remote Air-Cooled Model KMH-2000SWH3 KMH-2000SRH3 Checks Before Installation Installation of Remote Condenser UnitLocation Line Set SetupField Fabricated Line Set Installation Do not USE Thread Sealant Electrical Connection Refrigerant Charge Line Set Exceeding 66 FeetStacking Remote Condenser Units See , 17, or Water Supply and Drain ConnectionsIcemaker KMH-2000SRH/3Water-Cooled Condenser KMH-2000SWH/3 Connection to an Open Drain SystemConnection to a Closed Loop System KMH-2000SWH/3 Connection to a Closed Loop SystemFinal Checklist Startup Cleaning & Sanitizing Instructions III. Cleaning and MaintenanceCleaning Procedure Sanitizing Procedure Following Cleaning Procedure Preparing the Icemaker for Long Storage MaintenanceDrain the water tank Hoshizaki AMERICA, INC

KMH-2000SWH/3, KMH-2000SRH/3 specifications

The Hoshizaki KMH-2000SRH/3 and KMH-2000SWH/3 are high-performance commercial ice machines designed to meet the demands of busy kitchens and establishments where a consistent supply of crushed or cubed ice is essential. Known for their superior technology and reliability, these models are ideal for restaurants, bars, and hospitality venues.

One of the main features of the KMH-2000 series is its robust ice production capacity. With the ability to produce up to 2,000 pounds of ice per day, these machines ensure that you will never run out of ice during peak service hours. This high output is coupled with a spacious storage capacity, accommodating a large volume of ice to minimize the need for frequent refills.

The KMH-2000SRH/3 model comes equipped with an advanced refrigeration system that utilizes a durable air-cooled condenser. This technology not only enhances efficiency but also contributes to energy savings, making it an environmentally friendly option. The use of high-grade stainless steel in the construction of both machines ensures durability and resistance to corrosion, which further extends their lifespan in demanding environments.

Another significant characteristic of these ice machines is their ease of operation. The intuitive control panel allows staff to monitor ice production and makes adjustments effortlessly. The Hoshizaki KMH-2000 series also features a self-cleaning cycle, which simplifies maintenance and helps prevent the buildup of bacteria and mold, maintaining the highest standards of hygiene.

The KMH-2000SRH/3 model specifically boasts a sensor that ensures optimal ice levels, automatically halting production when the bin is full. This not only prevents overflow but also conserves energy. The KMH-2000SWH/3, on the other hand, is designed for environments where space is at a premium, maintaining the same production prowess without compromising on performance.

In conclusion, the Hoshizaki KMH-2000SRH/3 and KMH-2000SWH/3 ice machines offer an outstanding combination of production capacity, reliability, and efficiency. With their advanced technological features and user-friendly design, they represent an excellent choice for any establishment requiring a consistent and abundant supply of high-quality ice. Investing in these machines means investing in a dependable solution that will enhance your operational efficiency and customer satisfaction.
Top Page Image Contents