Hoshizaki KM-1400SWH/3-M instruction manual Water Supply and Drain Connections, See or, Icemaker

Page 14

G. Water Supply and Drain Connections

See Fig. 9 or 10

WARNING

1.Water supply and drain connections must be installed in accordance with applicable international, national, state, and local regulations.

2.Normal operating water temperature should be within 45°F to 90°F (7°C to 32°C). Operation of the icemaker, for extended periods, outside of this normal temperature range may affect icemaker performance.

3.To prevent damage to equipment, do not operate the icemaker when the water supply is off, or if the pressure is below 10 PSIG. Do not run the icemaker until the proper water pressure is reached.

•A plumbing permit and services of a licensed plumber may be required in some areas.

•External filters, strainers, or softeners may be required depending on water quality. Contact your local Hoshizaki distributor for recommendations.

•Water supply pressure should be a minimum of 10 PSIG and a maximum of 113 PSIG. If the pressure exceeds 113 PSIG, the use of a pressure reducing valve is required.

•The icemaker and condensation drain line(s), storage bin drain line, and water‑cooled condenser drain line must be run separately.

•Drain lines must have 1/4" fall per foot (2 cm per 1 m) on horizontal runs to get a good flow. A vented tee connection is also required for proper flow.

•Drain lines should not be piped directly to the sewer system. An air gap of a minimum of 2 vertical inches (5 cm) should be between the end of the drain pipes from the icemaker and condensation drain, storage bin, and water-cooled condenser and the floor drain.

1. Icemaker

•Icemaker water supply inlet is 1/2" female pipe thread (FPT). A minimum of 1/2" nominal copper water tubing is recommended for the icemaker water supply line.

•An icemaker water supply line shut-off valve and drain valve should be installed.

•Icemaker drain outlet is 3/4" FPT. A minimum of 3/4" nominal hard pipe is recommended for the icemaker drain line. Condensation drain outlet is 3/8" OD hard tube. The condensation drain line can be connected to the icemaker drain line or can be run separately.

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Modular Crescent Cuber Models KM-1400SWH/3-M Hoshizaki AMERICA, INC Contents Indicates important information about the use and care Important Safety InformationSerious injury UnitSpecifications Nameplate Rating KM-1400SWH-M water-cooled marineKM-1400SWH3-M water-cooled marine Dimensions/Connections KM-1400SWH/3-M water-cooled marineHow to Remove Panels II. Installation and Operating InstructionsChecks Before Installation See FigSetup LocationThermostat Extension Bracket stainless Installation of Second Unit Page KM-1400SWH3-M Electrical ConnectionKM-1400SWH-M Icemaker Water Supply and Drain ConnectionsSee or Water-Cooled Condenser Connection to an Open Drain SystemConnection to a Closed Loop System Final Checklist Startup III. Cleaning and Maintenance Cleaning & Sanitizing InstructionsCleaning Procedure Sanitizing Procedure Following Cleaning Procedure Stainless Steel Exterior MaintenancePreparing the Icemaker for Long Storage Storage Bin and ScoopDrain the water tank Remove the water from the water-cooled condenserHoshizaki AMERICA, INC

KM-1400SWH/3-M specifications

The Hoshizaki KM-1400SWH/3-M is a state-of-the-art ice maker designed for high-capacity ice production, catering to the needs of busy commercial establishments such as restaurants, bars, and hotels. Known for its robust construction and innovative technologies, this model stands out in the realm of ice-making equipment.

One of the main features of the KM-1400SWH/3-M is its impressive ice production capacity. It can generate up to 1,400 pounds of crescent ice daily, ensuring that businesses can efficiently meet their ice needs, even during peak hours. The crescent ice produced is not only aesthetically pleasing but also melts slowly, making it ideal for drinks and food preservation.

The KM-1400SWH/3-M utilizes Hoshizaki’s advanced refrigeration technology, which includes a stainless steel evaporator that enhances durability and ensures optimal performance. This model is designed for energy efficiency, often exceeding ENERGY STAR requirements. It features a highly efficient compressor and insulation that minimize energy consumption while maximizing ice production.

Another remarkable characteristic of this ice maker is its user-friendly interface, which simplifies operation and maintenance. The machine includes a built-in control panel that allows easy monitoring of functions and diagnostics. Additionally, the ice maker’s vertical evaporator design reduces the size of the unit while increasing ice production efficiency, making it suitable for tight spaces.

Hoshizaki prioritizes hygiene and ease of maintenance. The KM-1400SWH/3-M has a removable air filter and an automated cleaning cycle that helps maintain optimal sanitary conditions, significantly reducing the frequency of manual cleaning. The antimicrobial surface also aids in preventing bacterial growth, promoting a healthier environment.

In terms of adaptability, the Hoshizaki KM-1400SWH/3-M can work seamlessly with various water conditions, making it a versatile choice for different setups. It operates well in both high and low ambient temperatures, providing consistent ice production regardless of external factors.

Overall, the Hoshizaki KM-1400SWH/3-M is a reliable, high-capacity ice maker that combines modern technology, energy efficiency, and user-friendly features. Its durable construction and innovative design make it an excellent choice for any commercial operation requiring a steady supply of high-quality ice.
Top Page Image Contents